ODROID Vu8S User manual

2023/09/09 21:46 1/4 ODROID-Vu8S
ODROID Wiki - https://wiki.odroid.com/
ODROID-Vu8S
The ODROID-Vu8S is dedicated to ODROID-M1S. It can only be used via a MIPI DSI Connector(J7) on
M1.
It has a 8inch multi-touch screen.
The I Bracket PCB is required to dock Vu8S to ODROID-M1S.

Last
update:
2023/08/29
15:57
inernal:odroid-m1s:application_note:software:display_vu8s https://wiki.odroid.com/inernal/odroid-m1s/application_note/software/display_vu8s
https://wiki.odroid.com/ Printed on 2023/09/09 21:46
Software Setting
Software Setting
Specifications
8-inch TFT-LCD
Portrait 800(H) x 1280(V) pixels hardware native resolution
Mechanical Dimensions : 202(W) x 153.0(H)
Viewable screen size : 172.224 x 107.64 mm (active area)
5 finger capacitive touch input
Power consumption : 2.4W ± 10% (100% duty cycle)
Physical Dimensions
Mechanical drawings (DXF format)
vu8m_blacket.dxf.zip
Mechanical drawings (3D Step format)
vu8m_mba_lcd_step.zip

2023/09/09 21:46 3/4 ODROID-Vu8S
ODROID Wiki - https://wiki.odroid.com/
Mechanical drawings (DXF format)
vu8m_u_blacket.dxf.zip
Assembly
Package includes
A. Assembled 8inch TFT LCD + multi touch screen * 1EA
B. M3 x 7(BLACK) Bolt * 7EA including a spare part
C. LCD Bracket Board for M1S * 1EA with I form Bracket Board for M1S * 2EA

Last
update:
2023/08/29
15:57
inernal:odroid-m1s:application_note:software:display_vu8s https://wiki.odroid.com/inernal/odroid-m1s/application_note/software/display_vu8s
https://wiki.odroid.com/ Printed on 2023/09/09 21:46
Assembly guide
Please take special care when assemble it.
1. 2.
Mount the two U
Form Bracket boards
on the back of the
M1.
Two PM3.0x7 bolts
are fastened to the
two U Form Bracket
boards on the M1,
respectively.
Mount the U
Form Bracket
board with the
M1 on the back
of the 8“ LCD
module.
Fix it with 4 x
PM3.0x7 bolts.
3. 4.
Plug and fix the 31pin
60mm FPCB cable of
MIPI CONVERTER on
the ODROID-M1
The LCD and Touch
signals goes to the
converter board via
this FPCB.
You will need to
carefully undo the
clamp before
inserting the cable.
Make sure to press
the clamp in to
secure the ribbon in
place.
Check the two 31pin
and 6pin FPCB cables
connection.
LCD : 31pin / 60mm
Touch screen : 6pin /
3.5mm
Mount the M3*40
Support and
PM3.0x7 BOLT to
the bottom of the
U form Bracket
Board
the angle of
Vu8M can be
adjusted up to 70
degrees.
From:
https://wiki.odroid.com/ - ODROID Wiki
Permanent link:
https://wiki.odroid.com/inernal/odroid-m1s/application_note/software/display_vu8s
Last update: 2023/08/29 15:57