Ofna Racing Ultra LXComp User manual

INSTRUCTION MANUAL
Ultra LX Comp2 Rev:01
• New Arms Design
• New Bumper
• Uses Less ”E” Clips
• 12mm X-1 Racer Shocks

REQUIRED FOR OPERATION
THINGS NEEDED
AA Batteries ( 12 pcs )
Glow Fuel
20%
TOOLS NOT INCLUDED IN KIT,
BUT NEEDED TO MAINTAIN YOUR CAR.
Phillips Type Screw Drivers ( L )
Phillips Type Screw Drivers ( S )
Needle Nose Pliers
Cutter
91009
Curved Scissors
$5.95
Knife
10239
Instant Cement
Cross Wrench
#17109 $3.95
#10796 $3.95
Glow Plug & 17MM Cross Wrench
#10801 $6.95
10620
Diff Gear
Grease
$9.95
You need to get batteries for the radio transmitter and the car receiver
packs.
• Radio TX needs (8) eight AA batteries.
• Car needs (4) four AA Ni-cad batteries, Alkaline type batteries will
work, but braking will be reduced. The best is to use a 5 cell hump
pack for increased voltage..
Recommended Option:
You may want to upgrade the car battery pack to a Ni-Cad or NiHm 5
cell type(600AE). This will give more run time. OFNA #10212
You will need to buy a few items to start the engine and run the car.
• Use 20% nitro CAR fuel. Do not use airplane or heli fuels, they will
over heat engine.
• Buy LONG glow plugs, like OFNA/PICCO Plug (#51007-cool or
51008-med). Use plugs without idle bar. Do NOT use plugs, like the
MC-59 or OS-8 or any short plug
In your box you will find..
• #10162 - Bottle, 250cc
• #10219 - Red “D” size glow heater
#10212 NiHm Hump Pack,
see charger 10214.
10214
Over-nite
Charger

MUST READ THIS BEFORE RUNNING
Running a nitro kit is fun and easy, but to make this a safe rusting.
• Clean oil and dirt from chassis with a degreaser.
and good experience you must observe a few rules. This
kit is extremely fast, easily over 40MPH, and can seriously Precautions
injure someone if you are not careful. • This kit is not a toy. Always run car with a second
person as a spotter and pitman.
Where to run car?
• Any running area you choose must be dry. Do not run • Hot Parts - The pipe, manifold, engine and head are very
car near any water or wet dirt. hot and will cause burns.
• Do not run on public streets. It is very easy to have the
car run over or damaged by hitting the curb. • Rotating Parts - Keep hands away from the drive train,
• Do not operate car in tight confined places. The car is wheels, and engine when engine is running.
very fast and will easily hit something.
• Do not run near people or animals. • Radio - Check batteries life before running the car. If
radio does not have full control of the car with steering
• Due noise, you will want to consider the surrounding and/or throttle/brake do not run until corrected. Failure to
area when operating the car. correct this will result in possible injury and damage to the
• Do not operate the car at night. You will not be able to car or property.
drive it without hitting something.
• Do not operate the car indoors. Engine exhaust is not • Glow fuel - Do leave the glow fuel unattended with the lid
healthy. off. Fuel contains Methanol and Nitro Methane and is
flammable and poisonous.
Glow Fuel
• Glow fuel is poisonous! Store fuel in cool ventilated location. Refer the glow fuel
• Glow fuel is flammable!
• Do not leave in fuel bottle with lid off at any time. label for additional precautions.
• Do not use any fuel other than glow fuel in this engine.
• Car Fuel tank - Never store fuel in car tank, it will ruin the
First Time Starting the Engine engine if left in tank.
Caution! When starting engine make sure the following is
observed. • Always turn off the car BEFORE turning off radio.
• Set engine Master needle to 3 turns (rich setting)
• Do not do this alone, get an experienced friend to help at • DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY
first. ISSUE.
• Fill fuel tank, try not to spill fuel. Do not spill fuel on
receiver IF YOU DO NOT BREAK-IN ENGINE
• Hold car off the ground, so it will not runaway when first CORRECTLY, MAINLY AT LOW RPM,
starts
• Turn on Radio and check the linkage before starting YOU WILL BREAK THE CONNECTING
engine. ROD!
• Turn on car receiver battery switch.
• Always have an air filter on the carburetor to keep dirt
out. FAILURE TO NOT READ AND
Engine Break-in FOLLOW BREAK-IN ENGINE
• See Engine Page.
Emergency Stopping Engine When Running INSTRUCTIONS WILL VOID
• Remove air filter and cover carb. intake.
• Squeeze fuel line and hold until engine stops. WARRANTY!
• With a rag, cover exhaust outlet.
Storing Car After Running CHECK RADIO SETTING AND
• Remove fuel from tank and fuel lines
• Turn off radio in car LINKAGE BEFORE STARTING
• Put a few drops of after run in engine to keep it from
The car is very fast
and will too easily hit someone.

