Okamura Alsos Beans 8610AZ User guide

Assembly precautions
Installation precautions
Handling precautions
Cleaning precautions
● Be sure to carefully read these assembly and usage instructions to ensure correct assembly of this product.
Incorrect assembly is dangerous and could cause the chair to flip over, resulting in an injury or damage.
● Position the product on a level, stable surface. If you use the product on an inclined or unstable
floor, it may cause the product to fall over or result in an accident.
● Avoid using the product in places exposed to direct sunlight, high temperatures, or high
humidity, as it may cause deterioration, deformation, or discoloration.
Also, do not bring the chair near the open flame of heaters or other devices. The seat fabric
could ignite, resulting in a fire.
● Do not bring a cutter knife or sharp object into contact with the backrest or seat fabric. This
could result in a snag or rip in the fabric.
● Do not insert your hands or fingers into the gaps of the movable parts. They could get pinched
in between, resulting in an injury.
● Do not attempt to disassemble or modify this product.
● If you notice any looseness in the set screws or other parts when using, immediately retighten
them.
Continued usage with loose parts is dangerous because the parts could fall off, causing the
chair to flip over, resulting in an injury or damage.
● If the chair feels unstable, makes an unusual sound, or otherwise feels abnormal, immediately
stop usage, and contact the dealer where you made the purchase.
● For the upholstery type, fabric is coated with water-repellent. If you spill water on the product,
immediately wipe it off. If left unremoved for an extended period, water may soak into the
product.
● When cleaning the fabric, either slap the fabric with your hands to dislodge the dust, or use a
vacuum cleaner to remove the dust. To remove stains, use a commercially-available fabric stain
remover.
● To clean the metal and plastic parts, wipe with a soft, dry cloth. If the parts are extremely dirty,
wipe it with a small amount of mild detergent mixed with water, then wipe it with a well-wrung
cloth to thoroughly remove all water and detergent.
● Never use alcohol or thinner-based solvents to wipe the chair parts. They could damage the
surface.
● Do not handle this product roughly or use it for other than its intended purpose.
Do not use the
chair as a platform
for carrying objects.
Do not try to sit on the
backrest or sit
backwards on the chair.
Do not stand on the
chair by using it as a
stool.
Example
Okamura alsos Beans chair
Assembly/Instruction Manual
Thank you for purchasing an Okamura alsos Chair.
Carefully read and understand the contents of this Assembly/Instruction Manual to ensure proper assembly
and use.
For Your Safety
(Please observe the safety precautions)
Caution
This denotes information of situations that
may result in injury or physical damage if the
warnings are ignored or the product is used
improperly.
Also denotes hazardous situations that may
result in serious injury.

Step 1
Step 2 Step 3
Step 4
Backrest
(Upholstery type: Fabric
with water-repellent
coating)
Insert the gas cylinder (with cover) onto the base. Insert the gas cylinder into the hole in the bottom of the seat.
Sit on the seat so that the seat is inserted all the way onto the
gas cylinder.
Seat
(Upholstery type: Fabric
with water-repellent coating)
Gas cylinder (with cover)
Base
Mount the seat onto the gas cylinder
Assembling the alsos Beans Chair
Check the parts
Mount the gas cylinder onto the base
Mount the backrest onto the seat
Loosen the knob, lower the support bracket,
then insert the backrest onto the rails on the
rear of the seat.
Firmly tighten the knob to secure the backrest
into place.
Knob
Loosen
Tighten
Indicator
*When tightening the knob, check that the
indicator scale matches the child's height.
(See the adjustment procedure.)
Support
bracket
*If it is difficult to insert the
backrest, loosen the knob,
then lower the support
bracket further.

Step 1 Check!
Step 2
● The alsos Beans chair is a swivel study chair that supports
JIS standard sizes 2 to 5 (heights from 120 cm to 165 cm)
for school furniture.
The seated height, seated depth, and backrest height can
be adjusted to any setting to match the child's growth for
enabling usage with correct posture.
JIS:Size 2
(Height 120 cm)
JIS:Size 5
(Height 165 cm)
Backrest
Seat
Base
Loosen
Tighten
Casters
The numbers on the
indicator correspond to
the height (cm).
Height (cm)
Backrest
Knob
Seat height
adjustment
lever
Indicator
Adjust the height of the seat
What is the correct sitting posture?
Adjust the depth and height of the backrest
*The numbers are general
guidelines only. Adjust to a
position where the child sits
with correct posture.
Pull up the seat height
adjustment lever to adjust the
height of the seat.
Loosen the knob, and slowly slide the backrest, and then firmly close
the knob to lock it at the position where the bulging section of the
backrest contacts the back of the child.
First, lower the seat to the lowest
position, allow the child to sit on
it, and then raise the seat to a
height where the child has the
correct sitting posture.
*To lower the seat, apply body weight to the center of the seat.
*The product design uses a gas cylinder with high reactive force (force raising the seat),
and so the seat does not lower unless the person sitting has a weight of 35 kg or more.
Product Features
Names of Parts
Adjustment Procedure (Adjustment should always be performed by an adult to ensure the correct sitting posture.)
Size
Standard height
Seat height
Seat depth
Desk is at same
height as elbows
Feet are flat on the
floor
Gap of about two finger widths
between the edge of the seat
and the back of the knees
Backrest
contacts the
child's back
Knees are
bent at an angle
of about 90°
Gap of about one
child's fist length

Okamura Corporation
International Sales and Marketing Div.
9F Kokusai-Shin Akasaka Bldg. East, 2-14-27 Akasaka
Minato-ku, Tokyo 107-0052 Japan
http://www.okamura.co.jp