Oasis SB-6030R/L User manual

1
These guidelines are recommended for
the proper installation of Oasis products. A
careful review of these procedures (and any
referenced publications) before starting is
important in avoiding an improper assembly
and/or installation.
NOTE: All illustrations in this publication are
typical, and may appear different than the
actual product. Optional items may also be
shown that were not ordered on the product
being installed.
Special Notes to Installer
uIt is the sole responsibility of the installer
to determine the requirements necessary for
compliance with all installation code require-
ments!
uAll paperwork packaged with the product
should be saved and presented to the home
owner upon completion of the installation!
uAll published product dimensions are
for reference only. Any critical dimensions
required for installation should be taken
directly from the product being installed!
u Anyindependentmodicationsmadeto
the product (or any options / accessories
supplied) beyond those required for normal
installation can void all warranties! (Refer to
warranties for further information)
INSPECTION GUIDELINES
Carefully check the unit upon receipt. Notify
your supplier immediately if any questions
or problems are encountered during this
process.
DO NOT INSTALL PRODUCT
WITHOUT FIRST ADDRESSING
QUESTIONS WHICH ARISE DURING
THE INSPECTION!
Basic Module Check
lCheck unit drain position for match to
bathroom drain location.
lCheck unit for surface damage.
lCheck unit color for coordination to other
bathroomxtures.
l Checkunitforspeciedoptionalitems
and/or packages.
INSTALLATION SITE FRAMING
The recommended framing and dimensional
requirements shown are for a traditional
application and may vary, based on site
requirements.
The dimensions shown in the dimensional
diagram(s) are from the surfaces where
the unit will be attached. This surface can
be bare studding, dry wall or other suitable
under layment material. It is important that
theoorandallframingbesquareand
level. Framing must be done using accepted
materials and construction techniques in
accordance with all applicable codes for the
site.
NOTE: Any pre-constructed wall(s) may
requiremodicationoradditionalframingto
allowforfactoryappliedpipesand/orttings
which may protrude from the body of the
unit.
End Drain Shower Base Installations
SB-6030R/L SB-6032R/L SP-60R/L
SP-SB-7v2R/L SP-MB-6R/L ®
SP-60R
SP-60L
SP-SB-7v2R
SP-SB-7v2L (shown)
SB-6030R (shown) SB-6032R
SB-6030L SB-6032L
SP-MB-6R
SP-MB-6L (shown)

2
Illustration 1a - End Drain, Unit Dimension & Alcove Framing Guidelines (dimensional tolerance +0 / -3/8”)
Illustration 1b - End Drain, Unit Dimension & Alcove Framing Guidelines (dimensional tolerance +0 / -3/8”)
SP-60R
(illustrated)
6”
1-1/4”
7-1/4”
36”
17-5/8”
3-3/8“ Dia. Drain
60”
48-3/4”
7/8” Drain Clearance
4”
37-1/4”
1-1/4”
11-1/4”
18-3/8”
SP-SB-7v2L
(illustrated)
6”
Seat Ht.
17-3/4”
31-3/4”
16”
15-3/4”
3-3/8“ Dia. Drain
60”
50-7/8”
5/8” Drain Clearance
4”
9-1/8”
1-1/4”
1-1/4”
14-1/4”
18-3/4”
19-1/2”
SP-MB-6L
(illustrated)
1-5/8”
14-1/2”
32”
33-1/4”
1-1/4”
17-1/2”
60”
1-5/8”
54-1/4”
5-3/4”
3-3/8“
Dia. Drain
Shelves
Molded
Seat
20”
Seat
6”
24-1/4”
25-1/2”
1-1/4”
3-1/4”
1-7/8” Drain Clearance
56-3/4”
Drain Cut-Out
5
“
04
02
Mi
n
i
m
u
m
Al
cove
D
ept
h
,
U
n
i
t
R
oug
h
-
In
D
ept
h
Drain
Center
05
Drain
Center
0
6
07
08
03
Fi
n
ished
Unit Dept
h
0
1
Alcove Length - Unit Width
NOTE: Left End Drain Installation Illustrated.
