OEM Tools 24859 Service manual

UNPACKING
After unpacking unit, inspect carefully for any damage
that may have occurred during transit. Check for loose,
missing, or damaged parts. If any damage is observed, a
shipping damage claim must be filed with carrier. DO NOT
use the OEMTOOLS®Air Hydraulic Motorcycle Lift 1,000
Lb. Capacity if broken, bent, cracked or damaged parts
(including labels) are noted. Any Motorcycle Lift that appears
damaged in any way, operates abnormally, or is missing
parts should be removed from service immediately. If you
suspect that the Motorcycle Lift was subjected to shock
load (a load that was dropped suddenly, unexpectedly, etc.),
immediately discontinue use until it has been checked by a
factory authorized service center.
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and
others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal
injury and/or damage to product or property. Please retain instructions for future reference.
The following safety information is provided as a guideline to help you operate your Motorcycle Lift under the safest possible
conditions. Any tool or piece of equipment can be potentially dangerous to use when safety or safe handling instructions are
not known or not followed. The following safety instructions are to provide the user with the information necessary for safe
use and operation. Please read and retain these instructions for the continued safe use of your Motorcycle Lift. Failure to
follow instructions listed below may result in serious injury. In addition, make certain that anyone who uses the equipment
understands and follows these safety instructions as well.
Operating Instructions and Parts Manual 24859
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
[email protected]
Thank you very much for choosing an OEMTOOLS®Product!
For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:
Model: _______________ Purchase Date: ___________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product
before you begin using it. This product is designed for certain applications only. OEMTOOLS®cannot be responsible for issues
arising from modification. We strongly recommend that this product is not modified and/or used for any application other than that
for which it was designed. If you have any questions relative to a particular application, DO NOT use the product until you have first
contacted customer service to determine if it can or should be performed on the product.
Explanation of Safety Signal Words
WARNING:Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION:Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION:Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTES:Provide clarity and helpful information.
AIR HYDRAULIC MOTORCYCLE
LIFT 1,000 LB. CAPACITY
1
24859
WARNING
8/19
2019 OEMTOOLS®

2
Operating Instructions and Parts Manual 24859
8/19
2019 OEMTOOLS®
AIR HYDRAULIC MOTORCYCLE LIFT
1,000 LB. CAPACITY
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your product. Read this manual carefully. Learn
the product’s applications and limitations, as well
as potential hazards specific to it. The use of this
product is simple and straightforward if you follow the
instructions. When operating this product, use common
sense and only use this product for its intended
purpose.
2. Maintain labels and nameplates on this product. These
carry important information. If unreadable or missing,
contact OEMTOOLS®for a replacement.
3. Maintain this product with care. Keep it dry and clean –
and free from brake fluid, oil, and grease (if applicable).
4. Check for damage. Check your product regularly. If
part of the product is damaged, it should be carefully
inspected to make sure that it can perform its intended
function correctly. If in doubt, the part should be
repaired. Refer all servicing to a qualified technician.
Consult your dealer for advice.
5. Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the product’s operation.
6. DO NOT use a damaged product. Tag damaged
products “DO NOT USE” until repaired. If damaged,
have the product serviced before using. Many
accidents are caused by poorly maintained products.
7. Service must be performed only by qualified repair
personnel. Service or maintenance performed by
unqualified personnel could create a risk of injury.
8. When servicing a product, use only identical
replacement parts. Use of unauthorized parts or failure
to follow maintenance instructions could create a risk
of injury.
9. Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one product may become hazardous when
used on another product.
10. Keep work area clean and well lit. Cluttered or dark
work areas invite accidents.
11. Maintain a safe working environment. Keep the work
area well lit. Make sure there is adequate surrounding
workspace. Keep the work area free of obstructions,
grease, oil, trash, and other debris. DO NOT use this
product in a damp or wet location.
12. Keep children away. All children should be kept away
from the work area. Never let a child handle this
product without strict adult supervision.
13. Store this product out of the reach of children and
untrained persons. This product may be dangerous in
the hands of untrained users.
14. DO NOT operate this product if under the influence of
alcohol or drugs. Read warning labels on prescriptions
to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, DO NOT
attempt to operate.
15. Use safety equipment. Eye protection should be worn
at all times when operating this product. Use ANSI
approved safety glasses. Everyday eyeglasses are NOT
safety glasses. Dust mask, non-skid safety shoes, hard
hat or hearing protection should be used in appropriate
conditions.
16. Wear proper apparel. Loose clothing, gloves, neck-ties,
rings, bracelets or other jewelry may present a potential
hazard when operating this product. Keep all apparel
clear of the product.
17. DO NOT overreach. Keep proper footing and balance
at all times when operating this product.
18. Keep away from flammables. DO NOT attempt to
operate this product near flammable materials or
combustibles. Failure to comply may cause serious
injury or death.
19. Avoid accidental fire and/or explosion. DO NOT smoke
near engine fuel and battery components.
20. We believe the information contained herein to be
reliable. However, general technical information is given
by us without charge and the user shall employ such
information at their own discretion and risk. We assume
no responsibility for results or damages incurred from
the use of such information in whole or in part. Always
refer to specific instructions and technical information
supplied by vehicle manufacturer.
21. The manufacturer declines any and all responsibility
for property damage or injury if said damage is the
result of unskillful handling by the operator or of
failure to observe the basic safety rules set forth in the
instruction manual.
22. The warnings, precautions, and instructions discussed
in this manual cannot cover all possible conditions
and situations that may occur. The operator must
understand that common sense and caution are factors
which cannot be built into this product, but must be
supplied by the operator.
PRODUCT DESCRIPTION
The OEMTOOLS®24859 Air Hydraulic Motorcycle Lift
can lift motorcycles (up to 1,000 lbs.) to nearly 30" with
the convenient pump pedal or when connected to shop
air for even quicker lifting. This motorcycle lift is great for
maintenance or repair of most motorcycles.
PRODUCT SPECIFICATIONS
Capacity 1,000 Lbs. (453.6 Kg)
Min. Height 7" (177.8 mm)
Max. Height 29.5" (749.3 mm)
Platform Dimensions 86.5" x 26.75" (219.7 cm x 67.95 cm)
Recommended 120-150 PSI
Air Pressure
Air Inlet Fitting 1/4"

