Okamura credenza User manual

GD2922
2019-01
Instructions for Use
Conference Furniture
INTERNATIONALSALES&MARKETINGDIVISION
2-14-27,Akasaka,Minato-ku,Tokyo107-0052,JAPAN
Tel:[phone]Fax:[phone]
http:
//
www . okamura.jp
/
OKAMURACORPORATION
Materials and Surface Finish
Part Materials Surface finish
Veneer top board
Surface Wood veneer Urethane coating
Edge Wood edgebanding
Core MDF ―
Laminate top board
Surface High pressure laminate ―
Edge PVC edgebanding ―
Core MDF ―
Solid surface top board
Surface
Solid surface
―
Edge ―
Core ―
Glass top board
Surface
Tempered glass
―
Edge ―
Core ―
Veneer case/doors/shelves
Surface Wood veneer Urethane coating
Edge Wood edgebanding
Core MDF ―
Laminate case/doors/shelves
Surface High pressure laminate ―
Edge PVC edgebanding ―
Core MDF ―
Legs Aluminum Polished
Please understand that product specifications might change without prior notification due to improvements made
to the product.
For daily care
Wooden part
●Wipe gently along the grain with a soft, clean,
dry cloth.
●If the product becomes noticeably dirty,
remove the dirt using a soft cloth dampened
with water, then use a dry cloth to absorb
water residue.
●For a more thorough cleaning we recommend
using a mild cleaner (thin neutral detergent).
〈Caution〉
●Do not use the following as they may damage
the coating.
◎ Thinner, benzene, alcohol , lacquer, oil,
vinegar, boiling w ater, polis her, e t c.
●Frequent wiping with a damp cloth may cause
cracking of the coating. It is recommended
to use a dry soft cloth or our wiping cloths for
daily care.
Resin part
●Wipe off with a soft cloth dampened with
water.
●When it gets dirty, moisten the cloth with thin
neutral detergent and squeeze it hard to
wipe.
Wipe clean with a damp cloth. Be sure to
wipe detergent completely and wipe again
with a dry cloth to dry it.
Aluminum part
●Wipe off with a dry soft clean cloth.
●If moisture is collected or substances such
as fingerprints or sebum are adhered,
wipe it off immediately. Leaving moisture,
liquid, fingerprints, or sebum on the surface
accelerates oxidation of the aluminum part
and deteriorates gloss and texture.