Fixture
Blocks
Drain Cut-Out
SB-6030R
(illustrated)
1-1/4”
30”
14-1/4”
15-3/4”
3-3/8“ Dia. Drain
60”
51”
2-3/4”
9”
Drip Ledge
1-3/4”
Style Line
3-3/4”
B Drain Clearance
C
A
Drainage
Channel
Std Unit ABF Unit
A 4” 6”
B 1” 3”
C 5-1/4” 7-1/4”
SB-6032R
(illustrated)
Std Unit ABF Unit
A 4” 6”
B 1” 3”
C 5-1/4” 7-1/4”
1-1/4”
32”
16-1/4”
15-3/4”
60”
51” 9”
Drip Ledge
3-3/8“ Dia. Drain
Style Line
Drainage
Channel
B Drain Clearance
C
A
2-3/4”
3-3/4”
Model 01 02 03 04 05 06 07 08
SB-6030R/L 60” 30” 30” 14-1/4” 9” 11-1/2” 11-3/4” 13-1/4”
SB-6032R/L 60” 32” 32” 16-1/4” 9” 11-1/2” 13-3/4” 13-1/4”
SP-60R/L 60” 37-1/4” 36” 18-3/8” 11-1/4” 13-3/4” 15-7/8” 15-1/8”
SP-SB-7v2R/L 60” 31-3/4” 31-3/4” 16” 9-1/8” 11-5/8” 13-1/2” 13-1/4”
SP-MB-6R/L 60” 33-1/4” 32” 14-1/2” 5-3/4” 8-1/4” 12” 15”

3
INSTALLATION PROCEDURE
NOTE: ‘Wet-set’ is not required to support
theoorunderanOasisproductduetothe
encapsulated Balsa wood construction.
With the unit positioned in the framed area,
several details must be checked prior to
securing the unit. (Illust. 2 & 3)
l Conrmtheapron/damisrestingush
ontheoor.
l Conrmdrainposition.
l Conrmtheunitislevelalongeachside
and across each end.
l Conrmtheunitissquareintheframed
installation area.
l Conrmbothinsidefrontcornersare
plumb at each end. (This is critical for
proper door installation)
NOTE: The use of a shims behind the nail-
ingangemayberequiredtoensurethe
unit remains square.
Aftertheunitisconrmedlevelandsquare
within the framing, drill a 1/8” hole through
thenailingangeateachframingmember.
Secure the unit in place across the back
nailingangerst,followedbythesides
andthenalongthefrontverticalanges
(if applicable), using 1-1/4” long nails or
other appropriate fasteners (illust. 4 & 5).
Continually check to make sure the unit
remains plumb within the alcove as it is be-
ing secured.
NOTE: Usage of a thin shield to protect the
unit surface while fastening the unit to the
framing is recommended.
WARNING!
THE INSIDE UNIT SURFACE SHOULD
BE CLEAR OF ALL LOOSE DEBRIS
AND THE SURFACE PROTECTED
BEFORE STEPPING INSIDE.
Water Supply and Drain Connections
Refer to, and follow, the assembly and
installation instructions provided with the
supply valves and drain system. Carefully
check all connections for leaks.
Finishing Guidelines
Fillerstripsorllermaterialmayberequired
over the framing to ensure the under lay-
mentmountsushovertheanges.Awater
resistant under layment is recommended
surrounding the unit. Stop the under lay-
ment 1/16 to 1/8-inch from the unit surface,
andllthespacewithacontinuousbeadof
water resistant sealant. (Illust. 6)
NOTE: Oasis recommends a high qual-
ity silicone based sealant with a mold and
mildew resistant content.
Use care when fastening the under layment
near the unit surface to avoid damage. Seal
the under layment seams and edges, as
required,andinstallthenishmaterialto
specications.
UNIT SURFACE CARE
WARNING!
NEVER USE ABRASIVE MATERIALS,
OR ABRASIVE CLEANERS
ON THE UNIT SURFACE!
EXTREME CAUTION is urged regarding
the use of any cleaner, acid or solvent
on the unit surface.
