Ofna Racing BLAZER SST User manual

INSTRUCTION MANUAL
Strong Front and Rear chassis braces.
Tuned Polished Dual Chamber racing pipe.
Unique adjustable chassis width of 310mm or 330mm.
High performance .26 engine with Shaft Start Motor handle.
Full race Offset King Pin aluminum steering knuckle.
Three sealed differentials with 6 steel gears.
Racing Stadium and Truck tire sets.
Adjustable Front and Rear roll bars.
Multi disc brakes with adjustable bias.
Hard Coated Threaded body oil fill shocks.
5 Degree hard coated 3mm chassis.
Racing 3 shoe clutch with Aluminum CNC flywheel.
Steel main spur gear and center differential.
Adjustable servo saver.
Front CVA joint and 8mm axles.
140+cc fuel tank with inside stone filter.

RTR KITS - REQUIRED FOR OPERATION
THINGS NEEDED
AA Batteries ( 12 pcs )
Glow Fuel
20%
TOOLS NOT INCLUDED IN KIT,
BUT NEEDED TO MAINTAIN YOUR CAR.
Phillips Type Screw Drivers ( L )
Phillips Type Screw Drivers ( S )
Needle Nose Pliers
Cutter
Curved Scissors
#91009 $5.95
Knife
Instant Cement
Cross Wrench
#17109 $3.95
Glow Plug & 17MM Cross Wrench
#10801 $6.95
Grease
You need to get batteries for the radio transmitter and the car receiver packs.
• Radio TX needs (8) eight AA batteries.
• Car needs (4) four AA Ni-cad batteries 2000Mah OFNA #10196 or (4) Alkaline.,
Alkaline type batteries will work, but braking will be reduced and 30 minute life. The
best for car, is to use a 5 cell hump receiver pack for increased voltage and longer
life..
Recommended Option:
You may want to upgrade the car battery pack to a Ni-Cad or NiHm 5 cell
type(600AE). This will give more run time. OFNA #10212 1200NiMh Hump Pack and
NiHm Battery Charger #10214
You will need to buy a few items to start the engine and run the car.
• Use 20% nitro CAR fuel. Do not use airplane or heli fuels, they will
over heat engine.
• Buy LONG glow plugs, like OFNA/PICCO Plug (#51007 or 51008).
Use plugs without idle bar. Do NOT use plugs, like the MC-59 or OS-8
In your box you will find..
• #10163 - Bottle, spout top
• #10219 - Red “D” size glow heater
#10212 NiHm Hump Pack,
see charger 10214.
10214
Over-nite
Charger

MUST READ THIS BEFORE RUNNING
Running a nitro kit is fun and easy, but to make this a safe • Clean oil and dirt from chassis with a degreaser.
and good experience you must observe a few rules. This Precautions
kit is extremely fast, easily over 40MPH, and can seriously • This kit is not a toy. Always run car with a second
injure someone if you are not careful. person as a spotter and pitman.
Where to run car? • Hot Parts - The pipe, manifold, engine and head are very
• Any running area you choose must be dry. Do not run hot and will cause burns.
car near any water or wet dirt.
• Do not run on public streets. It is very easy to have the • Rotating Parts - Keep hands away from the drive train,
car run over or damaged by hitting the curb. wheels, and engine when engine is running.
• Do not operate car in tight confined places. The car is
very fast and will easily hit something. • Radio - Check batteries life before running the car. If
• Do not run near people or animals. radio does not have full control of the car with steering
and/or throttle/brake do not run until corrected. Failure to
• Due noise, you will want to consider the surrounding correct this will result in possible injury and damage to the
area when operating the car. car or property.
• Do not operate the car at night. You will not be able to
drive it without hitting something. • Glow fuel - Do leave the glow fuel unattended with the lid
• Do not operate the car indoors. Engine exhaust is not off. Fuel contains Methanol and Nitro Methane and is
healthy. flammable and poisonous.
Glow Fuel Store fuel in cool ventilated location. Refer the glow fuel
• Glow fuel is poisonous!
• Glow fuel is flammable! label for additional precautions.
• Do not leave in fuel bottle with lid off at any time.
• Do not use any fuel other than glow fuel in this engine. • Car Fuel tank - Never store fuel in car tank, it will ruin the
engine if left in tank.
First Time Starting the Engine
Caution! When starting engine make sure the following is • Always turn off the car BEFORE turning off radio.
observed.
• Set engine Master needle to 3 turns (rich setting) • DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY
• Do not do this alone, get an experienced friend to help at ISSUE.
first.
• Fill fuel tank, try not to spill fuel. Do not spill fuel on IF YOU DO NOT BREAK-IN ENGINE
receiver CORRECTLY, MAINLY AT LOW RPM,
• Hold car off the ground, so it will not runaway when first
starts YOU WILL BREAK THE CONNECTING
• Turn on Radio and check the linkage before starting ROD!
engine.
• Turn on car receiver battery switch.
• Always have an air filter on the carburetor to keep dirt FAILURE TO NOT READ AND
out.
FOLLOW BREAK-IN ENGINE
Engine Break-in
• See Engine Page. INSTRUCTIONS WILL VOID
Emergency Stopping Engine When Running
• Remove air filter and cover carb. intake. WARRANTY!
• Squeeze fuel line and hold until engine stops.
• With a rag, cover exhaust outlet.
Storing Car After Running
• Remove fuel from tank and fuel lines
• Turn off radio in car
• Put a few drops of after run in engine to keep it from
rusting.
The car is very fast
and will too easily hit someone.