3
Operating Instructions and Parts Manual 24859
8/19
2019 OEMTOOLS®
AIR HYDRAULIC MOTORCYCLE LIFT
1,000 LB. CAPACITY
CONTENTS
Qty Part Qty Part
1
Main Lift Assembly 1 Release Pedal
2 2 Front Casters 1 Cover Plate
2 2 Rear Wheels 1 Wheel Clamp
1 Hardware Kit 1 Lock Bar
1 Pump Pedal 1 Ramp
SPECIFIC SAFETY INSTRUCTIONS
AND WARNINGS
Thoroughly read and understand all instructions in this
product manual before using this product. Failure to
follow all instructions listed below may result property
damage and/or serious personal injury.
WARNING:
1. DO NOT exceed the rated capacity of the motorcycle
lift.
2. DO NOT attempt to transport a motorcycle on the lift.
The lift is only used in a static position for lifting and
lowering loads. Ensure that the motorcycle is stable
before lifting, lowering or working on the motorcycle.
3. DO NOT make any modifications to the lift.
4. DO NOT tamper with or adjust safety valve.
5. Use only on hard, level surfaces.
6. Use this motorcycle lift only for its intended purpose.
7. Always position the motorcycle completely onto the
platform. DO NOT use the ramp to support any portion
of the motorcycle while lifting.
8. Before lifting, ensure that the weight of the motorcycle
has been fully supported by the lift platform.
9. Always center load on lift platform.
10. Use only appropriately rated straps to secure the
motorcycle on the platform before lifting.
11. Immediately after lifting load, ensure lift locking bar is
inserted and secure.
12. Before moving, lower the lift to the lowest point.
13. Wear ANSI approved safety glasses and work gloves
during use.
14. Keep clear of load while lifting and lowering.
15. Always lower lift platform slowly.
16. Inspect before every use. DO NOT use if parts are
loose or damaged.
ASSEMBLY
1. Attach the 2 Rear Wheels (44) onto the chassis using
the Washer (43) and Cotter Pin (31)
2. Attach the 2 Front Casters (14) onto the chassis using
the Bolt (12), Washer (13), Lock Washer (20) and Nut
(21).
3. Attach the Release Pedal (10) to the Release Valve
Spindle (5).
4. Attach the Pump Pedal (11) to the Pump Spindle (9).
5. Raise the motorcycle lift to an appropriate height and
insert the Safety Bar (22) into the holes on the lifting
arm. Install Wheel Clamp Assembly (55).
6. Insert U-Bolt Tie Downs (42) onto the Lifting Table (35)
and attach them using Nuts (33).
7. Connect the Ramp (37) to the Lifting Table (35) using
Washer (23) and R Pin (4).
8. Install the Cover Plate (36) onto the Lifting Table (35).
BEFORE FIRST USE
1. After assembly, wait for one hour to allow the oil in the
pump to settle before purging air from the system.
NOTE:Failure to allow sufficient time for the oil to settle could
result in air remaining in the oil. In this event, the pump will not
purge completely the first time and a second purge will be
required.
2. Connect the male quick coupler fitting into the air
supply hose female quick coupler. Then fully depress
the Release Pedal (10). Actuate the air valve letting the
pump work for 20 seconds to eliminate any air in the
hydraulic system.
3. Test the lift by raising it to full height and then lowering
it. Depress Release Pedal (10) slowly to control the rate
of descent.
OPERATION
4. Adjust the Leveling Supports (18) down to raise the
casters off the ground to prevent the lift from moving.
5. Push the motorcycle up the ramp and onto the
platform.
NOTE:Multiple mounting holes in the platform allow the vise
to fit a variety of motorcycles.
1. Clamp the front wheel in Wheel Clamp Assembly (55)
to prevent any movement of the motorcycle.
2. Strap the motorcycle securely to the platform using the
U-bolt Tie Down (42) locations.
3. With the quick coupler connected to your air supply
hose, actuate the air valve to raise the lift. When air
source is not available, pump the lift Pump Pedal (11)
to raise the lift.
4. When the platform has been raised to the working
height, shut the air valve (or stop pumping) and insert
the Safety Bar (22) through the holes in the front Lifting
Arm (38) so that the lift cannot be accidently lowered.
5. Before lowering, check under the lift to ensure that
there are no obstructions and that it is safe to lower
the unit. Remove the Safety Bar (22) and then SLOWLY
press the release foot pedal to GENTLY lower the lift.
NOTE:Multiple mounting holes in the platform allow the vise
to fit a variety of motorcycles.
6. When the lift is fully lowered, unstrap the motorcycle,
open the vise jaws and remove the motorcycle from the
lift.