READ AND FOLLOW PACKAGE
INSTRUCTIONS FOR ALL
PURCHASED CLEANING PRODUCTS!
Through routine use, the unit surface can
collect residues from soap, bath additives
and natural body oils. Additional deposits
can also collect from minerals or particles
found in the water. After each use, wipe the
excesswaterfromtheunit.Thispractice
will reduce the buildup of deposits and help
maintain the natural unit lustre.
Following a thorough surface cleaning,
anapplicationofqualityautomotivewax
will help reduce major accumulations. The
actualscheduleforcleaningandwaxingwill
depend on unit usage and water quality.
WARNING!
NEVER APPLY WAX
TO THE UNIT FLOOR!
uRoutine Cleaning: Mild, non-abrasive
cleanerspecicallyformulatedforgelcoat
and acrylic surfaces recommended. (Rinse
surface thoroughly)
uHeavy Soap Deposits: Liquid ammonia
household cleaner, applied full strength.
(Rinse surface thoroughly)
uStubborn Stains: Liquid household
cleanerorhydrogenperoxideapplied
full strength. Place a saturated clean rag
directly on stain and let stand several hours.
(Rinse surface thoroughly)
uHard Water Scales: Liquid scale remover
or white vinegar, applied full strength.
(Rinse surface thoroughly)
Nailing
Flange
Wall
Framing
2. Level Unit
In Framed Area Confirm unit is level
across the front and
at each end. Wall Framing
1. Position Unit
In Framed Area Wall Framing
Confirm unit apron is
resting flush on floor.
Nailing
Flange
Wall
Framing Confirm Drain Alignment
Illustration 2 -
Unit Installation
Illustration 3 -
Unit Installation

4
uMold/Mildew: Liquid mildew remover or
baking soda and water paste. (Apply paste
andallowtozzseveralminutes.)(Rinse
surface thoroughly)
uConstruction Adhesive: Soften adhesive
with a hand held hair dryer and peel off
adhesive. (Caution is advised when using
any electrical device near water.)
For adhesive residue, apply rubbing alcohol
or nail polish remover, full strength. (Rinse
surface thoroughly)
WARNING!
BATH MATS AND OTHER ITEMS HELD IN
PLACE USING SUCTIONS
MUST BE REMOVED FROM THE UNIT
SURFACE AFTER EACH USE.
OVER AN EXTENDED PERIOD, FAILURE
TO REMOVE
SUCTION ATTACHED ITEMS WILL DAM-
AGE THE UNIT SURFACE.
Nailing Flange
Wall Framing
Drill 1/8 inch hole through
flange at each framing member
Illustration 4 - Securing Unit
Wall
Framing
Secure unit to
framing with
large headed
fasteners.
CAUTION: Protect unit surface
with a shield when fastening.
Nailing Flange
Illustration 5 - Securing Unit
Water Resistant
Underlayment
Waterproof
Sealant
Furring Strip or
Shim Material
Nailing
Flange
Wall Framing
Illustration 6 - Wall Finishing

5
INST-0550.03 / 043013
Oasis Lifestyle, LLC - 1400 Pidco Drive - Plymouth, Indiana 46563
Oasis Lifestyle Product Assurance Program
Bathing and Shower Unit Structure & Surface Finish Limited Warranty
OasisLifestyleprovidesaperformanceassuranceprogramforunitstructuralintegrityandsurfacenishcoveringave
(5) year period from the date-of-purchase on GELCOAT, and covering a ten (10) year period from the date-of-purchase on
VACUUM FORMED ACRYLIC product, for the original purchaser and subsequent consumer. This Oasis limited warranty pro-
gramaddressesspecicdefectsintheproduct,andtheworkmanshipassociatedwiththemanufactureoftheOasisbathing
andshowerproduct.Thespecicdefectscoveredmustresultinasignicantlyalteredappearanceand/oraffecttheintended
performance standards for the product under normal residential use.
