Officient OMEGA 24/7 STOOL User manual

PARTS INSTRUCTIONS
PART DESCRIPTION QTY
1Casters 5
25-Star Base 1
3Cylinder 1
4Foot Rest 1
5Knob 1
6Seat Plate 1
7A Left Arm 1
7B Right Arm 1
8Seat Cushion 1
91
10 1½" EZ Knobs 2
11 1" EZ Knobs 2
13 Plastic Caps 8
14 Hexagonal Wrench 1
INSTRUCTIONS
A. Remove all parts from the carton and separate them into part number groups as indicated in the parts list.
B. T
Turn the base (2) (3) into the center hole on the base (2).
o begin assembly, place the 5-star base (2) upside down and insert casters (1) into the bottom of base (2).
C.
D.
E.
Attach the seat plate (6) to the bottom of the seat cushion (8) (with front of seat plate facing the front of the
seat cushion) by using 1½" EZ knobs (10) into the front holes of the seat plate (6) and 1" EZ knobs (11)
into the rear holes of the seat plate (6) as shown in diagram 3. Tighten the knobs..
F.
Place the assembled chair on top of the cylinder (3) and press down until fully engaged.
Place the plastic caps (13) into the two arm holes on each arm.
Periodically (every 90 days) make sure that the screws are still fully tightened.
G.
I.
ASSEMBLY INSTRUCTIONS
12 1¼" Small Screws 8
H.
J.
Back Cushion
Select a smooth surface in order not to scratch the parts. Align the arm holes with the holes on the
cushions (8 & 9) by using 1¼" small screws (12) through the arm holes to the cushions (8 & 9). This will
secure the arm to the cushions as shown in diagram 1. Do not tighten the screws completely!
Turn the chair over to the other side and assemble the second arm as shown in diagram 2. Now tighten
all the screws on arms.
Turn the knob (5) counterclockwise to loose the foot rest (4), then insert the foot rest (4) to the cylinder (3).
Tighten the knob.
WWW.OFFICIENTFURNITURE.COM
OMEGA 24/7 STOOL
ATTENTION:
Make certain to fully tighten all screws
before using chair.
WE SUGGEST TAPING THE WRENCH UNDER
THE SEAT FOR FUTURE USE.

OPERATING FEATURES 1. TO ADJUST SEAT HEIGHT:
While seated, lean forward and reach under the right side
of the chair to locate the handle. Lift the handle and raise
your body up slightly to allow the chair to rise to the desired
height. To lower the seat, lift the handle while applying more
weight downward on the seat. The chair will descend until the
handle is released or the chair reaches the lowest position.
2. TO ADJUST POSITION OF FOOT RING:
Turn knob to loosen, slide foot ring up or down along height
of cylinder. Then tighten knob.
WARNINGS
1. This product should be used by only one person at a time.
2. Do not use this chair unless all bolts, screws and knobs are
securely tightened.
3. Save the hexagonal wrench. Check that all bolts, screws and
knobs are tight every three months or as needed.
4. Dispose of packing material properly. Do not use the plastic
cover as a head covering. It may cause suffocation.
5. Do not use the chair as a stepladder.
6. Use this chair for its intended purpose only.
7. The casters sold with this chair are intended for use on
carpet. They are not recommended for use on tile or hard-
ASSEMBLY INSTRUCTIONS
3. TO ADJUST ARMS:
This chair has an adjustable arm function so the arms can
be pushed up or pulled down. The arms can be pushed up
next to the back cushion so the chair can easily roll under
a desk.
OMEGA 24/7 STOOL
WWW.OFFICIENTFURNITURE.COM