Octane Fitness LX8000 Parts list manual

ASSEMBLY & OPERATIONS INSTRUCTIONS
LX8000 WIRELESS AUDIO KIT
(800MHz or 900MHz)

1
LX8000 WIRELESS AUDIO KIT CONTENTS
 LX8000 Wireless Audio Keypad LX8000 Wireless Audio Console
 Assembly and Operations Instructions
ASSEMBLY & OPERATIONS INSTRUCTIONS
LX8000 WIRELESS AUDIO KIT
(800MHz or 900MHz)
 800MHz or 900MHz Receiver Cable
 Audio Jack Assembly
 Audio Cable Heart Rate Cable
Console Box Contents:
 Console Hardware
*Hardware illustrated to scale; not actual size.
1
7
9
0
2
4
3
5
6
8
PAUSE
CLEAR
CHOOSE
WORKOUT
SELECT
ENTERTAINMENT
ADJUST
SETTINGS
Enter Level
Disp
Lock
BOOST
WORKOUT
1
2
3
4Channel Volume
MUTE
Lateral
Width
OR
Quick Start Program
Workout Enter
C-1
C-4
C-2
C-3
#2 Phillips
#2 Phillips
 900MHz (800MHz) Receiver

2
B. Wireless (800MHz/900 MHz) Receiver
Route receiver cable down through mast and
out the bottom of the mast (not pictured).
Center the receiver on the user side of
the frame bar that is between the moving
handlebars, making sure the wire antenna is
on the top of the receiver. Insert cable tie C-4
(Qty 2) through holes in receiver bracket and
secure bracket to frame.
Connect audio jack cable and receiver cable
to receiver. Secure loose cable to side of
frame bar with cable tie C-4 (Qty 2).
Remove slack from audio jack cable and
secure under keypad plate with cable tie C-3
(not pictured).
LX8000 WIRELESS AUDIO KIT ASSEMBLY INSTRUCTIONS
A. Audio Jack
Remove bottom screw from water bottle
holder.
Connect audio cable to audio jack assembly
(not illustrated).
Loosen screws on audio jack assembly; place
assembly over mast plate; tighten screws.
Secure with screw to water bottle holder.
Remove upper left screw from water bottle
holder; insert C-1(Qty 1) through C-3 (cable tie);
re-attach to water bottle holder and tighten
screw. (Do not cable tie audio cable at this
time.)
Route audio cable down through hole under
keypad plate and out the bottom of the mast.
Complete these instructions during initial assembly of the LX8000 elliptical, after mounting the keypad on the
mast. For a fully-assembled LX8000, remove the top covers, console, keypad and CSAFE cable (connected to
CSAFE port on console back--see diagram on page 3), then complete these instructions. *Retain all screws
for use in this assembly.




Cables
not
shown



Cables
not
shown

3
C. Keypad
Connect keypad cables per diagram on keypad;
attach keypad to mast plate with C-2 (Qty 4).
D. Console
Attach console and console arcs to mast plate
with C-1 (Qty 4) (not shown).
Match cable connectors (Qty 7) to sockets
on console back; connect. Note: White 8-pin
socket on console back and audio jack are not
used for 900MHz (800MHz) installation.
Attach cable cover to mast plate (not shown.)
E. User Settings
Pedal the unit to activate the keypad for
programming.
Press and hold Level /to display
programming options.
PressEnter toviewsettingoptionsasdescribed
on following page; press to select option and
move to next setting. (Factory setting shown in
BOLD.) Navigate to “900MHz Channels” and
follow the instructions to complete console
programming for your environment.
Press Enter when “Exit” is displayed to save
selections. Press Pause Clear twice to exit
without saving changes.
I. Complete Installation
Replace shrouds, or return to LX8000 Assembly
Instructions to complete assembly of new unit.
Fan
(white, 2-pin)
Heart Rate
(white, 3-pin)
Console Ground
(metal; green wire)
900MHz Receiver/C-SAFE
(white, 5-pin)
Console to Base
(white, 14-pin)
Handlebar Control
(white, 6-pin)
Keypad
(black, 14-pin)

Keypad
(white, 14-pin)
Console to Base
(white, 14-pin)
Fan
(white, 2-pin)
Heart Rate
(white, 3-pin)
Console Ground
(metal; green wire)
Handlebar Control
(white, 6-pin)
900MHz Receiver/C-SAFE
(white, 5-pin)
Unused
(audio jack)
Unused
(white, 8-pin)

