Oliver IGD TOCSIN 700+ Guide

Tel:
Fax:
Email:
Web Site:
[phone]
[phone]
[email protected]
www.oliver-igd.co.uk
I G D
O L I V E R
4a Pepper Road
Stockport
SK7 5BW
England
Oliver IGD Limited V9.0
TOCSIN 700+
INSTALLATION
AND
USER INSTRUCTIONS

Table of Contents
Specification
Overview
Interface Wiring
Operating System
3
3
7
8
9
10
11
12
13
14
15
17
18
21
22
23
26
27
29
30
34
36
38
40
44
45
46
47
48
49
50
51
CE Declarations
Relay Outputs, Audio Visual Output, two and
three wire detectors
3 Wire 4-20mA Pellistors (analogue)
Digital Port
Toxic Analogue Detectors 2 wire
Infra Red 3 Wire Detectors
FREON Detectors
Fire and Smoke Detector Inputs
Addressable Detectors
Addressable Relay Outputs
19" Rack System Versions
Accepting and Resetting Alarms
Basic Menu Operation
User Menu System Overview
Zero and Calibration Commands
Alarm Setup
Channel Description Edit
Engineers Menu Overview
Detector Channel Setup
FIND detectors command
Additional Relay Outputs
Analogue Outputs
Addressable Sensor Test
Addressable Relay Test
Fire Input Test
Production Menu Overview
Alarm Operation
Mimic Panels
RS 485 Repeaters
Modbus Map

OLIVER I G D
This product must be earthed in accordance with local safety regulations.
The Control Panel leaves the factory configured for the supply voltage stated on the customers order.
Standard voltage and frequency range is:-
AC Mains Powered 85 to 264 VAC 40 to 400 Hz
DC Low Voltage Powered 18 to 30V DC
Should the control panel be used in conjunction with portable generating equipment, care should be taken to ensure that
the electrical supply is within the tolerance band described above. The control panel may be stored at temperatures
0 0
between 0 C and 55 C. If stored at low temperatures and then brought into a warmer environment, condensation may
form on some components. In such a situation , this condensation should be allowed to evaporate prior to use of the
equipment. If stored at high temperature, care should be taken to ensure that humidity condensation does not enter
critical electrical components, for example the power supply. The Control Panel is designed to operate within
o o
specification for ambient temperature between 0 C and 55 C, relative humidity up to 95% ( non-condensing ).
!Warning !
Do not use a Control Panel for protection applications that has not been calibrated. If calibration seals are missing from
the control panel or have been tampered with or broken, then the control panel must be re-calibrated and sealed by a
trained engineer.
See declaration CE-700-03
Page 3 of 52
Power Source 85 to 264 VAC ( 18 to 30 VDC Option)
Power Consumption 60 Watts (basic) 150 Watts (700+)
Display 2 x 16 backlight LCD
Operating Temperature 0°c to 55°c
Operating Humidity Up to 95% non-condensing
Resolution 0.00% or ppm Range Dependant
Update Rate 1 Second
Size (mm) 255 (H) x 265 (W) x 100 (D)
Protection Standard IP54. With seal kit option fitted IP55
Inputs Up to 4 or up to 8 x 4-20mA loops
Additional 8 analogue 4-20mA loopsInputs (Optional)
2 x RS485 data highways for up to 64 detectors (700+)
3 x configurable SPCO relays (7 Amp non conductive load)
1 x fault SPCO relays (7 Amp non conductive load)
1 x solid state audio/sounder 24VDC
Outputs (Standard)
1 x solid state visual/flasher 24VDC
Outputs (Optional) Up To 32 x configurable SPCO relays 7 Amp non inductive load
Up To 16 x Analogue Outputs (4 per additional card)
Up To 32 x Addressable Relay Outputs
Optional Equipment Battery backup module 7AH 255 (H) x 265 (W) x 100 (D)
CE Declaration BS EN61000-6-4 EMC Compatibility 'Emissions'
Weight 4.6 KG
BS EN 61000-6-2:2001 EMC Compatibility 'Immunity'
BS EN 61010-1: 2001 Safety requirements, electrical equipment
Who should read this manual.
This manual is intended for use by trained installers of gas detection systems who are technically competent and
have all necessary tools to undertake installation and maintenance on this type of equipment.
Failure to install and maintain the equipment properly can render the detector ineffective.
You should not undertake any of the procedures in this manual if you do not have access to the correct equipment,
have not undertaken training on this or similar equipment or are not technically qualified to install this equipment.
Calibration gases and test equipment is available from IGD.