4
Operating Instructions and Parts Manual 24859
8/19
2019 OEMTOOLS®
AIR HYDRAULIC MOTORCYCLE LIFT
1,000 LB. CAPACITY
CARE AND MAINTENANCE
1. When not in use, the lift must be stowed in the lowest
position in a dry location to minimize ram and piston
corrosion.
2. Keep the lift clean and wipe off any oil or grease.
Lubricate all moving parts.
3. Periodically check the ram and piston for signs of
corrosion. Clean exposed areas with a clean, oiled
cloth.
4. Before each use, check all parts. If any part of the lift is
damaged (or suspected to be damaged), remove the lift
from service and take necessary action to repair.
5. If the lift efficiency drops, purge air from the hydraulic
system by fully depressing the Release Pedal (10)
and actuating the air valve allowing it to pump for 20
seconds to eliminate any air in the hydraulic system.
6. Check the hydraulic oil level. If the oil level is low,
remove the filler plug on the pump and add hydraulic
oil as necessary. DO NOT use brake fluid or any other
improper fluid. Use only a high quality hydraulic jack oil.
To check the oil level, please use the following procedure
– it is recommended to have several people present to
perform this operation
1. Raise the platform to a working height. Carefully raise
the front of the lift while another person places a
sturdy 7" block under the base frame where the 2 front
casters are located.
CAUTION:Be sure that the person assisting is clear of
the lift before lowering onto the block.
2. Lower the lift completely with the block underneath the
lift. By placing the block under the frame, the pump
should now be in a horizontal position as shown in
Figure 2.
3. Remove the Cover Plate (36) and then remove the Oil
Plug (P28 in Figure 1).
FIGURE 1
4. The oil level should be even with the top surface of the
cylinder (at horizontal position) right below the filler plug
hole. (Figure 2)
5. If the oil level is low, add quality hydraulic oil as
necessary to reach the top of the cylinder. DO NOT use
brake fluid.
FIGURE 2
DISPOSAL
At the end of the useful life of the motorcycle lift, dispose
of the components according to all local, state, and
federal regulations.