Step 1
Step 1 Step 2
Step 3 Step 4
Step 2
Step 3 Step 4
ASSEMBLE OF THE DIFFERENTIAL FOR FRONT AND REAR
ASSEMBLY OF THE DIFFERENTIAL FOR CENTER
Builds two differentials for front and rear.
4x4mm
Set Screw
4x4mm
Set Screw
4x4mm
Set Screw
4x4mm
Set Screw
40006
Cap Joint
40006
Cap Joint
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
36053
8x16mm
Ball bearing
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
..........X2
..........X2
..........X2
..........X2
..........X4
..........X4
..........X4
..........X4
..........X1
..........X1
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
40010
2.5x13.8mm
Pin
40009
P6 O-Ring
40009
P6 O-Ring
40009
P6 O-Ring
40009
P6
O-Ring
O-Ring
O-Ring
40012
6x18mm
Washer
40012
6x18mm
Washer
40012
6x18mm
Washer
40012
6x18mm
Washer
40003
Diff. Case
40003
Diff. Case
40005
Break
Cap Joint
40005
Break
Cap Joint
40004
Diff. Gear
(Large)
40004
Diff0. Gear
(Large)
40004
Diff. Gear
(Large)
40004
Diff. Gear
(Large)
Apply diff. Gear grease to the
differential during assembly.
Fill the diff. case to
approx 70% with grease.
Apply diff. Gear grease to the
differential during assembly.
Fill the diff. case to
approx 70% with grease.
30779
4x10mm
Washer
30779
4x10mm
Washer
30779
4x10mm
Washer
30779
4x10mm
Washer
40004
Diff. Gear
(Small)
40004
Diff. Gear
(Small)
30773
4mm
Cross Pin
49032
Large
Bevel Gear
49016
Spur Gear
40011
Diff. Gasket
40011
Diff. Gasket
3x12mm
Flat Head
Hex Screw
3x12mm
Flat Head
Hex Screw
94020
Flat Head
Hex Screw
3x12mm
Flat Head
Hex Screw
3x12mm
Flat Head
Hex Screw
3x12mm
Flat Head
Hex Screw
OPT :
JS-01
CNC Steel Diff. Gear Set
30779
4x10mm
Washer
30779
4x10mm
Washer
40004
Diff. Gear
(Small)
40004
Diff. Gear
(Small)
30773
4mm
Cross Pin
94034
94034
40009
94034
94020
94020
94020
40009
94020
94020
94034