EC Declaration of Conformity
OLIVER I G D
CO
H2S
CO2
SO2
NO NO2
CH4
Issuers name and address:
Oliver IGD Limited of
4a Pepper Rd
Stockport, SK7 5BW
United Kingdom
Declares that the product listed as:
TOCSIN 700
Multi-Channel Hazardous Gas Detector Control Panel
IP54 Version.
Part Numbers 5109601 5109602 5109601DC
5110001 5110001DC 5110801
5110801DC
Are in conformity with the provisions of the following European Directive(s) when installed, operated, serviced
and maintained in accordance with the installation and operating instructions contained in the product
documentation.
And that the standards and/or technical specifications referenced below have been applied or considered.
2004/108/EC EMC Directive
2006/95/EC Low Voltage Equipment Directive (note not applicable to 24V DC Powered Versions)
EN 61779-1:2000
EN 50271:2001
BS EN 60529
Technical File Reference
Electrical apparatus for the detection and measurement of flammable gases,
general requirements and test methods.
Electrical apparatus for the detection and measurement of combustible gases,
toxic gases or Oxygen: requirements and tests for apparatus using software and
or digital technologies. Excluding requirements for SIL
Requirements for the classification of degrees of protection provided by
enclosures for electrical equipment.
T700-TF9
Product Markings
Issued on: 16 May 2011 At Oliver IGD Limited, Stockport, SK7 5BW , United Kingdom
Notified Body For ATEX and/or QAN:
Sira Test & Certification Ltd
Hazardous Area Centre,
Rake Lane
Eccleston, Chester, CH4 9JN.
United Kingdom
Oliver IGD Limited operate an independently assessed
ISO9001:2008 Quality Assurance System and ATEX QAN.
Quality Assurance Certificate Number
023827
Quality Assurance Notification Number
SIRA 02ATEX M174
Signature:
Name Andrew J Collier M.I.Mech I.E I.Eng M.I.O.D
Position: Managing Director
Date: 16 May 2010
Declaration Ref: T700IP54CE-2
Declaration of Conformity in accordance with EN ISO/IEC 17050-1:2004
Page 1 of 1
TOCSIN 700+
Serial Numbers: S/17588-1-1 & S/17588-1-2
Page 4 of 52

