OKPOS ZED-POS User manual

We use the original version of Microsoft windows OS
and recommend customers to use them.
MANUAL
SERVICE
www.okposkorea.com

Dual Monitor
HDD Disk Recovery
Installation
ZED-POS
I-POS
Z-POS
K-POS
Accessary
VFD
3P
6P
9P
12P
18P
15P
16P
17P
Contents

RearFront

ZED POS
Cable Holder
Stand
Rear Cover
Dual Monitor
(optional)
Cable Cover
MSR Reset
Button
2 X USB Port
MSR
Power Signal
Error Signal
HDD Signal
Power Signal
Power Button
I/O Port
Serial Port
(RJ45-COM4)
DC-IN Power
(12V)
DC-OUT Power
(12V)
VGA Port
USB PortSerial Port(DSUB9-COM3)
Speaker Port
PS/2 Mouse, Keyboard LAN
Serial Port(DSUB9-COM1)
Serial Port(DSUB9-COM2)
Reassemble the cable cover
Reassemble the stand rear case
Activate the system by pressing the power button
5
6
7
Hold tightly, and pull up the rear cover for detaching
Push up the cover by press the PUSH parts of
cable cover for detaching
Insert the Power adapter cable to power port by following
the direction of the arrow ③
Connect the peripheral cables to I/O ports on demand
A
1
1
2
3
4
System Installation and Turn-on/off
Cable Cover
Stand
Rear Cover
1
2
A
B
3
Make sure the adapter direction before plugging in CAUTION
3
Service Manual


ZED POS
Remove the cable cover
Install a dual monitor by sliding it to the direction of arrow ②
1
2
Fasten the screw with a coin or driver
3
Installation
1
3
Connect the VGA cable and dual power cable
Reassemble the cable cover after connecting power adaptor cable
1
2
Connecting Cable

Remove the cable cover and stand rear case
Detach the stand dual set-up part. Clear up the edge when it detached
Fasten the screw after install the dual monitor on the stand
1
2
3
Installation
1
3
Connect the VGA cable and dual power cable
Reassemble the cable cover after connecting power adaptor cable
1
2
Connecting Cable
4
Service Manual


ZED POS
Wear protective gloves when you detach the storage device from the bracket. The edge of bracket is very sharp and it may cause hurt.
Make sure to turn off the system power before disassembling of HDD from the system.
CAUTION
Please follow the below instruction if you need to replace the storage device (HDD Disk or SSD)
Storage Disassembly
Detach the cable cover
Unfasten the hand screw following the direction of arrow ②
Hold the hand screw and pull out of the HDD to the direction of arrow ③
Disassemble HDD from the bracket
1
2
3
4
4
3
2
1
2
1
1
Detach the MSR connecter
Unfasten the screw with a coin or
(-) shaped driver
1
2
MSR Disassembly (Optional)
4
31
Lift up the fixing lever
Pull the stand to the direction of arrow
③
Disassemble the stand by lifting up
Unscrew it with a coin or (-) shaped driver
1
2
3
4
Stand Disassembly
5
Service Manual

Cable Holder
Stand
Rear Cover
Dual Monitor
(optional)
Cable Cover
MSR Reset
Button
2 X USB Port
MSR
Power Signal
Error Signal
HDD Signal
Power Signal
Power Button
RearFront

I POS
6
Service Manual
I/O Port
Serial Port
(RJ45-COM4)
DC-IN Power
(12V)
DC-OUT Power
(12V)
VGA Port
USB PortSerial Port(DSUB9-COM3)
Speaker Port
PS/2 Mouse, Keyboard LAN
Serial Port(DSUB9-COM1)
Serial Port(DSUB9-COM2)
System Installation and Turn-on/off
Reassemble the cable cover
Reassemble the stand rear case
Activate the system by pressing the power button
5
6
7
Hold tightly, and pull up the rear cover for detaching
Push up the cover by press the PUSH parts of
cable cover for detaching
Insert the Power adapter cable to power port by following
the direction of the arrow ③
Connect the peripheral cables to I/O ports on demand
A
1
1
2
3
4
Make sure the adapter direction before plugging in CAUTION
1
2
A
B
Cable Cover
Stand
Rear Cover
3
4

Installation

I POS
Remove the cable cover
Install a dual monitor by sliding it to the direction of arrow ②
Fasten the screw with a coin or driver
1
2
3
12
3
Connecting Cable
Reassemble the cable cover after connecting
power adaptor cable
2
Connect the VGA cable and dual power cable
1
7
Service Manual