ASSEMBLY OF THE FRONT GEAR BOX
ASSEMBLY OF THE FRONT ARMS HOLDER
40024
13x16x0.2mm
Shim
40024
13x16x0.2mm
Shim
40024
13x16x0.2mm
Shim
49012
Small
Bevel Gear
Adjust the backlash
with the shims.
40017
Gear Box
40017
Gear Box
4x16mm
Hex Screw
4x16mm
Hex Screw
4x16mm
Hex Screw
4x45mm
Hex Screw
40022
Front Lower Arm
Holder
5x4mm
Set Screw
36730
Cap Joint
40015
Front Lower arm
Holder (Rear/Plastic)
40015
Front Upper arm
Holder (Rear/Plastic)
4x45mm
Hex Screw
4x45mm
Hex Screw
Src
e
w
Cment
e
36053
8X16mm
Ball bearing
36053
8X16mm
Ball bearing
Insert two ball
bearings as
shown.
Step 1 Step 2
Step 3
4x16mm
Flat Head
Hex Screw
4x16mm
Flat Head
Hex Screw
4x16mm
Flat Head
Hex Screw
4x16mm
Flat Head
Hex Screw
5x4mm
Set Screw
4x16mm
Flat Head
Hex Screw
..........X2
..........X1
..........X4
..........X2
..........X2
94011
94011
94011
94014
94014
94027
94027
90026
90026
94027
94014
94027
94027

ASSEMBLY OF THE FRONT SHOCK STAY
40116
Shock Tower
4x12mm
Hex Screw
4x12mm
Hex Screw
4x12mm
Hex Screw
3x12mm
Hex Screw
3x12mm
Hex Screw
..........X2
..........X2
Screw
Cement
S re
cw
eet
Cmn
ASSEMBLY OF THE KNUCKLE ARMS
"R" for right hand side.
"L" for Left hand side. 36053
8x16x5mm
Ball bearing
36053
8x16x5mm
Ball bearing
36053
8x16x5mm
Ball bearing
40103
Alloy Front
Knuckle Arm
(Right)
40103
Alloy Front
Knuckle Arm
(Left)
40105
8mm CVD Joint
(Front)
40105
8mm CVD Joint
(Front)
36053
8x16x5mm
Ball bearing
36054
Alum.
Wheel Hub 8mm
36054
Alum.
Wheel Hub 8mm
36055
2.5x17mm
Pin
36055
2.5x17mm
Pin
36055
2.5x17mm
Pin
5x4mm
Set Screw
5x4mm
Set Screw
5x4mm
Set Screw
..........X2
..........X2
ASSEMBLY OF THE FRONT UPPER ARMS
36860
5x35mm
Turnbuckle
40101
Front Upper
Arm Ball End
40101
Front Upper
Arm (Left)
40101
Front Upper
Arm (Right)
40101
Front Upper
Arm Ball End
40104
10mm
Ball and Socket
40104
10mm
Ball and Socket
36860
5x35mm
Turnbuckle
¡¯Appr ox6mm
5x35mmTurnbuckle¡@ ..........X2
ASSEMBLY OF THE FRONT LOWER ARMS
*A 4x10mm set screw is
used to adjust the ride
height.
*A 4x10mm set screw is
used to adjust the ride
height.
40102
Front Lower Arm-L
40102
Front Lower Arm-R
40104
10mm
Ball and Socket
40104
10mm
Ball and Socket
4x10mm
Set Screw
4x10mm
Set Screw
4x10mm
Set Screw ..........X2
94010
94010
94010
94004
94010
36860
90026
90026
90026
36870
36870
36870

Step 1
Step 3
Step 2 ASSEMBLY OF THE
FRONT LOWER ARMS
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
Insert the rear drive shaft into
cap joint before assembly
the rear lower arm.
ASSEMBLY OF THE FRONT SUSPENSION ARMS
40023
Lower Arm
Shaft (4mm)
90021
E-Ring
3mm
E-Ring
90021
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
36170
Arm Shaft
3mm
..........X4
..........X4
..........X4
ASSEMBLY OF THE
FRONT LOWER ARMS
4x16mm
Cap Screw
4x16mm
Cap Screw
4x16mm
Cap Screw
ASSEMBLY OF THE
FRONT KNUCKLE ARMS
CLIP IN THE CASTER ADJUSTER
A
40101
Caster Adjuster
B
A
B
Caster angle will
become bigger.
Caster angle will
become less.
Caster Adjuster
* Use caster adjuster to change the
caster angle.
90020
40104
90020
40104
40104
90021
90020

