Oasis Aqua Leader Sentinelle User manual

1
POOL SENTINELLEOVAL CONTOUR SYSTEM
Specific instruction sheet
Note : This instruction sheet manual includes installation instructions for
specific items related to the SENTINELLE OVAL pool. All the other steps must
be followed in the main instruction manual.
1- SUPPORT POSTS INSTALLATION
Insert the post base on the junction plate. Be sure that the plate hooks
are inserted in the post base openings. (figure 1.1)
Insert a 1 inch screw (Q) on each side of the post base
in the screw holes. (figure 1.2)
Insert the two tabs of the securing hook in the
openings on top of the post. The part must not be too
tight initially because it will need to be pulled out
when installing the liner. (figure 1.3)
When the liner is installed, re-install the
securing hook. A mallet could be necessary to insert it
tightly. After this step, the post should be lined up
against the wall. (figure 1.4)
Figure 1.3
Figure 1.1
Figure 1.2 Figure 1.4

2
2- TOP RAILS INSTALLATION
Position and place the top rails as indicated in figure 2.1. The top rail
must be pushed at the maximum to the inside of the pool to ease the future seat
caps installation. Insert the 1 inch screws (Q) and screw gently.
Even the space of each top seat ends to make sure it is centered between
the uprights.
When all the top rails are installed, fill the pool 2 feet from the top before
continuing to the other step.
Be sure that the two axis of the uprights are leveled by pushing gently
to the inside before tightening the screws permanently.
Install all necessary equipment (i.e. skimmer, filter, etc) per
manufacturers specifications.
Figure 2.1
3- SEAT CAPS, COLLARS AND BASE COVERS
INSTALLATION
Collar
Enlarge the collar to make sure that the
collar hooks can pass over the post. Insert
these hooks at the back of the post, right
underneath the top rail, in the openings
between the post and the wall. (figure 3.1)
Inserted in the round section posts only.
Base cover
The base cover is inserted the same way
as the collar. Enlarge and insert at the post
base. (figure 3.2) Inserted in the round
section posts only.
Figure 3.1
Figure 3.2

3
Seat cap
Insert the front part of the seat cap (outside of the pool) in the collar
opening. Push down to the back (inside of the pool) and snap on the top rail by
taking care of inserting the seat cap central rib in the post head slot. (figure 3.3
and 3.4)
Figure 3.3 Figure 3.4
4- PARTS LIST
Description Piece number 15x26 15x30 18x33 18x40 21x43
A- Top wall channel
(Round section)
15x26, 15x30 1071507160000 8 8 - - -
18x33, 18x40 1071807160000 - - 10 10 -
21x43 1072107160000 - - - - 10
B- Bottom wall channel
(Round section)
15x26, 15x30 1081502160000 8 8 - - -
18x33, 18x40 1081802160000 - - 10 10 -
21x43 1082102160000 - - - - 10
C- Top wall channel
(Straight side section)
Top wall channel 10707000042 4 6 6 10 12
D- Top transition channel *
(End of straight side section)
15’ 1071507000010 4 4 - - -
18’ 1071807000010 - - 4 4 -
21’ 1072107000010 - - - - 4
E- Bottom wall channel
(Straight side section)
Bottom wall channel 10802000042 4 6 6 10 12
F- Bottom wall channel transition
(End of straight side section) †
15’ 1081502000010 4 4 - - -
18’ 1081802000010 - - 4 4 -
21’ 1082102000010 - - - - 4
G- Steel wall
Steel wall (hole-to-hole) 109_ _ _ _ _ 0039_ _ 70’ 8” 77’ 8” 87’ 4” 101’ 4” 108’ 5”
H-Liner
Vinyl liner (hook) 1 1 1 1 1
Vinyl liner (overlap) 1 1 1 1 1
I- Plastic coping (not included)
Plastic coping 36” 6COP40000000 24 26 29 34 37

