O.K. Jonard Tools EPB Series User manual

134 Marbledale Road • Tuckahoe • NY 10707Tel: [phone] • Fax: [phone] • [e-mail] Series Battery Powered Punchdown ToolUser Manual

2
FEATURES:
Over 1,000 impacts between charges•
Dual action trigger for LED task lighting and impact•
Quick-easy blade lock and release•
90° Blade orientation adjustment for any angled impact•
Hi/Low impact settings easily adjusted•
Powerful, lightweight 7.2V lithium ion battery•
Quick charge battery charger•
Patented•
PRODUCT SELECTION
115 Volt Kits
EPB-1200 Punchdown Tool, Battery, 115V Charger•
EPB-1066 Punchdown Tool, Battery, 115V Charger, 66 blade•
EPB-1110 Punchdown Tool, Battery, 115V Charger, 110 blade•
EPB-11066 Punchdown Tool, Battery, 115V Charger, 110 & 66 blades•
EPB-1000KR Punchdown Tool, Battery, 115V Charger, Krone blade•
230 Volt Kits
EPB-2200 Punchdown Tool, Battery, 230V Charger•
EPB-2066 Punchdown Tool, Battery, 230V Charger, 66 blade•
EPB-2110 Punchdown Tool, Battery, 230V Charger, 110 blade•
EPB-211066 Punchdown Tool, Battery, 230V Charger, 110 & 66 blades•
EPB-2000KR Punchdown Tool, Battery, 230V Charger, Krone blade•
Table of Contents
Features…………………………………………………………….2
Product Selection……………………………………………..2
Operating Instructions.…………….……………………....3
Blade Installation & Orientation.……………………….4
Battery Charger…………………….…………………..………5
Replacement Blades & Accessories…………………..6
Technical Specifications.…………………………………...7

3
Insert the battery into the base of the tool. To remove the1.
battery from the tool, press the battery tabs and pull.
Insert the correct blade into the front of the tool and lock in2.
place (see blade installation on page 4 for more details).
Select the appropriate impact setting based on seating3.
requirements. With two fingers you can easily switch to a high
or low impact setting by turning the red adjustment knob.
Position the wire to be seated on the block4.
The trigger has a dual function design. Squeeze lightly and5.
hold to illuminate the target area with the built in LED light.
Next place the blade over the wire to be seated and push
forward to partially seat the wire. Squeeze the trigger fully to
complete the punchdown. The wire is now seated. If you are
using a blade with a cutter – the excess wire has been trimmed.
If the wire has not been cut, repeat the process.
OPERATING INSTRUCTIONS

4
BLADE INSTALLATION
Point the front end of the tool towards yourself.1.
Insert either end of the blade (cutter or no cutter) into the2.
front end of the punchdown tool - then point away from your
body.
Rotate the blade clockwise until the locking slot of the blade3.
finds the locking pin. The blade will move further into the
blade holder.
Continue turning the blade clockwise until it locks in place4.
NOTE: Failure to lock the blade in place may cause the blade
to discharge causing injury or damage to property.
BLADE ORIENTATION/ROTATION
The blade can be adjusted to one of four positions rotating in 90° increments.
With the front of the tool pointing towards your body, grasp1.
the blade and pull it away from the tool (The blade holder will
extend approximately 1⁄4”).
Twist the blade clockwise 90° and release. The blade holder2.
will retract and the blade will remain locked in its new
position. Repeat this step as needed for alternate positioning.
NOTE: Rotating the blade counterclockwise will unlock the3.
blade.

5
Plug the battery charger into the appropriate electrical1.
outlet. The battery charger LED will blink several times
switching between Red and Green then stays on Green.
Insert the battery into the charger. The LED will turn red,2.
indicating battery is charging
Once the battery is fully charged the LED will turn green.3.
BATTERY CHARGER

6
EPB-1000 ACCESSORIES
EPB-66 66 Blade with & without cutter
EPB-110 110 Blade with & without cutter
EPB-KR Krone Blade with & without cutter
REPLACEMENT BLADES
EPB-B Replacement Lithium Ion Battery
EPB-BC1 115V Battery Charge
EPB-BC2 230V Battery Charger

7
TECHNICAL SPECIFICATIONS
Battery Charger: INPUT: 100 ~ 240VAC, 50-60HZ
OUTPUT: 8.4VDC, 1.3A
Battery: 7.2V, 1.3Ah (Lithium ion battery)
Impact Strength: High position: 30 Lbs. (13.5 kgs)
Low position: 22 Lbs. (10.0 kgs)
Unit weight of tool: 1.32 Lbs. (600 g)
(Not including battery)
Unit weight of battery: .22 Lbs. (100 g)
Tool dimensions: 8.25” x 6.50” x 1.75” (21 x 16.5 x 4.5 CM)
134 Marbledale Road • Tuckahoe • NY 10707Tel: [phone] • Fax: [phone] • [e-mail]

EPB-500 Manual Punchdown Tool
A Transformational redesign of a popular tool
A revolutionary family of impact tools - developed to satisfy ergonomic
necessity and boost operatory efficiency. With worker safety in mind, we
consulted a certified ergonomist and added the following features:
Ergonomic design to minimize repetitive stress and impact recoil•
The easiest high/low impact setting adjustment•
Convenient 2 blade storage compartment•
Non-slip handle•
Reliable fail safe mechanism•
Lifetime Warranty•