ASSEMBLY OF THE FRONT STABILIZER
ASSEMBLY OF THE FRONT GEAR BOX ONTO CHASSIS
Step 1
Step 2
3x8mm
Set Screw
40029
Stabilizer
Ball End
30401
6mm
Ball End
40019
Stabilizer
30341
Stabilizer Ball
40199
Stabilizer
Ball End
40290
Stabilizer
Mount Plastic
3x10mm
Hex Screw
3x16mm
Hex Screw
..........X4
..........X2
..........X2
..........X2
3x10mm
Hex Screw
3x16mm
Hex Screw
M3x8mm
Set Screw
M3x3
Set Screw
M3x3
Set Screw
4x16mm
Flat Head
Hex Screw
40064
Chassis
4x16mm
Flat Head
Hex Screw ..........X2
Assembly of the right and left hand side are the same.
94005
40290
94035
94033
94005
40290
94033
94035
94027
94027

40024
13x16x0.2mm
Shim
40024
13x16x0.2mm
Shim
40024
13x16x0.2mm
Shim
49012
Small
Bevel Gear
Adjust the backlash
with the shims.
40017
Gear Box
40017
Gear Box
4x15mm
Hex Screw
4x15mm
Hex Screw
4x15mm
Hex Screw
36053
8X16mm
Ball bearing
36053
8X16mm
Ball bearing
Insert two ball
bearings as
shown.
..........X2
..........X2
Step 1 Step 2
Step 3
40025
Rear
Lower Arm Holder
40027
Win Stay
Mount
40015
Rear arm Holder
ASSEMBLY OF THE REAR GEAR BOX
ASSEMBLY OF THE REAR ARM HOLDER
5x4mm
Set Screw
36730
Cap Joint
5x4mm
Set Screw
4x45mm
Flat Head
Hex Screw
4x45mm
Flat Head
Hex Screw
..........X1
..........X2
4x15mm
Hex Screw
4x15mm
Hex Screw
..........X2
4x10mm
Hex Screw
4x10mm
Hex Screw
..........X2
94011
94011
94011
90026
94011
94009
94030
90026
94009
94011
94030

36081
Wheel
Rear Hub
36053
8x16x5mm
Ball Bearings
36054
Alum.
Wheel Hub 8mm
36053
8x16x5mm
Ball Bearings
5X4mm
Set Screw
Do not tighten
set screw over tighten.
36850
7mm Ball
36850
7mm Ball
36860
5x60mm
Turnbuckle
5x4mm
Set screw
40065
Upper arm
Plastic Rod End
40065
Upper arm
Plastic Rod End
36055
2.5x16.8mm
Pin
36082
Rear Wheel
Axle Shaft
26mm
ASSEMBLY OF THE REAR WHEEL HUB
ASSEMBLY OF THE UPPER ARM ROD
*Builds two rear wheel hubs for use.
* Builds two upper arms for left and right hand-side.
* Anticlockwise mark.
0 10 20 30 40 50
mm
ASSEMBLY OF THE REAR SHOCK STAY
4x12mm
Hex Screw
4x12mm
Hex Screw
40116
Shock Tower
3x12mm
Hex Screw
3x12mm
Hex Screw
..........X2
..........X2
..........X2
ASSEMBLY OF THE FRONT LOWER ARMS
* A 4x10mm set screw is
used to adjust the ride
height.
4x10mm
Set Screw 4x10mm
Set Screw
40102
Rear Lower Arm
40102
Rear Lower Arm
4x10mm
Set Screw ..........X2
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
94010
94004
94010
94004
90026
90026
36870
36870
36870

