Office Star Products SPACE 13-7N20D User manual

2
1
FEATURE
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever (1) up.
To lower seat height sit on chair and lift lever (1) up.
• FOOTRING HEIGHT ADJUSTMENT
To adjust footring height, loosen knob (2) adjust footring to
desired height, and tighten knob (2) completely to secure
footring into position.
13-7N20D
DRAFTING CHAIR
OPERATING INSTRUCTIONS
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and
knobs are securely tightened.
3. Check that all bolts screws and knobs are tight
every three months or as needed.
4. Dispose of packing material properly. Do not use
plastic cover as head covering. It may cause
suffocation.
5. Do not use chair as a stepladder.
6. Use this chair for its intended purpose only.
7. Use mild detergent only for cleaning.
LIMITED WARRANTY
SPACE®chairs are warranted* from the date of purchase against failure due to material and workmanship as follows:
 •Lifetimeoncomponentpartsincludingpneumaticcylinder,controlmechanism,baseandcasters.
 •3Yearsonupholsteryfabricandfoamagainstwearanddeterioration.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons
weighing 250 lbs. or less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism,
rusting, acts of nature or any other event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may
result from normal use. Liability for incidental or consequential damages is excluded. The user assumes all risk of injury resulting from use of
this product. When usage is more than 40 hours per week, a five year warranty on all parts applies. Fabric is warranted for one year. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state.
To make a warranty claim, contact Parts Department via e-mail parts@officestar.net, by Fax [phone], or toll free parts
number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacic Time. Provide model number and description of the
problem and obtain conrmation number. At it’s option Ofce Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer’s component.
It is the customer’s responsibility to prepay freight on any components returned to the factory. Return freight on components
covered by warranty will be paid by Ofce Star Products.

PART QTY
1. Base ....................1
2. Casters ..................5
3. Pneumatic Cylinder .........1
4. Footring ..................1
5. Seat Cushion ..............1
6. Back Assembly . . . . . . . . . . . . 1
7. Allen Screws . . . . . . . . . . . . . . 4
8. Back Support (Pre-Installed) . . 1
9. Allen Wrench ..............1
1
Remove all parts from carton, separate by part numbers indicated on parts list, and verify part quantities.
STEP 1 Insert five Casters (2) into Base (1), push hard until you feel or hear the Caster (2) snap into place.
STEP 2 SlidePneumaticCylinder(3)throughFootring(4)andintoBase(1).
STEP 3 Attach Back Support (8) to rear of Seat Cushion (5) using four Allen Screws (7),
FULLY TIGHTEN ALL SCREWS USING ALLEN WRENCH (9).
STEP 4 PlacetheassembledseatontopofPneumaticCylinder(3)andapplydownwardpressure.
ATTENTION: MAKE SURE ALL SCREWS ARE FULLY TIGHTENED BEFORE USING CHAIR.
13-7N20D
DRAFTING CHAIR
ASSEMBLY INSTRUCTIONS
© Office Star Products July 2008
STEP 1 STEP 2
STEP 4
2
3
4
X5
3
1
STEP 3
9
7
8
X4
5
6
6