OEM NSB-200AT User manual
INSTRUCTION MANUAL
Fan Heater
Model: NSB-200AT
Thank you very much for purchasing our products, please read this manual and instruction carefully before
using.
IMPORTANT SAFETY INSTRUCTIONS:
1. Read all instructions carefully before using.
2. Make sure use the rated voltage 120V
3. Do not operate this appliance if the cable or plug becomes damaged.
4. Keep the appliance and cable away from sources of heat, sharp objects or anything that may cause
damage.
5. Repair malfunction machine or damaged cable only by authorized service representative. If the
supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
6. Ensure the appliance is switched OFF before connecting to the mains power supply.
7. Switch off the power supply and unplug from the mains socket when not in use, before cleaning or
changing accessories.
8. Do not install the heater right below a socket.
9. To prevent overload and blown fuses, do not plug other appliance into same outlet (receptacle)
10. Do not place the heater on carpets, don’t place the cable under carpets. Arrange cord away from
traffic areas so that it will not be tripped over.
11. Indoor use only.
12. NEVER use this heater where it may come into contact with water i.e. bathroom, shower room,
kitchen.
13. Never leave the appliance unattended when connected to the mains power supply.
14. Children should be closely supervised at all times when they are near any electrical appliance.
15. Do not cover. NEVER use the heater to dry clothes or similar articles
16. Don’t touch the hot surfaces.
17.Do not position the appliances in close proximately to curtains or other combustible materials.
Keep combustible material such as furniture, cushions, bedding, paper, clothes, curtains etc. at least
1.0m away from the heater.
18. Always ensure that hands are dry before operating or adjusting any switch on the product or
touching the plug and mains supply connections.
19. Do not use the appliances with a programmer, timer or any other devices that switches the
appliances on automatically.
20.To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft
surfaces, like a bed, where openings may become blocked.
21. Do not store away until the heater cools down, store the heater in cool dry location when not in
use.
22. Don’ t use extension cable
23. Always operate on a flat horizontal surface.
24.Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may
cause an electric shock, fire or damage to the appliance.
25.Do not operate in areas where gasoline, paint or other flammable liquids are used or stored.
26. The most common cause of overheating is deposits of dust or fluff in the appliance. Ensure these
deposits are removed regularly by unplugging the appliance and vacuum cleaning air vents and
grilles.
27. Always use the heater in an upright position.
28.Do not use the appliance in rooms less than 4m2area.
29. To disconnect the appliance, switch it “OFF”, then remove the plug from outlet. Do not pull out
the cord because this could damage it.
30. This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Heat setting:
The fan heater incorporates a rotate on switch you can select the different air by turning the switch
clockwise to:
O OFF
* FAN
I WARMAIR (1000W)
II WARMAIR (2000W)
THERMOSTAT:
When the convector is switched on:
1.Turn the thermostat knob in a clockwise direction to the max position.
2.Once the room temperature has reached the desired temperature, turn the thermostat knob slowly
in an anti-clockwise direction until a "click" sound is heard. That is the setting temperature. Now, the
convector is switched off and the indicator lights off.
3.The convector will automatically maintain the set temperature. It will switch on when the room
temperature is below and switch off if above the setting.
4.The red indicator show that the convector is switched on.
SAFETY DEVICE
This appliance is provided with two safety devices which will switch off the heater in case of
accidental overheating. To reset, disconnect the plug from the power for a few minutes, remove the
cause of overheating, then plug the appliance in again. If it still cannot be reset, ask a qualified
technician to check and repair.
MAINTENANCE:
The fan heater only needs regular cleaning on the outside.
Before you clean the unit, turn the switch to OFF. Remove the plug from socket and wait until the
fan heater cools down.
Use a damp cloth to wipe the heater housing.
Do not use sweater, detergents, abrasive cleaning liquids or chemical agents (alcohol, gasoline etc.)
to clean the unit.
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the retailer where the product
was purchased. They can take this product for environmental safe recycling.
WARNING: To avoid overheating, do not cover the heater
Any questions, please contact us through Amazon message or send us an email to services@homeleader.com.
cn. We will reply as soon as we can and solve your concerns. Please do leave us a review about the chopper if
it works fine. Enjoy the product! Thanks.
Table of contents