EC Declaration of Conformity
OLIVER I G D
CO
H2S
CO2
SO2
NO NO2
CH4
Issuers name and address:
Oliver IGD Limited of
4a Pepper Rd
Stockport, SK7 5BW
United Kingdom
Declares that the product listed as:
TOCSIN 700
Multi-Channel Hazardous Gas Detector Control Panel
IP66 Version.
Part Number 5110005 IP66
Are in conformity with the provisions of the following European Directive(s) when installed, operated, serviced
and maintained in accordance with the installation and operating instructions contained in the product
documentation.
And that the standards and/or technical specifications referenced below have been applied or considered.
2004/108/EC EMC Directive
2006/95/EC Low Voltage Equipment Directive (note not applicable to 24V DC Powered Versions)
EN 61779-1:2000
EN 50271:2001
BS EN 60529
Technical File Reference
Electrical apparatus for the detection and measurement of flammable gases,
general requirements and test methods.
Electrical apparatus for the detection and measurement of combustible gases,
toxic gases or Oxygen: requirements and tests for apparatus using software and
or digital technologies. Excluding requirements for SIL
Requirements for the classification of degrees of protection provided by
enclosures for electrical equipment.
T700-TF9
Product Markings
Issued on: 12 Jan 2009 At Oliver IGD Limited, Stockport, SK7 5BW , United Kingdom
Notified Body For ATEX and/or QAN:
Sira Test & Certification Ltd
Hazardous Area Centre,
Rake Lane
Eccleston, Chester, CH4 9JN.
United Kingdom
Oliver IGD Limited operate an independently assessed
ISO9001:2008 Quality Assurance System and ATEX QAN.
Quality Assurance Certificate Number
023827
Quality Assurance Notification Number
SIRA 02ATEX M174
Signature:
Name Andrew J Collier M.I.Mech I.E I.Eng M.I.O.D
Position: Managing Director
Date: 12 Jan 2009
Declaration Ref: T700IP66CE-2
Declaration of Conformity in accordance with EN ISO/IEC 17050-1:2004
Page 1 of 1
TOCSIN 700 or TOCSIN 700+
S/-serial number
Page 5 of 52

EC Declaration of Conformity
OLIVER I G D
CO
H2S
CO2
SO2
NO NO2
CH4
Issuers name and address:
Oliver IGD Limited of
4a Pepper Rd
Stockport, SK7 5BW
United Kingdom
Declares that the product listed as:
TOCSIN 700
Multi-Channel Hazardous Gas Detector Control Panel
IP55 Version with seal kit fitted.
Part Numbers 5109601 5109602 5109601DC
5110001 5110001DC 5110801
5110801DC
Are in conformity with the provisions of the following European Directive(s) when installed, operated, serviced
and maintained in accordance with the installation and operating instructions contained in the product
documentation.
And that the standards and/or technical specifications referenced below have been applied or considered.
2004/108/EC EMC Directive
2006/95/EC Low Voltage Equipment Directive (note not applicable to 24V DC Powered Versions)
EN 61779-1:2000
EN 50271:2001
BS EN 60529
Technical File Reference
Electrical apparatus for the detection and measurement of flammable gases,
general requirements and test methods.
Electrical apparatus for the detection and measurement of combustible gases,
toxic gases or Oxygen: requirements and tests for apparatus using software and
or digital technologies. Excluding requirements for SIL
Requirements for the classification of degrees of protection provided by
enclosures for electrical equipment.
T700-TF9
Product Markings
Issued on: 16 Feb 2009 At Oliver IGD Limited, Stockport, SK7 5BW , United Kingdom
Notified Body For ATEX and/or QAN:
Sira Test & Certification Ltd
Hazardous Area Centre,
Rake Lane
Eccleston, Chester, CH4 9JN.
United Kingdom
Oliver IGD Limited operate an independently assessed
ISO9001:2008 Quality Assurance System and ATEX QAN.
Quality Assurance Certificate Number
023827
Quality Assurance Notification Number
SIRA 02ATEX M174
Signature:
Name Andrew J Collier M.I.Mech I.E I.Eng M.I.O.D
Position: Managing Director
Date: 16 Feb 2009
Declaration Ref: T700IP55CE-2
Declaration of Conformity in accordance with EN ISO/IEC 17050-1:2004
Page 1 of 1
TOCSIN 700+
Serial Number
Page 6 of 52

OLIVER I G D
Tocsin 700 Panel Overview
2 x 16 LCD Display
24V DC Panel Power
Digital Inputs
Jog Wheel
3 off Configurable Relay Outputs
With Activation Indication Lamps
Sounder/Flasher
Outputs
Fault Relay Outputs
RS 485 Detector
Data Highway
Connector Port 1
‘C1’
(Addressable Versions)
RS 485 Detector
Data Highway
Connector Port 2
‘C2’
(Addressable Versions)
Expansion
Connector
8 off 4-20mA Loop Inputs
Mains/DC Input
(Check Supply Option Before Use) Grounding Points
L N E 110/230V AC 50/60Hz
RS232 Comm
Port
Page 7 of 52