CHECKING ENGINE THROTTLE
* Insert into transmitter.
1. Insert AA batteries into
transmitter (8 Pcs).
2.Turn on transmitter.
3.Turn on receiver.
4.Center throttle trims as
shown .
ABC
1. Pull Full Throttle. 1. Push trigger to full
brake position.
2. Adjust alum. Stopper to
increase or decrease
the brake.
Idle Position (A)
Brake (C)
Full Throttle (B)
* Align throttle servo same
as shown.
ASSEMBLY OF THE THROTTLE LINKAGE SYSTEM
3X3mm
Set Screw
3X3mm
Set Screw
3X3mm
Set Screw
Plastic Collar
* Take the plastic collar
from brake system plastic
parts.
Throttle
Spring
#10300
Alum.Stopper
#10300
Alum.Stopper
* Snap On.
#30530
Plastic Throttle
Ball Joint
2mm Rod
Fuel
Tube
( 6mm )
Idle Position
Brake
Full Throttle
* Align throttle servo same
as shown.
A
B
C
• Full brake arm position.
Spring compresses
forward and brake rods
pull brake levers.
• Full throttle arm position.
Spring rod pulls throttle
barrel open and brake
rods release pressure on
brake cams.
IMPORTANT
CHECK RADIO
THROTTLE AND
STEERING SWITCHES
BEFORE RUNNING CAR
#30800
Plastic Throttle
kit
Note:
Battery life is short when using Alkaline batteries. For safety, we recommend using
Alkaline batteries for only 30 minutes before testing; mostly changing. Battery strength
affects braking power and radio range. If voltage drops while running the car, you will
loose control and destroy your car! This is NOT covered under warranty.
To increase run time, upgrade receiver battery to a 5-cell hump pack. Also, install a
battery fail safe (OFNA # 91002) to further protect your car. But, the most important step
you can make, “is to always use fully charged or fresh batteries when running your car”.
Radio shown, may be
different from what is in
your kit. OFNA
reserves the right to
change upon stock
availability.
A
B
C
Your Radio may be different
than one pictured in this
manual.

