Oliso Mini project iron m2pro User manual

user manual

for model M2Pro

mini

project iron™

When using your iron, basic safety precautions should always be followed, including the following:

read all instructions before using this product

important safety instructions

special instructions

Use iron only for its intended use.

To protect against a risk of electric shock, do not immerse the iron in water or other liquids.

The iron should always be turned to “OFF” before plugging or unplugging from the outlet.

Never tug cord to disconnect from the outlet; instead, grasp plug and pull to disconnect

Do not allow cord to touch hot surfaces. Let iron cool completely before putting away.

Loop cord loosely around iron and/or solemate when storing.

Always disconnect iron from electrical outlet when ﬁlling with water or emptying and when not in use.

The iron is not to be used if it has been dropped, if there are visible signs of damage, or if it is leaking.

Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the

risk of electric shock, do not disassemble the iron. Take it to a qualiﬁed serviceperson for examination

and repair. Incorrect reassembly can cause a risk of electric shock when the iron is used.

Do not leave iron unattended while connected or on an ironing board.

This appliance is not intended for use by persons (including children) with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn

a steam iron upside down - there may be hot water in the reservoir. (*see illustration ––>)

If the iron is not operating normally, disconnect from the power supply and have the iron serviced by a qualiﬁed serviceperson.

Oliso® irons are high wattage appliances - Please switch your iron to your country’s voltage.

To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.

If an extension cord is absolutely necessary, a 10A cord should be used. Cords rated for less amperage may overheat.

Care should be taken to arrange the cord so that it cannot be pulled or tripped over.

This iron uses hot steam! Be sure to let iron cool before reﬁlling or storing.

Never direct ﬁll the iron from a water tap while the iron is plugged into a power source.

Soak up any excess water around iron (including power cord) before plugging back into an outlet.

FOR HOUSEHOLD USE ONLY.

This appliance was set at the factory to operate at 120 volts. Refer to the Operating Instructions section of this manual

for conversion to 220-240 volt operation.

Be sure dual voltage selector is in correct voltage position before operating. Before plugging in, read the information

about dual voltage operation contained in the instructions section of the manual.

7please save these instructions

When placing the iron on its solemate™, ensure that the surface on which the solemate™ is placed is stable.

When operating the iron, do not attempt to place vertically on its heel for resting. Use its solemate™

*correct hand

positioning

incorrect hand

positioning

(Burn warning)

Do not allow ﬁngers to

touch soleplate while hot.

solemate™

sight window

get to know your oliso®mini project iron®

side view top view solemate™

one-press

steam control

Dual Voltage

System

120V | 240V

351

detailer tip6

soleplate5

fabric selector

top ﬁll

water tank

4 simple steps to start

step 3

Plug in. Turn dial

clockwise to choose

desired fabric setting.

Note: light will pulsate

until temp is reached.

step 2

fill unplugged

Open the water tank lid

and add water to max

ﬁll line with cup or

directly from a faucet.

Note: ﬁll cup not included.

50mL equals max capacity.

step 4

iron

When the light stops

pulsating and is solid,

the iron is ready for use.

Note: rest iron on solemate™

when not in use.

set up

Max Fill

step 1

remove solemate™

Make sure to remove

the solemate™from the

iron’s soleplate before

turning on iron.

Max Fill

filling water tank

This iron is designed

to be used with

regular tap water.

If your water is

over 12 grams

of hardness, we

recommend using

either inexpensive

bottled spring water or

mixing half tap water

with half distilled water.

Alternatively, ﬁll directly from a

faucet holding the iron horizontally.

Make sure iron is unplugged.

If iron is over-ﬁlled wipe up excess water around

the iron before plugging the iron back in.

unplug ironswitch off open lid fill

50mL equals the max

capacity of the water tank.

Place the warm iron on the

solemate™ while it cools.

Then open lid.

Do not ﬁll the tank past the MAX

ﬁll line on the top of the iron.

Close the lid when done.

step 1 step 2 step 3

DO NOT

max fill line water

recommendations

alternative filling

Max Fill

(turn the dial

counter clockwise)

Note: ﬁll cup not included.

Max Fill

fabric selector

Turn the temperature + fabric

selector to desired setting.

settings temperature + fabric

low temp

medium temp

high temp

OFF

(synthetic)

(wool + silk)

(linen + cotton)

Note: to use steam burst,

the temperature must be

set to the (••, •••) range.

heating ready

solid

OFF

settings

OFF

status lightfabric selector

settings heating ready

pulsating

solid

OFF

steam button

status light

fabric selector dial

status light

steam button voltage

Note: if necessary, check that you are using an adapter

which meets the safety requirements of the country you are in.

This iron is set at the factory to operate at 120 volt.

Adjust the iron to correct

voltage for your location,

using a small ﬂat object

(ﬂat-head screwdriver).

place small ﬂat

object here

voltage settingsone-press burst of steam

110/120V 220/240V

IMPORTANT

Switching voltage

If set at 120V, the iron will

operate at 110 to 120V.

If set at 240V, the iron will

operate at 200 to 240V.

For a strong burst

of steam from

the soleplate.

press steam

buttons in

horizontal burst

The iron can only produce steam when the

fabric selector knob is set to (••, •••) range.

Fill with water (see page 5) and allow

the iron to heat up (solid light)

before pressing the steam button.

Press the burst of steam buttons and place the

iron a few inches away from the garment to

avoid damaging delicate fabrics.

120

solemate™

dual purpose solemate™

step 1 step 2

resting side

Lets the hot soleplate

safely rest every time

during ironing and

protects fabrics.

