Okamura 865XTW User guide

3-drawer Wagon
865XTW
Assembly/Instruction Manual
Important Document
Diagram of assembled wagon (names of parts)
Thank you for purchasing an Okamura 3-
drawer Wagon. Carefully read and
understand the contents of this Assembly/
Instruction Manual to ensure proper
assembly and use.
A cross-head screwdriver is required for
assembly. Have one ready before you begin.
* Do not use an electric screwdriver for
assembly, as it could damage the product
Caution label
(Do not remove the caution label.)
(Attached to wagon
top panel)
Product serial number sticker
(Attached to bottom plate)
Drawer unit
Lock
Upper drawer
Middle drawer
File drawer
Caster
Caster
(with stopper)
Single-end connection bolt
Caster
(without stopper)
Nut cap
Divider
(These are already installed
in the file drawer.)
Key
Wagon
For safety reasons, the length that the upper drawer
can be pulled out is slightly less than that for the
middle drawer and file drawer.
Use a cross-head screwdriver for assembly.
Do not use an electric screwdriver or power tools,
as they may damage the product. Use a manual
screwdriver instead.
Wagon
Drawer unit
Parts list (Make sure to check the information below before you start assembling.)
Screw-type
connector
Arrow
Single-end connection bolt
Tighten
Loosen
Note about screw-type connectors
Screw-type connector
Turn clockwise to tighten.
Turn counter-clockwise to loosen.
(Embedded in various parts)
When the arrow is aligned with the
connecting bolt, it can be inserted
(or removed).

For Your Safety (Please observe the safety precautions)
Caution
Caution
Assembly precautions
Handling precautions
Installation precautions
Ensuring long-term use
Cleaning precautions
To ensure proper assembly, carefully read and
understand this manual beforehand, use a
screwdriver to securely tighten all bolts, and
make sure to use all of the specified parts.
Do not use an electric screwdriver for
assembly. If too much force is applied, it could
damage the product or make it impossible to
remove the bolts later.
Depending on the type of assembly, there may be
some unused parts or materials left over. Store
these items carefully, as they may be required when
reconfiguring the product If any parts become lost,
they will need to be repurchased.
After assembly, place the product on a level
surface, securely tighten all bolts, and make
sure that all parts are securely attached.
Do not handle the product roughly, and do not
use it for any purpose other than the intended
use. Never climb or lean heavily on the
product. Doing so may damage the product or
cause it to fall over.
Position the product on a level, stable surface.
If you use the product on an inclined or
unstable floor, it may cause the product to fall
over or result in an accident.
Do not place hot objects directly on the product.
Doing so may cause deterioration, deformation,
or discoloration.
Do not allow the product to remain wet for long
periods of time, and do not leave wet items
such as a damp cloth on it. Doing so may
deform, stain, or corrode the surface. If the
product becomes wet, immediately wipe it dry.
Do not apply stickers, tape, or other adhesive
materials to the product. Doing so may cause
the surface to peel.
Wipe with a well-wrung cloth. If the product is
extremely dirty, wipe it with a small amount of
mild detergent mixed with water, then wipe it
with a well-wrung cloth to thoroughly remove all
water and detergent. If a significant amount of
water remains on the product, it may deform or
discolor the surface.
Never use alcohol or thinner to clean the
product, as they may damage the surface.
Avoid using the product in places exposed to
direct sunlight, high temperatures, or high
humidity, as it may cause deterioration,
deformation, or discoloration.
Do not scrape the product with hard objects,
and do not use sharp writing instruments
without placing a writing mat or other protection
under the paper. Doing so may deform or
scratch the surface.
Periodically check for loose bolts and parts,
and retighten as necessary. Using the product
with loose bolts or parts could damage or
deform the product, or cause it to fall over.
This product uses natural wood. Because it is a
natural material, natural wood has a wide variety
of grains and shades. The surface of the material
was also treated for protection and for providing
enhanced durability as furniture. Please be aware
of these unique characteristics as you use this
product over a long time.
When placing objects on the product, make sure not to exceed the maximum load weight. If the maximum load weight is exceeded, it may
damage the product or cause it to fall over.
The maximum load weight of the desktop is 20kg.
A newly purchased product may smell of the
substances used in the adhesives and coating.
Periodically ventilate the room until the smell
subsides.
Before detaching the top section of the
separable wagon, make sure that the arrows
on the screw-type connectors are pointing
down.
This denotes information about a situation that may result in injury or physical
damage if the caution is ignored or the product is used improperly.

Assembling and using the wagon
Attaching the casters
Mounting the Drawer Unit to the Wagon
Insert the casters into the mounting holes located on
the bottom of the wagon and under the front panel of
the file drawer.
When mounting the drawer unit to the wagon, attach
the nut caps in the nut holes at the four locations
on the rear panel of the wagon.
Wagon
Bottom
of the
wagon
Rear panel
Protective sheet
*The protective sheet is not included and must be supplied by the customer.
Front panel
Front panel
Drawer unit
* Casters are available in two types -- casters with
stoppers and without stoppers.
When mounting the drawer unit to the top panel of the wagon When mounting the drawer unit to the rear panel of the wagon
Removing the dividers
●For sizes of JIS4 or larger ●For sizes of JIS2 of JIS3 which cannot fit under
the desk top panel
Screw in the single-end connecting bolts to the four
locations on the top panel of the wagon, connect the
drawer unit, and firmly tighten the screw-type connectors
at the four locations.
When drawer unit is
mounted to wagon top
panel
When drawer unit is
mounted to wagon
rear panel
Lock the drawer unit, and check that the drawer does not
open. Screw in the single-end connecting bolts to the four
locations on the rear panel of the wagon, mount the drawer
unit to the rear panel, and firmly tighten the screw-type
connectors at the four locations.
Attach the nut caps to the wagon
top panel.
*Be careful not
to over tighten
the single-end
connecting
bolts.
● To change the mounted location of the drawer unit, loosen the four screw-type connectors, remove the
drawer unit, and remount by following the above instructions.
Lock the drawer
Drawer unit
Screw-type
connector
Screw-type
connector
Wagon
Simply pull up on the file
drawer dividers to
remove them.

Troubleshooting
Why am I having difficulty with
assembly?
Why don't the parts fit?
Why are there parts left over after
assembly?
Depending on the type of assembly,
there may be some unused parts or
materials left over. Store these
items carefully, as they may be
required when reconfiguring the
product.
Why does the wood grain or color
look different from what I expected?
Why is the product different from
the display items and photographs?
Make sure to follow the procedures
in the instruction manual. Make sure
that you are using the correct parts
and that they are oriented properly.
The color or wood grain of the
product may differ slightly from the
catalog or sample product.
Okamura Corporation
International Sales and Marketing Div.
9F Kokusai-Shin Akasaka Bldg. East, 2-14-27 Akasaka
Minato-ku, Tokyo 107-0052 Japan
http://www.okamura.co.jp