* Put the differential gears
same as picture shown.
30901
Cap Joint
30620
x19x6mm
Ball bearings
30751(Fro nt/Rear)
30761(Center)
Diff. Case
30779
P5
O-Ring
30779
2x12.8
30779
2x12.8
30779
P5
O-Ring
30751(Front/Rear)
30761(Center)
Diff. Case
94034
Set Screw
30779
0.5x26mm
O-Ring
*Apply diff. Gear grease
to the differential, during
assembly.
*Fill the dif. Case to
approx 80% with grease
30901
Cap Joint
30769
Diff. Gear
(Large)
30769
Diff. Gear
(Large)
30779
4x10mm
Washer
30779
4x10mm
Washer
30779
4x10mm
Washer
30779
4x10mm
Washer
30773
4mm
Cross Pin
30773
4mm
Cross Pin
30769
Diff. Gear
(Small)
30769
Diff. Gear
(Small)
30769
Diff. Gear
(Small)
30769
Diff. Gear
(Small)
30773
4x27mm
Cross Pin X2
30779
2x12.8mm X2
30779
4x10mm Washer X4
30779
P5 O-Ring X2
94034
Set Screw X2
*Notice the straight
holes are for the
front and rear only.
ASSEMBLY OF THE FRONT AND REAR DIFFERENTIAL
*Builds two differentials for
font and rear.
94004
3X12mm
Hex Screw
94004
3X12mm
Hex Screw X4
Step 1
Step 2
ASSEMBLY OF THE DIFFERENTIAL GEAR
30620
7x19x6mm
Ball bearings

30911
Break Cap Joint
30620
7x19x6mm
Ball bearings
30620
7x19x6mm
Ball bearings
30761(center)
30751(F/R)
Diff. Case
30779
2x12.8
30769
Diff. Gear
(Large)
30779
2x12.8
30779
P5
O-Ring
30761(Center)
30751(F/R)
Diff. Case
94034
Set Screw
30779
0.5x26mm
O-Ring
*Notice the tapered
holes are for the
center differential only.
30769
Diff. Gear
(Large)
30911
Break Cap Joint
30779
P5
O-Ring
ASSEMBLY OF THE CENTER DIFFERENTIAL
30773
4x27mm
Cross Pin X2
30779
2x12.8mm X2
30779
4x10mm Washer
X4
30779
P5 O-Ring X2
94034
Set Screw X1
* Put the differential gears
same as picture shown.
*Apply diff. Gear grease
to the differential, during
assembly.
*Fill the dif. Case to
approx 80% with grease
30779
4x10mm
Washer
30779
4x10mm
Washer
30779
4x10mm
Washer
30779
4x10mm
Washer
30773
4mm
Cross Pin
30773
4mm
Cross Pin
30769
Diff. Gear
(Small)
30769
Diff. Gear
(Small)
30769
Diff. Gear
(Small)
30769
Diff. Gear
(Small)
94004
3X12mm
Hex Screw
94004
3X12mm
Hex Screw
X4
ASSEMBLY OF THE DIFFERENTIAL GEAR
Step 1
Step 2

*Notice the tapered
holes are for the
center diff. Only.
35313
Nylon Nut
31040
51T Spur Gear
30111
3x10mm
Flat Head
Hex Screw
30201
Center Diff. Mount
(Front)
30201
Center Diff. Mount
(Rear)
35313
M3 Nylon Nut
X4
X4
X4
30111
3x10mm
Flat Head Hex Screw
Center differential
assembly
ASSEMBLY OF THE SPUR GEAR
94033
M3x3
Set Screw
30171
Brake Lever
30213
Brake Cam
ASSEMBLY OF THE BRAKE CAM
94033
M3x3 Set Screw
* The picture show are
center differential after
assembly.
Note
the holes for the rear
diff. Mount are width
* Note:
the holes for the rear
diff. Mount are closer .together

94005
3X15mm
Hex Screw
94005
3X15mm
Screw
36660
Brake Pad
36661
Brake Pad
Linings
36650
Brake Disk
Steel
36650
Brake Disk
Steel
0.5mm *Leave a 0.5mm space
between brake disk and
brake pad.
30211
Plastic Bushing
30212
Ball Bearing
30213
Brake Cam
30652
Center Diff.
Plate
94004
3X12mm
Hex Screw
30211
5x8x2.5mm
Plastic Bushing
94033
M3x3 Set Screw
X2
X2
94005
3X15mm Hex Screw
X4
94004
3X12mm Hex Screw
X4
94033
M3x3
Set Screw
30171
Brake Lever
* Remove the double-side tape
before assembly.
ASSEMBLY OF THE BRAKE CAM AND BRAKE PADS
*Leave 3mm gap
between the brake cam
and nut.
3mm
Note:
ASSEMBLY OF THE BRAKE CAM AND CENTER PLATE
ASSEMBLY OF THE BRAKE PADS
30211
Plastic Bushing
30212
Ball Bearing