I POS
Wear protective gloves when you detach the storage device from the bracket. The edge of bracket is very sharp and it may cause hurt.
Make sure to turn off the system power before disassembling of HDD from the system.
CAUTION
Please follow the below instruction if you need to replace the storage device (HDD Disk or SSD)
Storage Disassembly
Detach the cable cover
Unfasten the hand screw following the direction of arrow ②
Hold the hand screw and pull out of the HDD to the direction of arrow ③
Disassemble HDD from the bracket
1
2
3
4
4
3
2
1
When MSR (Card Reader) mounted, please
note that the cable can be caught in the case
CAUTION
MSR Disassembly (Optional)
Detach the MSR connecter
Unfasten the screw with a coin or
(-) shaped driver
1
2
2
1
1
To safe use, fixed latch in holeCAUTION
Stand Disassembly
Lift up the fixing lever
Pull the stand to the direction of arrow ②
Disassemble the stand by lifting up
1
2
3
2
1
3
8
Service Manual

Cable Holder
Stand
Rear Cover
Dual Monitor
(optional)
Cable Cover
MSR Reset
Button
2 X USB Port
MSR
Power Signal
Error Signal
HDD Signal
Power Signal
Power Button
RearFront

Z POS
I/O Port
Serial Port
(RJ45-COM4)
DC-IN Power
(12V)
DC-OUT Power
(12V)
VGA Port
USB PortSerial Port(DSUB9-COM3)
Speaker Port
PS/2 Mouse, Keyboard LAN
Serial Port(DSUB9-COM1)
Serial Port(DSUB9-COM2)
System Installation and Turn-on/off
Cable Cover
Stand
Rear Cover
1
2
A
B
3
4
Make sure the adapter direction before plugging in CAUTION
Reassemble the cable cover
Reassemble the stand rear case
Activate the system by pressing the power button
5
6
7
Hold tightly, and pull up the rear cover for detaching
Push up the cover by press the PUSH parts of
cable cover for detaching
Insert the Power adapter cable to power port by following
the direction of the arrow ③
Connect the peripheral cables to I/O ports on demand
A
1
1
2
3
4
9
Service Manual

Installation

Z POS
Remove the cable cover
Install a dual monitor by sliding it to the direction of arrow ②
Fasten the screw with a coin or driver
1
2
3
12
3
Connecting Cable
Reassemble the cable cover after connecting
power adaptor cable
2
Connect the VGA cable and dual power cable
1
10
Service Manual


Z POS
Wear protective gloves when you detach the storage device from the bracket. The edge of bracket is very sharp and it may cause hurt.
Make sure to turn off the system power before disassembling of HDD from the system.
CAUTION
Please follow the below instruction if you need to replace the storage device (HDD Disk or SSD)
Storage Disassembly
Detach the cable cover
Unfasten the hand screw following the direction of arrow ②
Hold the hand screw and pull out of the HDD to the direction of arrow ③
Disassemble HDD from the bracket
1
2
3
4
4
3
2
1
When MSR (Card Reader) mounted, please
note that the cable can be caught in the case
CAUTION
MSR Disassembly (Optional)
Detach the MSR connecter
Unfasten the screw with a coin or
(-) shaped driver
1
2
2
1
1
To safe use, fixed latch in holeCAUTION
Stand Disassembly
Lift up the fixing lever
Pull the stand to the direction of arrow ②
Disassemble the stand by lifting up
1
2
3
2
1
3
11
Service Manual

Cable Holder
Stand
Rear Cover
Dual Monitor
(optional)
MSR Reset
Button
MSR
2 X USB Port
Power Button
RearFront

K POS
I/O Port
Serial Port
(RJ45-COM4)
DC-IN Power
(12V)
DC-OUT Power
(12V)
VGA Port
USB PortSerial Port(DSUB9-COM3)
Speaker Port
PS/2 Mouse, Keyboard LAN
Serial Port(DSUB9-COM1)
Serial Port(DSUB9-COM2)
System Installation and Turn-on/off
Install the Stand-Rear-Cover
Turn on the system with the Power On button
Push down Stand-Rear-Cover and remove
Put the power adapter cable to the arrow
indicated, and insert into the power port
1
2
3
4
11
2
3
Make sure the adapter direction before plugging in CAUTION
12
Service Manual


K POS
Remove the stand rear cover by pulling After inserting both hands’ fingers into the upper part of Stand Rear Cover ( ①)
Remove the dual monitor cover by lifting up like the arrow ②
Unfasten the screws of clamp and to fix hinges like the arrow ③
Fasten the screws of clamp and to fix hinges after placing the dual monitor holder in a right way like the arrow ④
1
2
3
4
4
3
2
11
Installation
Install dual monitor cover on the position of ⑤
Fasten the screws after inserting dual monitor hinges into the holes of dual monitor cover like the arrow ⑥
5
6
9.7inch
15inch
6
5
Install dual monitor rear cover after connecting VGA and power cables.
Reassemble the cable cover after connecting power adaptor cable
1
2
Connecting Cable
2
1
13
Service Manual


K POS
After remove Stand-Rear-Cover, Loosen a screw and separate the HDD Disk
Storage Disassembly
2
1
Remove the cable and screw and lift up the monitor
Monitor Disassembly
1
2
Remove the screws and slide the MSR sideward
MSR Disassembly
2
3
1
1
14
Service Manual