Step 1
Step 2
Step 3
..........X2
..........X2
..........X2
..........X2
40023
4mm
Lower Arm Shaft
40107
Rear
Driver Shaft
(104mm)
3.0mm
E-Ring
3.0mm
E-Ring
2.5mm
E-Ring
2.5mm
E-Ring
3mm
Plastic Washer
3mm
Plastic Washer
36170
3mm Arm Shaft
M3x3
Set Screw
3X16mm
Cap Screw 3X16mm
Cap Screw
M3
Nylon Nut
35313
Nylon Nut
35313
Nylon Nut
3X25mm
Cap Screw
3X25mm
Cap Screw
*Insert the rear drive shaft
before assembly.
ASSEMBLY OF THE REAR SUSPENSION ARMS
3mm
E-Ring
2.5mm
E-Ring
..........X4
..........X2
Assembly of the right and left hand side are the same.
90021
90021
90020
90020
40102
40102
94007
90018
90021
90020
35313
94007
90018

Step 1
Step 2
ASSEMBLY OF THE REAR STABILIZER
3x8mm
Set Screw
40029
Stabilizer
Ball End
30401
6mm
Ball End
30341
Stabilizer Ball
40199
Stabilizer
Ball End
..........X4
..........X2
..........X2
..........X2
3x10mm
Hex Screw
3x16mm
Hex Screw
3x16mm
Hex Screw
M3x8mm
Set Screw
M3x3
Set Screw
ASSEMBLY OF THE REAR GEAR
BOX ONTO CHASSIS
40019
Stabilizer
3x10mm
Hex Screw
40290
Stabilizer
Mount Plastic
3x10mm
Hex Screw
M3x3
Set Screw
4x16mm
Flat Head
Hex Screw
4x16mm
Flat Head
Hex Screw
4x16mm
Flat Head
Hex Screw
..........X4
40064
Chassis
Assembly of the right and left hand side are the same.
40290
94005
94035
94035
94005
40290
40290
94027
94027
94027
94033
94033

Step 1
Step 1 Step 2
Step 2
..........X1
ASSEMBLY OF THE SERVO SAVER
40095
Servo Saver
Connecting Plate
40031
Plastic
Bushing
40031
Plastic
Bushing
40031
Servo Saver
Horn C
40031
4x8mm
Plastic flange
Bushing
40031
4x8mm
Plastic flange
Bushing
40037
Steering Plat
Hex Screw
40037
Steering Plat
Hex Screw
40036
Servo Saver
Post
M3 Nut
Take the 4x8mm Plastic Flange
bushing and Plastic Bushing
from servo saver plastic
parts tree.
ASSEMBLY OF THE STEERING TIE-ROD
4x10mm
Hex Screw
4x10mm
Hex Screw
4x10mm
Hex Screw
4x10mm
Hex Screw
..........X2
..........X2
* Put the 3mm nut
before assembly.
40031
Servo Saver
Horn A
40035
Servo Saver
Alum. Tube
40031
Servo Saver
Horn B
40033
Servo Saver
Spring
40034
Servo Saver
Spring Tension
Adjuster
M3 Nut
40030
Front Plate
36700
7mm Steering
Ball End
36850
7mm
36850
7mm
36700
7mm Steering
Ball End
40108
4x56mm
Turnbuckle
36.5mm
Builds two steering rods
for left and right hand-side.
0 10 20 30 40 50
mm
3x15mm
Flat Head
Hex Screw
3x15mm
Flat Head
Hex Screw
3x15mm
Flat Head
Hex Screw
3x15mm
Flat Head
Hex Screw
4x10mm
Flat Head
Hex Screw
4x10mm
Flat Head
Hex Screw
..........X4
..........X4
40039
3mm Tapper
Washer(Alum.)
40039
3mm Tapper
Washer(Alum.)
40039
3mm Tapper
Washer(Alum.)
A-A
A-A
..........X2
M3 Nylon Nut
M3 Nylon Nut
94009
35313
35313
94009
94021
94009
94021
94026
35313
94021
35313
94009
94021
94026