Reserved for
Software Update
(black)
1
7
9
0
2
4
3
5
6
8
PAUSE
CLEAR
CHOOSE
WORKOUT
SELECT
ENTERTAINMENT
ADJUST
SETTINGS
Enter Level
Disp
Lock
BOOST
WORKOUT
1
2
3
4Channel Volume
MUTE
Lateral
Width
OR
Quick Start Program
Workout Enter
PRESS AND
HOLD
VIEW OPTIONS
EXIT AND SAVE
EXIT
WITHOUT
SAVING
Press ANY

to SELECT SETTING


4
USER SETTINGS
Warm-Up Controls 3-minute warm-up: ON or OFF
Clock
Direction
Controls clock counting: UP or DOWN
Max
Workout
Time
Sets limit for workout time: 1 to 99 minutes (factory-set at 30:00). Press Enter to scroll in
15-minute increments, or enter value using number keypad.
Unit Type Controls weight and distance display units: ENGLISH (pounds and miles) or METRIC
(kilograms and kilometers)
CROSS
CiRCUIT
Activates the CROSS CiRCUIT Pro programs: ON or OFF.
Default
Width
Defines default setting for lateral width: 1 to 10 (factory-set at 5). Press enter to scroll through
values or enter value using number keypad.
900MHz
(800MHz)
Channels
Initiates channel programming; press Enter to begin. Press CH ()to select the appropriate
program modes for your facility:
P-1 = MYE Entertainment 900MHz (800MHz) transmitters
P-2 = Cardio Theater LCS 900MHz (800MHz) transmitters
P-3 = Cardio Theater / Enercise x TV 900MHz (800MHz) transmitters
P-4 = BroadcastVision 900MHz (800MHz) transmitters
To automatically scan and program channels:
With the proper transmitter mode displayed, press Enter to auto-scan and lock
transmitters. Repeat as needed for each transmitter type.
Press CH () or CH () to verify that “PRESET” appears in the display, indicating that all
transmitters have been locked in.
Press MUTE to save 900MHz (800MHz) CHANNELS and return to user settings.
To manually program channels:
With the proper transmitter mode displayed, press MUTE.
Press CH () or CH () to scroll through all transmitter channels.
To add or delete a transmitter channel press Enter. NOTE: “PRESET” will appear in the
display when a transmitter channel is programmed.
To exit manual program mode press the MUTE button. The display will blink briefly and
will default to first transmitter channel programmed.
Use the CH () or CH () to select another transmitter type (P-1 to P-4) as needed and
repeat these manual steps.
Press MUTE to save 900MHZ (800MHZ) CHANNELS and return to user settings.
900MHz
(800MHz)
Near/Far
Sets the reception sensitivity of the 900MHz (800MHz) receiver, FAR (for most installations)
or NEAR (when receiver is installed 1-5 feet from a transmitter). Press Enter to switch from
one setting to the other. The Message Center displays the revised setting for 5 seconds,
then returns to 900 MHZ (800mhz) NEAR/FAR.
Beep Controls console sounds: ON or OFF.
Brightness Controls brightness of the console LEDs: 1 (dim) to 8(bright).
Exit Press Enter to Exit and save settings. Press Pause Clear twice to exit without saving.

5
900MHz (800MHz) Keypad Buttons
The table below describes the buttons controlling wireless
audio functions on the LX8000. Refer to LX8000 Operations
Manual for descriptions of the elliptical programming buttons on
the keypad.
Mute Turn TV audio on/off.
VOL (/)Increase/decrease audio volume.
Note: When the user stops pedaling for 10 seconds or the console is
reset, the volume control is automatically reset to level 2.
(VOL ()is also used to program 900MHz (800MHz) NEAR/FAR in User
Settings.)
CH (/)Move backward ()or forward () through the 900MHz (800MHz)
channels programmed for your facility.
Learn More at www.octanefitness.com
Log on to www.octanefitness.com for additional information about product features and answers to many common
questions and tips on using your elliptical. If you would like to speak to an Octane Fitness Customer Service
specialist, please call 1-888-OCTANE4 or 763-757-2662, extension 1.
Channel Volume
MUTE

6
NOTES

FUEL YOUR LIFE™
Octane Fitness Octane Fitness International
US & Canada, Latin America, Asia & Asian Pacific Europe, Middle East, Africa
7601 Northland Drive North Rivium Westlaan 19
Suite 100 2909 LD, Capelle a/d Ijssel
Brooklyn Park, MN 55428 The Netherlands
Phone: 888.OCTANE4 (US and Canada) Phone: [phone]
763.757.2662 (Latin America, Asia and Asian Pacific) Fax: [phone]
Fax: [phone]
©2012 Octane Fitness, LLC. All rights reserved. Octane Fitness, LateralX and Fuel Your Life are registered trademarks of Octane Fitness. Any use of
these trademarks, without the express written consent of Octane Fitness, is forbidden.
106974-001 REV B
Are you passionate about your workout and the results?
Share your story with others on the Octane Fitness web site.
Go to: www.octanefitness.com/testimonials
Then click on “Share My Story” and
show the world how fueled you are.
www.octanefitness.com
www.youtube.com/user/octanefitness
www.facebook.com/octanefitness