OBaby Munchy Highchair User manual

IMPORTANT KEEP FOR FUTURE REFERENCE
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE
USING THIS PRODUCT
Munchy Highchair
Instruction Manual

Thank you for choosing Obaby. To ensure that your highchair is used in accordance with
these instructions, please read them fully.
This highchair conforms to BS EN 14988:2006 and is guaranteed for 6 months from the
date of purchase against manufacturing defects. If, however you have any problems,
please contact your Obaby retailer from whom you purchased your product, who will take
appropriate action.
Your child’s safety may be affected if you do not follow these instructions.
WARNING: A child’s safety is your responsibility
WARNING: Do not use the highchair unless all components are
correctly tted and adjusted. Ensure that all locking devices are
engaged before use
WARNING: Only use on a stable, level surface
WARNING: Do not leave the child unattended
WARNING: The child should be clear of moving parts while making
adjustments or opening or folding the highchair. Risk of serious
injury (entrapment, laceration or amputation) exists
WARNING: Children should be harnessed in at all times. Always use
the crotch strap in combination with the waist belt
WARNING: Be aware of the risk of open re and other sources of
strong heat, such as electric bar res, gas res, etc. in the near
vicinity of the highchair
WARNING: Do not use the highchair if any part is broken, torn or
missing and use only spare parts approved by the manufacturer
• Do not use this highchair until the child can sit unaided
• Do not move the highchair with your child inside
• Do not allow your child to climb unassisted into, play with or hang onto the
highchair. This is not a toy.
• This highchair requires regular maintenance by the user
• Overloading, incorrect folding and the use of non approved accessories may
cause damage or break the highchair
• This highchair is intended to carry one child from when the child can sit
unaided and up to a maximum weight of 15kg, discontinue use if your child is
able to climb out
• When folded, store away from children
ROUTINE CARE & MAINTENANCE
- For cleaning, use only a mild detergent and warm water
- DO NOT USE BLEACH
- DO NOT USE any abrasive substances
- From time to time, check your highchair for loose screws, worn parts, torn
material or stitching. Replace or adjust the parts as needed.
Due to constant updating and improvements, some components may occasionally differ slightly from
the images shown in these instructions. We reserve the rights to change the specications of any
products without prior notice. If you need any assistance please contact your Obaby retailer from
whom you purchased your product, who will take appropriate action.
Safety Warnings Getting to know your Highchair
Tray
Seat unit
Harness
Front leg
Seat back
support bar
Back leg
2
3
www.obaby.co.uk
www.obaby.co.uk

Fitting the Legs
Press
The front and rear legs are a different width. Please be aware that the rear leg is
narrower at the top, than the front leg (g.7).
Push the front leg a little way into the seat frame tubes at both sides evenly (g 8 & 9).
Push in the spring buttons (g.10), continuing to push the legs until the buttons click into
place in the holes (g.11 & 12).
Repeat this process until each leg is tted securely.
The t of the legs in the frame is very tight for added security. Do not force the legs into
position, but apply an even and constant pressure.
Should the highchair need to be taken apart, gently push in the spring buttons and
evenly ease out the leg assemblies.
g. 7
g. 10
g. 8
g. 11
g. 9
g. 12
Fitting the Seat Back
Unclip the press-studs on either side of the Highchair as shown (g.1).
Slide the curved part of the seat back support bar into the fabric pocket on the seat back,
whilst the highchair is still folded (g.2 & 3).
Slide the two ends of the seat back support bar into the seat frame tubes (g.4) and
push in the spring buttons (g.5). Continue to push the frame together until the buttons
click into place in the holes on the tubes (g.6).
Secure the seat into position by re-clipping the press-studs onto the frame as shown
(g.1).
g. 1
g. 4
g. 2
g. 5
g. 3
g. 6
Press “Click”
“Click”
4
5
www.obaby.co.uk
www.obaby.co.uk

Folding your Highchair
To fold your highchair, unfasten the press-stud underneath the tray (g.19) and unclip
the tray from the frame by lifting the tray (g.20).
Lift the tray above the seat (g.21) and fold the legs together (g.22). Then lower the
tray (g.23 & 24).
Unfolding your Highchair
To unfold your highchair, lift the tray above the seat and pull apart the legs (g.13).
On either side of the seat, fasten the seat sides to the frame using the press-studs
(g.14) (this will only need to be performed once).
Lower the tray down onto the front frame (g.15) and push the tray and frame together
until it clicks into place (g.16).
Secure the tray using the strap and press-stud (g.17 & 18).
g. 13 g. 19
g. 16 g. 22
g. 14 g. 20
g. 17 g. 23
g. 15 g. 21
g. 18 g. 24
Press Lower
Lower Lift
WARNING: Ensure that all locking devices are engaged before use.
The child should be clear of moving parts while making adjustments or opening or
folding the highchair. Risk of serious injury (entrapment, laceration or amputation)
exists.
“Click”
6
7
www.obaby.co.uk
www.obaby.co.uk

To fasten the harness, insert both fasteners on the waist strap into the clasp on the
crotch strap (g.25) and clip each chest strap onto the waist strap (g.26 & 27).
To release the harness, squeeze each of the clips in the centre of the harness and pull
away from the clasp, one at a time (g.28).
Adjust the harness length using the buckles on each strap (g.29).
g. 25
g. 28
g. 26
g. 29
g. 27
Using the Harness
Press
WARNING: Ensure the harness is correctly tted before use. The harness should
always be adjusted to t correctly. Children should be harnessed in at all times.
Always use the crotch strap in combination with the waist strap.
8
www.obaby.co.uk