4
Description Piece number 15x26 15x30 18x33 18x40 21x43
J- Support post
Support post 102_ _ 0100_ _ 10 10 12 12 12
K- Top seat
Curved top seat 57” 101_ _010000 12 12 14 14 14
L- Seat cap
Seat cap 10300_ _E00 16 18 20 24 26
M- Collar
Collar 11900_ _E00 10 10 12 12 12
N- Securing hook
Securing hook 11800_ _E00 10 10 12 12 12
O- Base cover
Base cover 11700_ _E00 10 10 12 12 12
P- Bottom junction plate
Junction plate 10400_ _100 10 10 12 12 12
Q- 1” screw
Stainless screw 12 x 1” 2PPS121 116 128 144 168 180
R- Top seat
Straight top seat 29” 10100_ _E70 4 6 6 10 12
S- Upright cover
Upright cover 52” 102_ _000002 6 8 8 12 14
Upright cover 54” 102_ _000004 6 8 8 12 14
T- Logos
Logo Aqua Leader 130_ _000010 6 8 8 12 14
Logo plain 130_ _000000 6 8 8 12 14
U- Pressure plate
Steel pressure plate 2ANG042 6 8 8 12 14
V- Strap end channel
Steel strap end channel 2SEC000 6 8 8 12 14
W- Under channel
Steel under channel 2UCH000 6 8 8 12 14
X- Straps
Straps 15’ 2BDM015 9 12 - - -
Straps 18’ 2BDM018 - - 12 18 -
Straps 21’ 2BDM021 - - - - 28
Y- Washer 3 holes
Washer 3 holes 2PLA000 12 16 16 24 28
Z- Upright
Steel upright 52” 2REN200 6 8 8 12 14
Steel upright 54” 2REN400 6 8 8 12 14

5
Description Piece number 15x26 15x30 18x33 18x40 21x43
AA- Gussets
Right gusset 2GUR000 6 8 8 12 14
Left gusset 2GUL000 6 8 8 12 14
BB- Top plate
Metal top plate 2MTP000 6 8 8 12 14
CC- Top plate
Resin top plate 1040033E01 6 8 8 12 14
DD- Bottom plate
Resin bottom plate straight section 104_ _000000 6 8 8 12 14
EE- Bolt 5”
Bolt 5“ x 5/16 - 18 2PCB518 36 48 48 72 84
FF- Bolt 4 ½”
Bolt 4 ½” x 5/16 - 18 2PCB418 12 16 16 24 28
GG- Nut
Nut 5/16 - 18 2PNZ518 72 96 96 144 182
HH- Screw ½”
Screw ½” x 5/16 – 18 2PPS002 24 32 32 48 70
II- Screw ½”
Screw ½” #10 2PPS001 42 56 56 84 98
JJ- Screw ¾”
Screw ¾” #12 truss head 2TPS124 24 32 32 48 56
KK- Screw 1”
Screw 1” #10 2PPS004 24 32 32 48 56
LL- Bolt 5 ½” **
Bolt 5 ½” x ¼ - 20 2PCB520 6 8 8 12 14
MM- Nut **
Nut ¼ - 20 2PCB420 6 8 8 12 14
Piece number codification Color codes : 02=Pearl, 07 sand, 08 Ivory, 09 Champagne, 10 Green, 33 grey
*†The transition channels are the same type as the ones in the round section, but with
2 inches shorter. (Not illustrated)
** Used to hold the upright cover at the base (Not illustrated)

6
Exploded view
Round section
A
B
G
H
I
J
K
L
M
N
O
P
Q

7
Straight side section
O
C
E
R
S
T
HH
V
W
X
Y
AA
BB
CC
DD
EE
FF
GG
JJ
U
II
K
K
Z

8
Real sizes
AQUA LEADER reserves the right to modify or alter any construction specifications without
notice.
Manufactured by AQUA LEADER, 2370 de la Province Longueuil, QC,
J4G 1G1
REVISION 01/07