30121
3x4x4mm
Chromed Tube
30121
3x5mm
Hex Screw
30120
Bevel Gear
(Large / Metal)
*Push 3mm tubes into the
holes of the diff. Case.
36730
Cap Joint
94036
5x5mm
Set screw
30630
6x13x5mm
Ball Bearing
30010
Gear Box
30630
6x13x5mm
Ball Bearing
30130
Bevel Gear
(Small)
34021
Front Upper Arm
Holder
94010
4x12mm
Hex Screw
X430121
3x5mm Hex Screw
30121
4x3x3mm
Chromed Tube
X4
94036
M5x5 Set Screw X1
X2
94010
4x12mmHex Screw
ASSEMBLY OF THE FRONT BEVEL GEARS
ASSEMBLY OF THE FRONT GEAR BOX
94029
4x25mm
Flat Head Hex Screw
94009
4x10mm
Hex Screw
94022
3x18mm
Flat Head Hex Screw
94022
3x18mm
Flat Head
Hex Screw
94009
4x10mm
Hex Screw
X2
X2
94029
4x25mm
TP Flat Head
Hex Screw X2
Step 2
Step 3
Step 4
Step 1
94003
3X10mm
Hex Screw
X1
94011
4X15mm
Hex Screw
94011
4X15mm
Hex Screw
X2
X2
90018
3X25mm
Cap Screw 90018
3X25mm
Cap Screw
30160
Front Lower
Arm Holder
94003
3X10mm
Hex Screw
30102
Front body
Post
36610
Shock Support
Steel
34018
Shock Tower
* Notice the direction.
* Builds two differential for
front and rear.
30010
Gear Box
Front Cover
* Place 5x5mm
set screw in d cut.
36507
Shock Support
Alum

X2
X2
90026
5x5mm Set Screw
36055
2.5x16.8mm Pin
ASSEMBLY OF THE FRONT UPPER ARMS
ASSEMBLY OF THE KNUCKLE ARMS
ASSEMBLY OF THE FRONT LOWER ARMS
40104
10mm
Ball and Socket
36860
5x35mm
36860
5x35mm
40104
10mm
Ball and Socket
34034
Front Upper
Arm Ball End
34034
Front Upper
Arm (Right)
34034
Front Upper
Arm (Left)
34034
Front Upper
Arm Ball End
40104
10mm
Steering Ball
40104
10mm
Steering Ball
40103
Knuckle Arm
(Right)
40103
Knuckle Arm
(Left)
34035
Front Lower
Arm
34036
Front Lower
Arm
36055
2.5x16.8mm
Pin
36055
2.5x16.8mm
Pin
36054
Wheel Hub
36054
Wheel Hub
36053
8x16x5mm
Ball bearings
36053
8x16x5mm
Ball bearings
36053
8x16x5mm
Ball bearings
36152
Universal Joint
36152
Universal Joint
36870
4x10mm
Set Screw
90026
5x5mm
Set Screw
90026
5x5mm
Set Screw
36870
4x10mm
Set Screw
* Leave 8mm
*"L" mark for left side.
* Builds two upper arms for use.
* A4x10mm set screw is used
to adjust the ride heigh.
11

X2
30151
4mm Arm Shaft
30152
3mm Arm Shaft
X4
X2
Assembly of the right and left hand side
are the same.
ASSEMBLY OF THE FRONT ARMS
40104
4x16mm
Cap Screwl
90020
2.5mm
E-Ring
90020
2.5mm
E-Ring
30152
3mm Upper
Arm Shaft
40104
4x16mm
Cap Screwl
3mm
E-Ring
90021
3mm
E-Ring
30151
4mm
Arm Shaft
90021
3mm E-Ring
90020
2.5mm E-Ring
X4
40104
4x16mm Cap Screw X4
34035
Front Lower
Arm
Screw
Cment
e
Screw
Cement