SETTING
After connecting dual monitor, turn on power and boot by OS
Select “Screen resolution”
1
2
3
Installation (WINDOWS 7)
Select one among multi display
3
Turn on power and boot it using OS
After click the Windows start button, select ‘Setting’ ▶ ‘Control Panel’ in order and click the
‘Display’ icon on the ‘Control Panel’ screen
After ‘Display Registered Information’ screen appeared, click the ‘Advanced’ button on ‘Setting’ tab
After select <Display Config> tab, select ‘Display Configuration’
Choose Resolution of Primary Mode and Secondary Mode (default 1054X768@60)
Press the ‘Auto Detection’ button
1
2
3
4
5
6
Installation (WINDOWS XP)
<15inch Dual Monitor>
Power Button
Auto Detection
<9.7inch Dual Monitor>
Power Button
Auto Detection
Extended Mode:
LVDS [extend] VGA
Clone Mode:
LVDS [clone] VGA
15
Service Manual


SETTING
All system data will be deleted.
We recommend you to back up important data to an external hard disk before you run the recovery function on the device.
CAUTION
If you encounter problems in the program or system OS, the hard disk can be recovered to the
previous state or the factory state.
HDD Disk Recovery
Connect the keyboard and mouse to the system
After turning on the system, follow the 0n-screen instructions: press the keyboard <F11> when the
‘F11 to WinClon…’ message appears on the screen within 3 to 4 seconds (PC POST process)
When Winclon Appears on the screen, press <F2> key or <F3> on your keyboard or click the mouse to select
‘Recover recent state’ or ‘Recover initial state’
After entering the password, press the <OK> button to continue the recovery (Password: pos)
1
2
3
4
※ ‘Recover initial state’ is restored to the
factory default state.
※ ‘Recover recent state’ is restored to the
most recent backup of Windows.
16
Service Manual


SETTING
For the connection of POS and kitchen printer, please refer below
Kitchen printer
2 (White)
3 (Red)
4 (Green)
5 (Black)
6 (Blue)
8 (Blue)
4 (Blue)
3 (W/Green)
7 (W/Brown)
RXD
TXD
DTR
GND
DSR
CTS
SIGNAL
NAME
DB 9P
FEMALE (POS)
RJ45
(PRINTER)
3 (White)
2 (Red)
6 (Green)
5 (Black)
4 (Blue)
4 (Blue)
3 (W/Green)
4 (Blue)
7 (W/Brown)
TXD
RXD
DSR
GND
DTR
DTR
SIGNAL
NAME
DB 9P
MALE (PRINTER)
RJ45-COM4
(POS)
If a sharp one like a ballpoint pen is used in calibration, damage to the touch screen may occur. This is not the way to be recommended.CAUTION
If touch screen is not calibrated correctly, re-calibrate as follows
Touch Screen
Select ‘PenMount 6000 RS232’ in device selection tab to configure in ‘PenMount Control Panel’
Press ‘Standard calibration’ button in the coordinate calibration tab
4 Follow the on-screen instructions
After you click the Windows start button, select as follows: <Program ▶
PenMount Windows Universal Driver (WHQL) ▶ Utility▶ PenMount Control Panel>
1
2
3
4
17
Service Manual


VFD
Turn system off before disassemblingCAUTION
Remove the part
Cable Cover (I-POS) Cable Cover (ZED-POS)
VFD Manual Cable Hand
Screw x 2
Parts Description
*
Connect cable in ③
Attach VFD in the direction of the arrow
Fasten the hand screws
3
4
5
Separate the cable cover
After remove hinge cover, connect cable as below
1
2
Installation
5
4
3
2
1
I-POS ZED-POS
Connect the cable
Assemble cable cover
1
2
COM3
Complete ImageConnecting the Cable
3
2
1
In CMOS ADVANCED -> Serial Port 3 Configuration -> Set Serial Port 3 Power 5V
1 2 3
SETTING
18
Service Manual


VFD
Turn system off before disassemblingCAUTION
VFD Manual Dual Cover (K-POS) Screw x 2
Parts Description
Connect cable in ③
Attach dual cover
Connect VFD to fasten screw
3
4
5
Remove Rear cover andBack cover
After remove hinge cover, connect cable as below
1
2
Installation
5
4
3
2
1
K-POS
Connect the cable
Assemble cable cover
1
2
COM3
Complete ImageConnecting the Cable
3
2
1
In CMOS ADVANCED -> Serial Port 3 Configuration -> Set Serial Port 3 Power 5V
1 2 3
SETTING
19
Service Manual

Tel + 82-70-7425-9001, Fax + 82-2-6299-5447, URL www.okposkorea.com
#801-802, Ace High-End Tower 6, 234, Beotkkot-ro, Geumcheon-gu,
Seoul, Korea (08513)
Making our customers satisfied is utmost value of ours
No.1 Total solution Provider