Okuma STANDROID Manual

A - Vertical Supports (x2)
Setup Instructions
STANDROID
Identifying Parts (Monitor Not Included. *Optional Upgrades)
B - Hand Tool C - Top/Bottom Supports (x2) D - Cross Supports (x3)
E - Base w/ Mounting Posts
I - T-Bolt for Monitor
(size M4, M6, or M8, x2 ea.)
M - Tension Wire
Q - Case* R - Case-to-Counter Wrap
(Black or Printed*) S - Case-to-Counter Top
N - Hover Frame* O - Hover Graphic* P - Hover Frame Arms
w/ Wing-Nuts* (x2)
J - Leveling Bolt for Monitor
(size M4, M6, or M8, x2 ea.) K - Eye Nut w/ Wing Bolt L - Eye Bolt
F - Fabric (Black or Printed*) G - Monitor Profile Bar H - T-Bolt w/ Wing Nut (x2)

Setup Instructions
STANDROID
Frame and Fabric
Connecting the Frame
Installing the Fabric (F)
1. Connect 3-part Vertical Supports (A) with
plastic grommets facing out.
2. Using the Hand Tool (B), attach the top
and bottom Horizontal Supports (C) to the
Vertical Supports (A) by turning the screw
with the star-shaped hole clockwise.
PLEASE NOTE : Make sure the thin
groove is along the outer edge of
each piece so the groove is continuous
around the frame.
3. Using the Hand Tool (B), attach the Cross
Supports (D) in the same manner at the 2
joints in the Vertical Supports (A). PLEASE
NOTE: The 3rd Cross Support (D) is
included for added support or for use as a
spare replacement piece.
1. Make sure the frame is laying flat on the
floor and the star-holed screws are
facing down.
2. Start with each corner and attach Fabric (F)
by rolling fabric in and pushing the rubber
beading into the thin groove along the edge
of the frame with your thumb.
3. After the corners are secured, continue
pushing the rubber beading into the groove
along the sides, top and bottom of the frame.
PLEASE NOTE: The corners of the
stitching should be at the corners of the
frame. PLEASE NOTE: Overstretching the
fabric will result in uneven bunching of the
fabric. Pull the fabric just tight enough
to lay flat.
Connecting
Corners
Using the hand
tool
B
Connecting
middle cross
supports at
seams
D
C
A
A
C
D
2
3

Setup Instructions
STANDROID
Frame and Monitor
Connecting the Frame to the Base (E)
Attaching and Securing the Monitor
1. Slide assembled Frame and Fabric
(with graphic facing forward to the long
side of the base) onto protruding the
posts of the Base (E).
1. Before attaching your monitor (not included),
be sure the top 2 screw holes on the back are
15.75” (400mm) apart.
2. Determine the height you would like your
monitor to hang.
Please Note: The holes on the frame will
be at the same height as the screw holes on
the monitor.
3. Pull the fabric away from the frame at the
location of the desired screw hole and attach
the Monito Profile Bar (G) using the T-Bolt
and Wing Nut (H).
4. Attach the appropriate T-Bolts (I) into
the top screw holes on the monitor and
the correspondingly-sized Leveling Bolts (J)
into the lower screw holes.
Please Note: The extra sets of bolts are for
other mount patterns and will not be needed.
Please Note: Do not screw bolts in too far
as it can crack the screen. Most monitors
allow for at least 1/4” depth.
5. Attach the monitor by adjust a hook on one
side of the Monitor Profile Bar (G) so the ball
is outside the groove allowing the T-Bolts (I)
to slide into the groove. Once both bolts are
secured in the groove, re-adjust the hooks
so the ball is in the groove. This prevents the
monitor from sliding off.
6. Slowly tighten or loosen the Leveling Bolt for
Monitor (J) to adjust the angle of the monitor.
4
1
2
BACK OF SCREEN
Vertical Frame
BACK OF SCREEN
Mounting Holes
400mm (15.75”)
6” or less
A B

Setup Instructions
STANDROID
Frame and Hover Graphic
Securing the Leveling the Frame
Assembling and Mounting the Hover Graphic
1. Attach the Eye Nut with Wing Bolt (K)
through the hole in the center of the
top Horizontal Support (C).
2. Attach the Eye Bolt (L) to the base at the
screw hole insert located at the back.
3. Connect the Tension Wire (M) - First, the
the Carabiner to the top Eye Nut (K) and
then the Tension Screw to the Eye Bolt
(L) on the base.
4. Turn the middle of the tension screw until
the wire is tight and the display frame is
level.
1. Connect the tubing segments that are
bungee corded together. Each locking
push pin should snap in place.
2. The “T” shaped pieces slide into the two
holes located closest to the inside of the
frame.
3. Unzip the fabric graphic and slide over the
tubing frame so the graphic faces forward
(convex side).
4. Zip graphic closed around the outside
edge making sure that the “T” tubes
protrude through the holes on the back
(concave side) of the graphic.
5. Slide the angled tube supports onto the
ends of the “T” tubes protruding through
the graphic and tighten with wing nuts.
6. Slide the angled tube supports into the
plastic holes at the top of the frame.
1
1
5 6
4
3Assembled
Frame Profile
3