Step 1
Step 3
Step 2
Step 4
..........X4
ASSEMBLY OF THE BRAKE AND CENTER DIFF. MOUNT
ASSEMBLY OF THE CENTER DIFF. INTO BRAKE DISK
36660
Brake Pad
40044
Brake Pad
Spring
40044
Brake Pad
Spring
40045
Brake Pad
Adjustment Screw
40045
M3x20L
Brake Pad Adjustment Screw
40043
Center Diff.
Mount Post
40043
Center Diff.
Mount Post
40040
Brake Disc
Holder
40040
Brake Disc
Holder
40040
Center Diff.
Mount
40040
Center Diff.
Mount
40040
Center Diff.
Mount
Assembly the brake disc
holder in the direction
shown.
*Towards the front.
*Towards the Rear.
36661
Brake Pad
Linings
G-06A
Brake Pad
Linings
Remove the double-side
tape before assembly.
A
A
B
C
BC
40044
Brake Pad
Spring
40044
Brake Pad
Spring
40045
Brake Pad
Adjustment Screw
40040
Center Diff.
Mount
A
B
C
40042
Brake Disk
40042
Brake Disk
Center Diff.
Assembly

Step 1 Step 2
Step 4 Step 5
Step 3
ASSEMBLY OF THE CENTER DIFF. INTO CENTER DIFF. MOUNT
3x3mm
Set Screw
40031
Fuel
Proov Plate
30213
Brake Cam
30213
Brake Cam
Plastic
Bushing
Plastic
Bushing
40096
Center Diff.
Plate
30171
Brake Lever
30171
Brake Lever
3x10mm
Hex Screw
3x10mm
Hex Screw
3x10mm
Hex Screw
..........X4
3x3mm
Set Screw
3x3mm
Set Screw
..........X2
40028
Center Drive
Shaft (93mm)
40028
Center Drive
Shaft (93mm)
2.6x10mm
Tapping Screw
2.6x10mm
Tapping Screw
2.6x10mm
Tapping Screw
Insert drive shaft into
cap joint.
ASSEMBLY OF THE CENTER DIFF. ONTO CHASSIS
4x12mm
Flat Head
Hex Screw
4x12mm
Flat Head
Hex Screw
4x12mm
Flat Head
Hex Screw ..........X4
..........X4
94003
30211
30211
94033
94003
94033
94003
94033
94026
94026
94026

Step 3 Step 4
Step 1 Step 2
3x25mm
Cap Screw
3mm
Nylon Nut
40018
Center Chassis
Brace
( Rear )
40018
Center Chassis
Brace
( Front )
ASSEMBLY OF THE CENTER STIFFENER ONTO CHASSIS
3x12mm
Hex Screw
3x12mm
Hex Screw
..........X1
4x16mm
Flat Head
Hex Screw
4x16mm
Flat Head
Hex Screw
4x16mm
Flat Head
Hex Screw
..........X4
..........X1
3X25mm
Cap Screw
..........X1
M3 Nylon Nut
ASSEMBLY OF THE RECEIVER BOX
Use the screw provided
with your radio.
10280
Switch Cover
Switch 40047
Receiver Box
40047
Receiver Box
Cover
40027
Receiver Box
2x10mm
Tapping Screw
2x25mm
Screw
Receiver
30560
Antenna
Pipe
3x10mm
Hex Screw
3x10mm
Hex Screw
..........X1
..........X1
2x25mm
Screw
2x10mm
Tapping Screw ..........X2
35313
94004
94027
90018
94027
94027
35313
90018
94004
94003
94003

Step 1
Step 3
Step 2
Step 4 Step 5
Step 6
40027
Radio Tray
Post
( Plastic )
40027
Radio Tray
Post
( Plastic )
40027
Radio Tray
Post
( Plastic )
Servo Post
10274
Servo Post
40048
40048
ASSEMBLY OF THE RADIO TRAY
Throttle
Servo
Steering
Servo
*Connect as per radio.
49039
Alum.
Radio Tray
40031
Transponder
Holder
3X12mm
Hex Screw
3X12mm
Hex Screw
Battery Case
Battery Cover
37410
Clips
37410
Clips
30560
Antenna
Pipe
Use the original battery
case or rechargeable
hump pack battery.
3x10mm
Hex Screw
3x10mm
Hex Screw
3x10mm
Hex Screw
3x10mm
Hex Screw
3x10mm
Hex Screw
3x10mm
Hex Screw
3x10mm
Hex Screw
3x10mm
Hex Screw
3x10mm
Hex Screw
3x10mm
Hex Screw
..........X16
..........X2
94003
94003
94003
94003
94003
94003
10274
94004
94003
94003
94003
94003
94004

