Ohenry Productions 20x20 User manual

Ohenry 20’x20’ High Peak Frame Tent
Ohenry Productions Inc. 3859 Chappel Hill Rd. Waco, TX. 76705
[phone] Oce [phone] Fax

Ohenry 20’x20’ Frame Tent
Ohenry Productions Inc. 3859 Chappel Hill Rd. Waco, TX. 76705
[phone] Oce [phone] Fax

Fittings
4 Corner Fitting
18 Way Crown
4Side T Joint
8 Premium Base Plates
54 Canopy Pins
8 Guy Ropes
8 24” Stakes
8 1” Ratchets
Poles
4 14’ 4” Hip Rafters
4 10’ 6” Rafters
8 9’ 4” Spreaders
8 6’ 8” Legs
Part Identication
8 Way Center Crown Premium Base Plate
Side T
1” Ratchets
Corner Fitting Canopy Pin
Mast Parts
1 End Masts
1 End Mast Inserts
End Mast End Mast Insert

Ohenry Productions Inc. 3859 Chappel Hill Rd. Waco, TX. 76705
[phone] Oce [phone] Fax
14’ 4” Hip Rafter
9’ 4” Spreader
14’4” Hip Rafter
10’ 6” Rafter
9’ 4” Spreader9’ 4” Spreader

Ohenry Productions Inc. 3859 Chappel Hill Rd. Waco, TX. 76705
[phone] Oce [phone] Fax
“OHENRY WEST COAST FRAME TENT” ASSEMBLY INSTUCTIONS
10’ wide – 20’ wide
All tubing is labeled for easy Identication.
Please verify the parts with the chart provided before you begin assembly.
Assembly Steps:
1. Lay out the Spreader pipes and Corner Fittings in a square or rectangle (refer to previous page). Lay out Hip Rafters and Rafters
and Side T Joints. Place Center Crown(s) in the center of the tent.
2. Start assembling the frame by inserting and pinning the Hip Rafters into the Center Crown(s). If assembling a rectangular frame
insert and pin the appropriate Spreader into the Center Crown and continue to the next Ridge Top T or Center Crown. Insert and pin
Rafters into the Crowns and Ridge Top T’s. Insert and pin all Corner Fittings and Side T Joints to the bottom of the Hip Rafters and
Rafters.
3. Start at one corner of the frame and insert and pin the Corner Fitting to the Spreader. Continue in one direction around the frame
inserting and pinning each tting to the Spreaders.
4. Unfold the tent cover on the ground next to the assembled frame. Place the cover on the frame. Be sure to center the cover
while the upper structure is still on the ground.

5. Lift one side of the tent and attach the legs (with base plates) and insert the pins. It is recommended that two people be available
when lifting the frame to install legs.
6) Take the Mast Insert
and insert it into the 3-way
crown from the Top of the
6-way Center Crown.
7) Secure the Mast Insert to
the center crown with the
strap and buckle provided
so the insert doest move
when you insert the mast
later.
8) Remove the top cap
from the round End Mast
and insert the mast into the
Mast Insert from the bottom
(underneath the tent).
9) Take the removable mast
top with pin, insert pin
through the hole in tent top,
then insert the top piece into
the mast and pin in place
with the canopy pin.
10) Next push the mast all
the way up untin thetwo
holes in the Mast Insert
align with the two holes at
the bottom of the mast. Se-
cure with two canopy Pins.

12) Next you will attach the end of the ratchet strap which has the metal clip (ratchets are included with your tent top) to the
rings in the tent top at the corners and depending on size, the other locations on the tent top perimeter which have rings attached.
Next attach the other end of each ratchet which has a ring attached to the base as shown in the photograph below. Tighten ratchet
enought to have a slight tension. Do the same for each leg. Be sure tent is aligned correctly on the frame, and then retighten all the
ratchets attached to the tent top and base plates as shown.
11. Lift the other side of the tent and attach the legs (with base plates).
12. At each leg, now drive a tent stake into the ground about 5’ from the edge of the tent. Attach the Guy Ropes provided with
your tents and tighten securely to the tent stake. provided. In the event of high winds, the cover should be removed
from the frame to prevent damage to your tent. Your tent should be vacated during inclement weather.
Ohenry Productions Inc. 3859 Chappel Hill Rd. Waco, TX. 76705
[phone] Oce [phone] Fax