94002
3x8mm
Screw
X2
X2
3x8x0.8mm
Washer
94002
3x8mm button Screw
3x8x0.8mm
Washer
30341
Stabilizer Ball
30403
6mm Ball
40029
Stabilizer
Ball End
40029
Stabilizer
Ball End
34035
M3x8mm
Set Screw
94006
3x18mm Screw
34035
M3x8mm Set Screw
X2
X2
A
B
94033
M3x3 Set Screw X2
94033
M3x3
Set Screw
* Cut the plastic as shown.
34037
Caster Adjuster
CLIP IN THE CASTER ADJUSTER Assembly of the right and left hand side
are the same.
ASSEMBLY OF THE FRONT STABILIZER
34027
Stabilizer
* o change the caster angle .use adjuster t
*Caster angle will
become bigger.
*Caster angle will
become less.
Caster
Adjuster
94006
3x18mm
Screw
Assembly of the right and left hand side
are the same.

94022
3x18mm
Flat Head Hex Screw X2
94022
3x18mm
Flat Head
Hex Screw
94029
4x25mm
Flat Head Hex Screw X2
94029
4x25mm
Flat Head
Hex Screw
X2
X2
X1
94027
4x16mm
Flat Head Hex Screw
94027
4x16mm
Flat Head Hex
Screw
94019
3x10mm
Flat Head Hex Screw
94019
3x10mm
Flat Head
HexScrew
Set triangle marks in
the direction shown
in Fig.(1)
36730
Cap Joint
90026
5x5mm
Set screw
X1
90026
5x5mm
Set screw
30630
6x13x5mm
Ball Bearing
30010
Gear Box
30630
6x13x5mm
Ball Bearing
30130
Bevel Gear
(Small)
Step 2
Step 1
90018
3X25mm
Cap Screw
90018
3x25mm
Cap Screw
30010
Gear Box
Front Cover
36610
Shock Support
Steel
30351
Toe-in Cams
30351
Rear Lower
Arm Holder
ASSEMBLY OF THE REAR GEAR BOX
ASSEMBLY OF THE REAR SHOCK TOWER
34033
Rear Body
Post
34019
Shock Tower
1
Degree
1.5
Degree
Fig.1
Use rear tor-in adjustere.
* place 5X4 mm
set screw in D cut

30151
4mm Arm Shaft
36170
3mm
Arm Shaft
40028
Driver Shaft
(93mm)
E«¬¦©
90021
3mm
E-Ring
90021
3mm
E-Ring
34035
Plastic Washer
34035
Plastic Washer
36081
Wheel
Rear Hub
36053
8x16x5mm
Ball Bearings 36053
8x16x5mm
Ball Bearings
90026
5X5mm
Set Screw
X4
X4
X2
X2
X2
X2
X2
90021
3.0mm E-Ring
36850
7mm Ball
36850
7mm Ball
36880
Turnbuckle
35313
M3
Nylon Nut
35313
M3
Nylon Nut
X2
90026
5x5mm
Set screw
94006
3X18mm Screw
94001
3X4mm Screw
94001
3X4mm
Screw
35313
M3 Nylon Nut
40065
Upper arm
Plastic Rod End
40065
Upper arm
Plastic Rod End
36055
2.5x16.8mm
Pin
36082
Rear Wheel
Axle Shaft
18mm
ASSEMBLY OF THE REAR WHEEL HUB ASSEMBLY OF THE REAR UPPER ARM ROD
*Builds two rear wheel hubs for use. * Builds two rear upper rods for left
and right hand-side.
* Anticlockwise mark.
90018
3X25mm Cap Screw
90018
3X25mm
Cap Screw
ASSEMBLY OF THE REAR LOW ARMS INTO GEAR BOX
0 10 20 30 40 50
mm
Assembly of the right and left hand side
are the same.
* Insert the rear drive shaft
before assembly.
36054
Wheel Hub
94006
3X18mm
Screw
36170
3mm Arm Shaft
30151
4mm Arm Shaft
34035
Rear Lower Arm
18 19
20