Pull down on tab at

back of solemate™

and remove

Insert front of soleplate

into front of solemate™ Wrap back tabs

around soleplate

attaching solemate™

remove solemate™

RESTING SIDE

side 1

RESTING SIDE

PATENT PENDING

STORAGE

SIDE

storage side

Easily snaps to the

soleplate for easy

transportation + storage.

side 2

PATENT PENDING

STORAGE

SIDE

back

Note:

allow soleplate to cool

thoroughly before attaching solemate

™

unplug iron let cool off wrapping cordswitch off

(turn the dial

counter

clockwise)

store iron properly

step 3step 2 step 4

For easy storage, the

power cord can be

wound loosely around

the iron once it has

cooled. Hook allows for

easy hanging storage.

step 1

Allow soleplate

to cool thoroughly,

then attach solemate™

(see page 8)

Iron should remain

unplugged when

not in use.

problem things to check solution

Iron does

not heat

Is fabric selector set to o?

Is iron plugged in correctly?

Turn the fabric selector knob to a fabric setting.

Check to make sure the plug is fully plugged into a working power outlet.

Also make sure that there are not other appliances which could overload the power outlet.

Iron

produces

little or

no steam

Is there enough water in the tank?

Check “sight window” on the side of the iron to see if there is water in the tank. If you don’t see water

in the tank you can also check by unplugging the iron & letting it cool. Place the iron on the resting

side of the solemate™ on a secure surface. Carefully open the lid on the top ﬁll water tank to check the

water level. Top o the water level as needed, not going over the max ﬁll on the plastic housing.

Is iron hot enough?

Are you pressing the steam buttons?

Did you let your iron rest?

The fabric selector must be set to (•• or •••) to produce steam. Wait until the lights on the

“one-press steam control” activate to let you know that the soleplate is warm enough to make

a good solid steam burst.

The iron can only produce steam when the fabric

selector knob is set to (••, •••) range.

If your iron has been on a long time (excess of half hour) without steam use, please let your

iron rest (unplugged) for about 5 to 10 minutes. This will allow steam to produce.

trouble shooting guide

maintenance + cleaning

Always clean the soleplate of a steam iron when it Is cool.

The soleplate should be cleaned if starch or other residue builds up. When the iron is cool, wipe the soleplate with a soft, damp cloth.

Or purchase commercially available soleplate cleaner and follow the instructions according to the manufacturer.

Do not use abrasive cleaners or scouring pads as this will damage the iron’s soleplate and its coating.

Mineral deposits from tap water can occur in the soleplate vents. To clean, ﬁll the water tank and heat the iron to the highest (•••) setting.

Once the iron is fully heated, unplug the iron and hold over a sink. Press the steam button repeatedly until water begins

to drip out of the soleplate. Be careful, as this creates large amounts of steam.

Do not use any heavy duty cleaning or descaling products, such as abrasive sponges.

Never hold iron under a running tap while plugged into the wall. Be sure the iron is cold before ﬁlling and if you spill water by overﬁlling,

be sure to dry o iron with a cloth before plugging the iron back into the outlet.

Be sure to rest iron on soft surface that will not burn, such as our solemate™, during

use and storage. Be careful of the iron's hot surface until it cools.

It is best to empty the water tank after you ﬁnish ironing. Let water cool before emptying.

Make sure the iron is cool before storing it.

Clean solemate™ by using water & soft dish soap. Let dry before installing onto iron. Solemate™ is dishwasher safe.

If any problem persists, contact our customer service

1-800-899-5157 or [email protected]

warranty

Oliso warrants that for a period of three years (mini project iron™) from the date of the original purchase, this product will be free from defects in material

and workmanship, when utilized for normal household use. Oliso will repair or replace this product or any component of the product found to be defective

during the warranty period without charge to the customer. If a replacement product is sent, it will carry the remaining warranty of the original product.

Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a

similar product of equal or greater value. This is your exclusive warranty.

This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of

purchase is required to obtain warranty performance. Oliso dealers or retail stores selling oliso products do not have the right to alter, modify or in any way

change the terms and conditions of this warranty.

The liability of oliso is limited solely to the cost of repair or replacement of the product at its option. This warranty does not cover normal wear of parts and

does not apply to any product that has been tampered with or used for commercial purposes. This warranty does not cover damage caused by misuse,

abuse, use on improper voltage or current, use contrary to the operating instructions, negligent handling or damage due to faulty packaging or mishandling

in transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alteration to the

product or any of its parts, which have been performed by a repair person not authorized by oliso. Further, the warranty does not cover Acts of God such

as ﬁre, ﬂood, hurricanes, and tornadoes.

This warranty is extended to the original purchaser of the product and excludes all other legal and/or conventional warranties. The responsibility of oliso is

limited to the speciﬁc obligations expressly assumed by it under the terms of the limited warranty. In no event shall oliso be liable for any incidental or

consequential damages caused by breach of any express, implied or statutory warranty or condition.

Except to the extent prohibited by law, any implied warranty or condition of merchantability or ﬁtness for a particular purchase is limited in duration to the

duration of the above warranty. oliso disclaims all other warranties, conditions, or representations, express, implied, statutory or otherwise. In no event shall

oliso be liable for any indirect, special, incidental or consequential losses or damages (including but not limited to interruption of business or loss of

business or proﬁt) resulting from the use of or inability to use the product, any breach of contract, fundamental or otherwise, or for any claim brought

against purchaser by any other party. Some states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or

limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. If you have any question regarding this

warranty or would like to obtain warranty service, please email oliso at customerservice@oliso.com, and a service center address will be provided to you.

8:30am - 4:30pm (Paciﬁc) Monday-Friday 1-800-899-5157