1 2
Part names
Safety Instructions (Make sure to follow these instructions)
Caution
User must follow this instruction to prevent accidents and injuries, or damages to
their property.
Caution ●Many chemical substances will be released by the product when it is first purchased. Sufficiently
ventilate or expose the product to moving air for some time after purchasing it.
●Do not completely close windows when using the product in rooms with conspicuously high
temperatures/humidity (the benchmarks for these are temperatures in excess of 28°C (82.4°F) and
relative humidity in excess of 50%).
Appropriate Ventilation Measures
Installation
Please follow instructions below.
Failure to do so may cause serious damage to the product and Okamura will have no
responsibility for any disadvantages.
Characteristics of Natural Wood
As natural wood is a natural material, each color and grain pattern is unique. The protective
surface coating increases the durability of the product, giving a soft and subdued color and texture
of the natural wood. Depending on the wood, the color varies due to its natural characteristics. The
wood color grows rich and elegant over time. Some products may have a noticeable wood smell.
High humidity may lead to mold growth. Ventilation on a regular basis is recommended. Ensuring
you understand these characteristics, please read these Instructions for Use carefully before
installation and use.
* Natural wood includes solid wood, wooden veneer, artificial veneer, plywood, molded ply wood, laminated
wood, and MDF.
Do not handle roughly, or use
improperly. It may cause injury or
damage.
●Do not use as a stepstool.
Do not put your fingers or hands into
the spaces of the product. Your fingers
or hands may get caught.
Be careful of the following items since
they may cause injury or damage the
product.
●Do not sit or lean on to the product.
●If the product is found unstable due to
loosening of bolts or screws, retighten them.
●Do not use the product with any part loose or
missing.
Observe the following when moving or
storing the product.
●Do not move the product while objects are
placed on it.
●Be sure to move the main body with more
than two people.
●When using the leveler, ensure that more
than two people provide rigid support using
extreme caution so as to prevent your fingers
or toes from getting caught.
Do not disassemble or repair on your
own.
●Do not attempt to disassemble or repair the
product yourself. Please contact our official
dealers when needed.
●Do not use with bolts and screws loosen.
Failure may cause damage to the product
and result in injury.
Do not modify on your own.
Do not attempt to modify the product
yourself. Please contact our official
dealers when needed.
●Modifying the product by yourself may cause
the product to malfunction or may cause
accidents or injuries.
Okamura is not responsible for any damages
caused by modification.
●Please contact an official Okamura dealer in
advance when needed.
Uneven loading on the product may
cause balance loss and thus drop or
fall.
Use the product indoors.
●Do not use outdoors or near water. Failure to
do so may cause warping or mold.
Do not expose the product to direct
sunlight. It causes distortion or
discoloration of the product.
●Always use curtains, blinds, or the like to
protect the product from direct sunlight when
placing it next to windows or the like.
Avoid high temperature, high humidity,
or extraordinary aridity.
Do not place the product under a heater
or air-conditioner exhausting high
temperature air.
Place the product on a horizontal
surface.
●Be sure to place the product on a horizontal
surface. Failure to do so may cause
deformation of the product or damage to the
moving parts.
●Use the leveler to keep the product horizontal
to the floor surface.
Aluminum base
Plinth base
Top board Interior shelves
Top board
Door
Leveler
Leveler

43
Operation Guide
Please follow instructions below. Failure to do so may cause serious damage to the product
and Okamura will have no responsibility for any damages.
Operating Precautions and Maintenance
Instructions to Extend the Life of Product
●Do not place an ashtray, a vase or a metallic
object directly on the coating as this may
cause scratches to the surface.
In particular, note that porcelain and pottery
have a rough surface on their bottoms.
●Do not use in places exposed to vapors.
This could cause rusting.
●If the product gets wet with water, wipe off
with dry and soft cloth.
●If you spill tea, coffee, detergent, medicine,
or some other liquid on the product, wipe off
immediately.
●This instruction manual is very important, so
store it in an easily accessible location.
●Regular maintenance is recommended for
long product life.
Make requests to us immediately when a
repair or inspection is needed (fees required
after expiration of warranty).
●If the product is found unstable due to loose
bolts and screws, tighten them.
●Do not use sharp objects such as a knife on
the top board as it may cause scratches or
damages to the surface.
●Avoid writing directly on the wood veneer
top board. Be sure to use a desk pad when
writing. Failure to do so may damage the
surface.
●Do not use a PVC desk mat as this causes
discoloration or deformation of the coating.
■Adjusting the door hinges
Up and down adjustment Sideways adjustment In and out adjustment
The door hinges can be adjusted in three ways.
■Opening/closing the doors
Open or close the doors by holding on the
open marks indicated on the top of the
doors.
The doors open to 110 degrees.
Be careful not to get your fingers caught
in the door when the door is closing.
Caution
Open marks
■Adjusting the shelf height
Shelf pegs
Shelf
Notch
The shelf height can be adjusted on 1 1/4"
increments.
When you change the shelf height, insert the
shelf pegs into the holes of the same height,
and install the shelves so that the notches in
each corner fit in the pegs.
Do not climb on the shelves. Doing so
may cause the shelf boards to come off,
resulting in injury.
Caution
■Level adjustment
Turn the leveler located under the base to
adjust the height between 0" and 3/8". Be
sure to keep the product horizontal to the
floor surface by using the leveler.
Leveler
Lower
Higher
Be sure to perform height adjustment
with more than two people using extreme
caution so as to prevent your hands and
fingers from getting caught.
Caution
■Cable management
Cable openings are provided at the bottom
boards, the shelves, and the dividers for
clean cable management.