94022
3x18mm
Flat Head Hex Screw
94023
3x20mm
Flat Head Hex Screw X4
35313
M3 Nylon Nut
X2
X2
30270
Wing Stay
(Left)
30270
Wing Stay
(Right)
10290
3mm Alum.
Washer
10290
3mm Alum. Washer
94022
3x18mm
Flat Head Hex
Screw
94022
3x18mm
Flat Head Hex Screw
94023
3x20mm
Flat Head
Hex Screw
94023
3x20mm
Flat Head Hex Screw
30270
Wing Stay
Post
35313
M3 Nylon Nut
94011
4X16mm
Hex Screw 94011
4X16mm
Hex Screw
90019
3X25mm
Cap Screw
1. (High Position) 2. (Low Position) 3. (Bigger Angle)
* The installing angle becomes bigger in order 1 to 3.
3x8x0.8mm
Washer
94002
3x8mm Screw
94006
3x18mm
Screw
94002
3x8mm
Screw
3x8x0.8mm
Washer
94033
M3x3
Set Screw
30401
Stabilizer
Ball End
30340
Stabilizer Ball
30401
6mm Ball
30401
Stabilizer
Ball End
94035
M3x8mm
Set Screw
ASSEMBLY OF THE REAR STABILIZER ASSEMBLY OF THE STABILIZER ROD
34027
Stabilizer
AB
* Cut the plastic as shown.
90019
3x25mm
Cap Screw
ASSEMBLY OF THE WING STAY
30270
Wing Mount
X2
X6
X2
X2
X2
94006
3x18mm
Screw X2

x2
94006
3x18mm
Hex Screw
94003
M3x10mm
Hex Screw
30540
Front Plate
30380
Servo Saver
Post
34014
Front Stiffener
94005
3X15mm
Hex Screw
35318
M3 Nylon Nut
x2
94006
M3x18mm
Hex Screw
36742
Servo Saver
Bushing
36750
Servo Saver
Connevtor 35313
3mm
Nylon Lock Nut
35313
3mm
Nylon Lock Nut
36743
6mm E-Ring x4
36740
Servo Saver
Top Adapter
36746
6mm
E-Ring
36740
Servo Saver
Horn B
36740
Plastic Tube
36740
Saver Saver
Shaft (Brass)
36743
6mm
E-Ring
36743
6mm
E-Ring
36743
6mm
E-Ring
36740
Saver Saver
Shaft (Brass)
36741
8x12mm
Washer
36741
Servo Saver
Spring
36740
Servo Saver
Hom A
36740
Servo Saver
Hom A
36700
7mm Steering
Ball End
36850
7mm
36850
7mm
36700
7mm Steering
Ball End
40018
4x56mm
Turnbuckle
36.5mm
*Made two steering rods
for left and right hand-side.
0 10 20 30 40 50
mm
ASSEMBLY OF THE SERVO SAVER
ASSEMBLY OF THE STEERING TIE-ROD
40039
3mm
Tapered Washer
94005
M3x16mm
Hex Screw
94005
M3x16mm
Hex Screw
94003
M3x10mm
Hex Screw
36740
Servo Saver"A" and" B"
Plastic Set
94005
3x15mm Hex Screw
94003
3X10mm Hex Screw x5
x2
40039
3mm
Tapered Washer
94021
3x15mm
Flat Head Hex Screw
X2
40039
3mm Tapered Washer
X2
cS rew
Cement
Scr we
Cement