Hydro-Massage Systems (water recirculation & air), Option & Accessories Limited Warranty
Oasis Lifestyle provides a performance assurance program for their hydro-massage systems (herein called ‘system’), and
their options and accessories covering a two (2) year period from the date-of-purchase for the original purchaser and subse-
quentconsumer.ThisOasislimitedwarrantyprogramaddressesspecicdefectsinthesystemcomponents,andthework-
manship associated with the assembly of the systems, along with offered options and accessories installed by Oasis, on an
Oasisunit.Thespecicdefectscoveredmustresultinasignicantlyalteredappearanceand/oraffecttheintendedperfor-
mance standards for the system, the option and/or the accessory.
Duringthecoverageperiod,Oasiswill,atitsdiscretion(followingavericationbyanauthorizedOasisrepresentative),either
provideserviceorsupplyareplacementproductwithoutcharge,butexcludinganycostassociatedwiththetransportation,
removalofand/orreinstallationoftheunit(module).FailuretoallowrequestedinspectionbyanauthorizedOasisrepresenta-
tive,and/orfailuretoprovideadequateaccessibilityforanauthorizedinspection,and/orserviceperformedpriortodocument-
edauthorizationfromOasisLifestyle,LLC.,maydelayservice,and/orpossiblyterminateanywarrantycoverage,andremove
any liability to Oasis Lifestyle, LLC.
This ‘Product Assurance Program’ does not cover service resulting the following:
a) Impropereldinstallationoftheproduct,system,option,accessory,and/orsurroundingstructure
modications,and/orutilityserviceconnectionsbeyondtherecommendationssuppliedbyOasisandwithinthe
scope of applicable codes and ordinances; or
b) Carelessness,damage,abuse,misuse,negligence,impropercare,re,ood,oractsofGod;or
c) Non-conforming use, including any use beyond those intended for the product, system, option and/or
accessory, including failure to follow the Prescribed Care and Maintenance Instructions; or
d) Anyunauthorizedalterationsormodicationstotheproduct,system,option,accessoryand/ortheindividual
parts or components supplied by Oasis.
e) Any surface and/or component staining, discoloration, component failure and/or build-up caused as a result of
water chemistry or water quality at the site.
f) Service resulting from normal use and wear for the product, system, option and/or accessory.
Repairorthesupplyingofreplacementproductand/orcomponents,underthislimitedwarrantyprogram,shallbetheex-
clusive remedy. Oasis Lifestyle, LLC., shall not be liable for any incidental or consequential damages, including damages to
thebuilding/structure,thecontents,theoccupants,orbreachofanyexpressedorimpliedwarranties.OasisLifestyle,LLC.,
doesnotrecognize,norauthorizesanypartytoprovideimpliedorwrittenwarrantiesregardingaproduct,system,optionand/
oraccessoriestnessforaparticularpurpose,normodifythetermsofthelimitedwarrantybeyondthosestated.
Somestatesdonotallowtheexclusionorlimitationofincidentalorconsequentialdamages,orallowlimitationsonthedura-
tionofanyimpliedwarranty.Therefore,theaboveexclusionsand/orlimitationsmaynotapply.
THIS WARRANTY PROVIDES SPECIFIC LEGAL RIGHTS, WHICH CAN VARY FROM STATE-TO-STATE.
800.638.8556
HomeInnovation.com
The manufacturer represents that the product to which this
label is affixed (a) duplicates samples independently
tested by Home Innovations Research Labs and certified
to conform to the requirements of HUD UM Bulletin 73a
and the appropriate ANSI Z124 and ICC/ANSI A117.1
standards, and (b) has been manufactured under quality
controls deemed appropriate by the manufacturer and
periodically reviewed by the certifier.
Oasis Lifestyle, LLC
Plymouth, IN
6006
800.638.8556
HomeInnovation.com
The manufacturer represents that the product to which this
label is affixed (a) duplicates samples independently
tested by Home Innovations Research Labs and certified
to conform to the requirements of HUD UM Bulletin 73a
and the appropriate ANSI Z124 and ASME A112.19.7
standards, and (b) has been manufactured under quality
controls deemed appropriate by the manufacturer and
periodically reviewed by the certifier.
Oasis Lifestyle, LLC
Plymouth, IN
6006
®