Oklahoma Sound WM-100H User manual

Manufacturers Warranty
Our WIRED/WIRELESS MIC undergoes the most
rigid and exacting tests for superior quality and
performance before leaving the factory.
Oklahoma Sound Corporation warrants this
product to be free from defective material and
workmanship for two years from the date of
resale by an authorized Oklahoma Sound distrib-
utor. Oklahoma Sound will replace defective parts
and repair malfunctioning products under this
warranty when the defect occurs under normal
installation and use, provided the unit is returned
to our factory via prepaid transportation after
direct authorization and approval by Oklahoma
Sound. This warranty provides that examination
of the returned product must disclose in our
judgement, a manufacturing defect. This warran-
ty does not extend to any product which has been
subject to misuse, neglect, accident, improper
installation, or where the serial number has been
removed or defected and is given in lieu of any
other warranty implied or expressed and will not
cover any consequential damages.
INSTRUCTION MANUAL
MODEL #WM-100H
OKLAHOMA SOUND CORPORATION
PACKAGE CONTENTS
Your Unit should Contain the Following:
• One Microphone
•One Wireless Antenna
• One 14' Cable
• One Transmitter
• One AA Battery
•One AAA Battery
4
WIRED/WIRELESS Microphone System
5
FEATURES
A) ON/MIC/OFF SWITCH
B) MICROPHONE LAMP
C) MICROPHONE HOUSING
D) XLR MALE CONNECTOR
E) 14' CABLE
F) PRONG OF 14' CABLE
G) ANTENNAE FOR
WIRELESS USE
H) WIRELESS TRANSMITTER
I) ADAPTER FOR
WIRELESS TRANSMITTER
J) ON/OFF SWITCH FOR
WIRELESS TRANSMITTER
K) WIRELESS TRANSMITTER
LAMP
L) FREQUENCY ADJUSTER
REFER TOPICTURE AND LABELING OF PARTS FOR ASSISTANCE IN OPERATION
Wired / Wireless
Mic System
Microphone used as Wired System
B
A
F
D
E
C
Microphone used as Wireless System
G
H
JL
K
I

OKLAHOMA SOUND CORPORATION
INTRODUCTION
Congratulations! You are now the owner of
the unique Wired/Wireless Microphone
System from Oklahoma Sound Corp.
Use the microphone together with the
included 14' cable, or if you prefer, you can
free yourself from the restraints of wires by
simply going wireless.
This state-of-the-art microphone system
should provide trouble free usage for years
to come. If you experience any difficulty with
our product, or have questions, please call
our customer service at 973-594-9000.
OKLAHOMA SOUND CORP.
149 Entin Road, Clifton NJ 07014
Tel [phone] • Fax [phone]
www.oklahomasound.com
2
WIRED/WIRELESS Microphone System
7
OKLAHOMA SOUND CORPORATION
6
WIRELESS PA: Voice Amplification System
3
TABLE OF CONTENTS
Introduction ..............................................................2
Package Contents.................................................4
Product Features......................................................5
Operating Instructions — Wireless Use..................6
Operating Instructions — Wired Use.................... 7
Manufacturer’s Warranty ...................................... 8
WIRELESS USE
Assembling the parts—
MICROPHONE
A. Screw off microphone housing (labeled ‘c’) from mic
B. Insert battery (AA) into battery chamber of mic
C. Screw housing back onto microphone
D. Connect wireless antenna (labeled ‘g’)to XLR male
connector (labeled ‘d’)
TRANSMITTER
A. Open batterychamber of transmitter; insert battery
correctly and close battery chamber
C. Insertadapter of wireless transmitter (labeled i) into your
existing amplifier's jack.
Using the wireless microphone—
A. Turn Microphone switch (labeled ‘a’) to the "ON" posi-
tion. Red lamp should be illuminated.
B. Turntransmitter switch to the "ON" position. Red lamp
should be illuminated.
C. If acoustic quality and volume are abnormal or receiv-
ing distance is decreased, check first to see if replacing
batteries rectifies problem. If problem still persists then try
"trimming" the frequency of transmitter by carefully
adjusting the frequency adjuster (labeled ‘L’) with a
small screwdriver. (Note: The frequency adjuster is on
the same side as the transmitter lamp)
WIRED USE
(with included cable)
Assembling the parts—
A. Unscrew microphone housing (labeled ‘c’).
B. Remove battery from battery chamber and mount
housing back onto microphone.
C. Connect prong of 14' cable (labeled ‘f’) to XLR male
connector (labeled ‘d’).
D. Connect adapter of 14' cable to your existing ampli-
fier system.
Using your microphone in wired mode—
Turn microphone switch (labeled ‘a’) to "Mic".
(Note: microphone will not work in wired mode if
switch is turned to "On"; it must be turned to "MIC" for
normal operation).
CAUTION
In the event the microphone will not be used for
an extended period of time, battery should be
removed so as to avoid battery deterioration
and damage to components.