14.14.
36100
Center Drive
Shaft(Front)
94027
4x16mm
Flat Head
Hex Screw
94023
3x25mm
Flat Head Hex Screw x2
*Insert center drive shaft into
cap joint
Center Diff.
Assembly
94026
4x12mm
Flat Head Hex Screw
x2
94027
4x16mm
Flat Head Hex Screw x8
94019
3x10mm
Flat Head Hex Screw
x2
ASSEMBLY OF THE GEAR BOX ONTO CHASSIS
94023
3x25mm
Flat Head Hex Screw
94027
4x16mm
Flat Head Hex Screw
94019
3x10mm
Flat Head Hex Screw
94026
4x12mm
Flat Head Hex Screw
94027
4x16mm
Flat Head Hex Screw
34016
Chassis (Hard-Coated)
34035
Front Bumper
26

36100
Center Drive
Shaft (Rear)
94027
4x16mm
Flat Head
Hex Screw
94023
3x25mm
Flat Head
Hex Screw
94027
4x16mm
Flat Head
Hex Screw
34080
Stone Guard
34080
Stone Guide
94027
4x16mm
Flat Head Hex Screw X4
94023
3x25mm
Flat Head Hex Screw
94019
3x10mm
Flat Head Hex Screw X6
94019
3x10mm
Flat Head
Hex Screw
94019
3x10mm
Flat Head
Hex Screw
94019
3x10mm
Flat Head
Hex Screw
*Insert drive shaft into
cap joint before assembly.
ASSEMBLY OF THE REAR BOX ONTO CHASSIS
ASSEMBLY OF THE STONE GUARD
X2
27
28

94003
3X10mm Hex Screw X12
94003
3X10mm
Hex Screw
34025
Radio Tray
94003
3X10mm
Hex Screw
94003
3X10mm
Hex Screw
94003
3X10mm
Hex Screw
94005
3X16mm
Hex Screw
94005
M3x16mm Hex Screw
X2
Steering Servo
Throttle Servo
94003
3X10mm
Hex Screw
94004
3X12mm
Hex Screw
94004
3X12mm
Hex Screw
94004
3X12mm
Hex Screw
X4
94003
3X10mm
Hex Screw
94003
3X10mm
Hex Screw
94003
3X10mm
Hex Screw
34013
Receiver Box
94003
3X10mm
Hex Screw
94003
3X10mm
Hex Screw
94003
3X10mm
Hex Screw 2X15mm
Hex Screw
2X15mm
Hex Screw
2X15mm
Hex Screw
X2
10280
Switch Cover
Switch
Receiver
Battery
34026
Servo Washer
34026
Servo Washer
34026
Servo Mount
34026
Servo Washer
34012
Radio Tray
Alum, Post
34020
Servo Mount
Put the receiver and
battery into receiver
box.
34013
Receiver Box
Cover
Front Steering
Servo
34015
Sensor
Support
ASSEMBLY OF THE FRONT SERVO AND RADIO TRAY
* Put the servo wire into
receiver box and connect to
receiver.
* Connect battery
case wire to switch.
* Connect the switch
wire to receiver.
*Put the protection rubber
onto your servo.
Note:

34070
Rear Stiffener
38120
Alum.
Fuel Tank Post
X7
94019
3x10mm
Flat Head Hex
Screw
94003
3x10mm
Flat Head Hex
Screw
94003
3x10mm
Flat Head Hex
Screw
94003
3X10mm
Hex Screw X4
94003
3X10mm
Hex Screw
94003
3X10mm
Hex Screw
94019
3x10mm
Flat Head Hex
Screw
94004
3X12mm
Hex Screw
94004
3X12mm
Hex Screw X2
40109
Fuel Tank
40109
Fuel Tank
Pressure
Nipple
Pressure
Nipple
ASSEMBLY OF THE RADIO TRAY ONTO CHASSIS
30286
Plastic
Washer
30