5
Operating Instructions and Parts Manual 24859
8/19
2019 OEMTOOLS®
AIR HYDRAULIC MOTORCYCLE LIFT
1,000 LB. CAPACITY
PARTS DIAGRAM

6
Operating Instructions and Parts Manual 24859
8/19
2019 OEMTOOLS®
AIR HYDRAULIC MOTORCYCLE LIFT
1,000 LB. CAPACITY
Figure Description Qty.
1
Pump 1
2 Link 1
3 Pin 1
4 R-pin 5
5 Release Valve Spindle 1
6 Link 1
7 Pin 2
8 Axle 2
9 Pump Spindle 1
10 Release Pedal 1
11 Pump Pedal 1
12 Bolt 8
13 Washer 9
14 Front Caster 2
15 Bolt 4
16 Washer 8
17 Bushing 4
18 Leveling Supports 2
19 Saddle 1
20 Lock Washer 9
21 Nut 9
22 Safety Bar 1
23 Washer 12
24 Bolt 10
25 Lock Washer 8
26 Nut 8
27 Spring 1
28 Bushing 4
29 Bolt 4
30 Nut 10
31 Cotter Pin 2
32 Stop Tube 1
33 Nut 16
34 Screw 24
35 Lifting Table 1
36 Cover Plate 1
37 Ramp 1
PARTS LIST
Figure Description Qty.
38 Lifting Arm 1
39 Lifting Arm 1
40 Screw 1
41 Bolt 1
42 U-Bolt Tie Down 4
43 Washer 2
44 Rear Wheel 2
45 Screw 1
46 Chassis 1
47 Bolt & Washer Assembly 2
48 Axle 1
49 Sliding Clamp 1
50 Fixed Clamp 1
51 Rubber Pad 2
52 Rubber Pad 2
53 End Cap 4
54 Bolt 4
55 Wheel Clamp Assembly 1
56 Inner Tube 1
57 End Cap 2
58 Ring 1
59 Pin 1
60 Snap Ring 2
61 Snap Ring 2

7
Operating Instructions and Parts Manual 24859
8/19
2019 OEMTOOLS®
AIR HYDRAULIC MOTORCYCLE LIFT
1,000 LB. CAPACITY
NOTES:

8
Operating Instructions and Parts Manual 24859
8/19
2019 OEMTOOLS®
AIR HYDRAULIC MOTORCYCLE LIFT
1,000 LB. CAPACITY
CONTACT US
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: [phone]
www.oem-tools.com
OEMTOOLS®ONE YEAR WARRANTY
For up to one year from the date of purchase of this OEMTOOLS®product, if you find any defect in material or
workmanship (through normal usage), return it to the place of purchase or to OEMTOOLS®for repair or replacement at
our discretion. In order to obtain this service, send the product and proof of purchase (transportation pre-paid) to:
OEMTOOLS®Q.A. Dept, 3580 E. Raines Road #3, Memphis, TN 38118.
We will not be responsible for lost or damaged goods during transportation; please insure your package. If our
inspection verifies the defect, we will either repair or replace the product, or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if
we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you
must bear the cost of returning the product.
OEMTOOLS®does not provide warranty for products labeled other than OEM®or OEMTOOLS®. OEMTOOLS®will
not provide any warranty for products subjected to abnormal use. Abnormal use includes (but is not limited to) abuse,
accident, alteration, neglect, and unauthorized or unreasonable use or repairs. This warranty does not cover bits,
blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or replace blades, bits,
files, and batteries as necessary. OEMTOOLS®reserves the right to make any changes in construction or design at any
time without any obligation in incorporating such changes to tools or equipment previously sold.
OEMTOOLS®makes every effort to ensure that its products meet high quality and durability standards, and warrants
to the original purchaser that this product is free from defects in materials and workmanship for the period of one
year from the date of purchase. This warranty does not apply to damage due directly or indirectly to misuse, abuse,
negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear
and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or
consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may also have other rights,
which vary from state to state.
Don’t forget to register your new OEMTOOLS®product at www.oem-tools.com.