..........X2
..........X4
..........X8
..........X4
..........X4
3x10mm
Flat Head Hex
Screw
3x10mm
Flat Head Hex
Screw 3x10mm
Flat Head Hex
Screw
3x10mm
Flat Head Hex
Screw
ASSEMBLY OF THE RADIO TRAY ONTO CHASSIS
32237
7mm
R-Ring
32237
2mm
Washer
32237
2mm
Washer
32237
1mm
Washer
#315S
1mm
Washer
32237
3.5mm
O-Ring
32237
3.5mm
O-Ring
32237
3.5mm
O-Ring
40076
Shock body
40059
13.8mm
O-Ring
ASSEMBLY OF THE SHOCKS
Fit the o-ring into
groove before assembly.
* Builds 4 for Shocks.
Be careful not to damage
shock shaft.
Step 1 Step 2
49041
Spring Adjuster
40060
2.5mm
Nylon Nut
2.6x5mm
Washer
2.6x5mm
Washer
32235
Shock Piston
Oil Seal
40056
Shock Plastic
Rod End 40055
Short Shaft
40093
Shock Cap
32033
Pressure Top
UP
Down
Move slowly.
1. Pull down piston and
pour oil into shock
cylinder.
FILLING THE SHOCKS WITH OIL
2.To remove air bubbles
by slowly moving
piston up and down.
3. Pull down piston, attach
pressure top and shock
oil overflow with tissue
paper.
*Fit into the groove.
..........X2
M2.5
Nylon Nut
94019
94019
94019 94019
32237

..........X2
..........X2
..........X2
..........X2
..........X2
..........X2
Step 1
40058
Shock Shaft
Dust Cover
ASSEMBLY THE DUST COVER AND SHOCK SPRING
Step 2
30411
6mm
Ball
Push 6mm ball
joint into ball end.
40089
Shock Spring
(Black)
40063
Spring Holder
Plastic
Bushing
Plastic
Bushing
36610
Shock
Upper Fixing
36610
Shock
Upper Fixing
ASSEMBLY OF THE FRONT SHOCK ABSORBERS
ASSEMBLY OF THE REAR SHOCK ABSORBERS
Take the plastic bushing
from the shock plastic
parts tree.
Take the plastic bushing
from the shock plastic
parts tree.
M3
Nylon Nut
M3
Nylon Nut
M3
Nylon Nut
M3
Nylon Nut
3X20mm
Cap Screw
3X20mm
Cap Screw
3X20mm
Screw
3X20mm
Screw
3X25mm
Cap Screw
3X25mm
Cap Screw
3X25mm
Screw
3X25mm
Screw
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
30702
40056
35313
90018
90018
30702
35313
40056
35313
35313
30702
90018
90018

40117
Body Support
Plastic
40117
Body
40117
Body
40117
Body
40117
Body Post
Plastic
ASSEMBLY OF THE BODY POST
4x12mm
Hex Screw
4x20mm
Hex Screw
4x20mm
Hex Screw
4x20mm
Hex Screw
4x12mm
Hex Screw
4x12mm
Hex Screw
4x12mm
Hex Screw
3x12mm
Hex Screw
3x12mm
Hex Screw
3x12mm
Hex Screw
..........X4
..........X2
..........X2
..........X2
2.6x15mm
Screw
2.6x15mm
Screw
2.6x15mm
Screw
..........X2
..........X2
M4
Nylon Nut
M4
Nylon Nut
M4
Nylon Nut
M3
Nylon Nut M3
Nylon Nut
M3
Nylon Nut
(FRONT)
(REAR)
94004
94010
35313
94010
94042
94012
35313
94042
94004
94010
94012
35313
94012
94010
94042
94004