Office Zone ECO-S Punch & Binding Machine 2:1 Pitch User manual

1
1-800-543-5454
[phone]
Model ECO-S Punch and Binding Machine
2:1 Pitch
Set up
Choose stable surface
Place machine on a stable
surface.
Shelves are not recommended.
Placerequirement.
Keep working space free:
Right 8” (20 cm)
Left 6” (15 cm)
Have binding elements near
workarea.
Store binding elements in the
special boxes.
Size: 24 x 36 cm
9.5”x14.2”
Protect sensitive furniture surface.
The machine stands on soft plastic feet.
Some surfaces may discolor after a
time.
Operation
Before first use:
Punch scrap paper to clean the
rust preventative from the
punch dies.
Field of application:
Punch:
Paper:
Max 30 pages 20 # stock for
comfortable punching:
15-20pages
Cardboard
Maxthickness1.5mm
Plastic Foil
Max 2 pages for 0.3 mm thickness
Max. binding thickness 28 mm (1-1/8”)
Approx. 280 pages 20 # stock.
Maintenance
The machine
and the parts
1
Measure
Determination of the diameter
Put the back on the edge against
the measuring scale.
Read the diameter ofthe binding
element (e.g. 3/8”)
Office Zone
1-800-543-5454

2
Adjust
Scale for adjusting the diameter
Release attachment screw, determine
scale, adjust diameter, tighten
attachment screw
Adjust distance edge to
according diameter turn knob
Turn knob index to the
according diameter (e.g. 3/8”)
bigger 0–bigger edge.
Adjust format 11” Paper guide right
Pullpins
Screw down the right paper guide, pull
5 pins from left (21 loops).
Adjust format 8.5” Paper
guide left
Pullpins
Screw down the left paper
guide, pull 5 pins from left
and 5 pins from the right (16
loops).
3
Insert
Lay binding element in front of the
clamping fixture
Small loops on top, facing rear.
Press down clamping fixture
Press back edge and front side
will open.
Push binding element under the
clamping fixture.
Clamping fixture holds binding element
during insertion of the punched paper.
Release clamping fixture
possibly adjust binding
element vertically.
4
Prepare
The seam of the closed binding
element should be inside the book
Not outside the covers
Set the book upright, binding
side to the top, place the back
cover in front
The front cover should be
behind the back cover.
Jog the book Turn the book over, covers are
underneath
Take pages from the top
5
Punch
Punch max 30 pages 20# stock,
for comfortable punching: 15–
20 pages
Punch plastics and thicker covers
separately.
Insert paper into punching slot,
slide the paper against the paper
guide
Adjust 11” format at the right
side, paper must stand evenly, if
not align it again
Adjust 8.5” format at the left
side.
Press punching level forward
until it stops, then return to
originalposition.
Hold the machine with the other
hand.
6
Insert
Remove punched paper from the
punching slot. Insert paper onto the binding element
For thicker books, repeat steps five and six until all pages are
punched.

3
7
Adjust
Press clamping fixture After the paper had been placed
on the binding element, remove
the paper with the element from
the clamping fixture.
Hold the paper that it does not
slide out of the binding element.
Put binding element under the
closing bar. Binding element must stand vertically at the back of the
closing bar
With opening of the binding
element to the book.
8
Close
Press binding lever forward until
it stops and back again
For bigger diameters use more
force.
Proper bind Binding under closed:
Adjust closing bar a little deeper
Release attachment screw and
move it slightly to the left. Fix
attachment screw. Press binding
lever again.
Bindingoverclosed:
Adjust closing bar a litter higher
Release attachment screw and
move it slightly to the right. Fix
attachment screw. Close next
book.
9
Ready
Turn back cover over Ready

4

5