OLIVER I G D
Tocsin 700 Interface wiring
Sounder Alarm
Max Current
150mA 24V DC
These 3 relays can be assigned,
named, zoned etc using the Tocsin
700 operating software.
Dedicated fault relay output, this output
is energised in normal operation
In all Cases:
Relay contact ratings.
7A @ 250V AC Non-Inductive
7A @ 30V DC Non-Inductive
Spike suppression must be fitted
Note that FAULT relays are normally
energised on power up.
Addressable control panel versions only.
See 'Addressable Sensors' Section
24V DC
24V DCAUDIO
OUTPUT
VISUAL
OUTPUT
SOUNDER O/P
WARNING LAMP O/P
Enclosure
Ground
Enclosure
Ground
1.5mmSQ See Panel
for recommended cable
types. Typical max cable
run 1000M.
1.5mmSQ See Panel
for recommended cable
types. Typical max cable
run 1000M.
Blue
Red
Black
Red
Blue
TOCSIN 102/A
TOXIC GAS
DETECTORS
TOCSIN 102IR
FLAMMABLE GAS/
CO2 DETECTORS
+24V DC
B
A
0V
Note Flasher on
with alarm level 1.
Buzzer on with
alarm level 2.
NO NC
COM
AL1
AL2
AL3
0V DC
4-20mA IN
+24V DC
GND
GND
Page 8 of 52

OLIVER I G D OLIVER I G D
Tocsin 700 Interface wiring...continued
T106P Pellistor
Flammable Gas
Detectors
1.5mmSQ See Panel
for recommended cable
types.Max cable
run 1000M.
0V DC
4-20mA IN
+24V DC
GND
ZERO
FAULT
CAL 360
CHASS
24V DC
B
A
GND
mA
P Y W
Common Active Compensator
mA+360CONC0V mA-
Page 9 of 52

OLIVER I G D OLIVER I G D
Tocsin 700 Interface wiring...Digital Port
Located at the top edge of the Tocsin
700 card is a 4 way connector used to
allow digital interface to the Tocsin 700
operating system as follows:
0V common
Password Inhibit
Reset Alarms
Inhibit Alarms
1 2 3 4
Page 10 of 52

0V DC
4-20mA IN
+24V DC
GND
OLIVER I G D OLIVER I G D
Tocsin 700 Interface wiring...continued
Tocsin 700 to Tocsin 103 2 wire Detector Series
Enclosure
Ground
4-20mA Toxic
And Oxygen Gas
Detectors
1.5mmSQ See Panel
for recommended cable
types. Typical max cable
run 500M.
24V DC
SCREEN
4-20mA
Page 11 of 52

0V DC
4-20mA IN
+24V DC
GND
OLIVER I G D OLIVER I G D
Tocsin 700 Interface wiring...continued
Tocsin 700 to Tocsin 103 3 wire Detector Series
Enclosure
Ground
4-20mA Flammable
And CO2 Gas
Detectors
Cable Guidance Panel
It is imperative to use cabling which suits
the environment in which the T700 and its
sensors are to be used. The following is intended
as a guide.
Fit 1.5mm SQ cable for analogue systems
Fit 2.5mm SQ cable for addressable systems
Use
Pirelli LSX type cable for office/light commercial
un-zoned installations
Steel Wire Armored or CY cable for medium/heavy
industrial un-zoned installations
Mineral Insulated Pyro cable for all hazardous
area zoned installations.
Note in all cases the T700 Panel must be installed outside
of any hazardous area and must be supplied via
a fused spur.
1.5mmSQ See Panel
for recommended cable
types. Max cable
run 1000M.
Screen
0V DC
24V DC
4-20mA
GND
Page 12 of 52

OLIVER I G D OLIVER I G D
Tocsin 700 Interface wiring...continued
Enclosure
Ground
T103 FREON Gas
Detectors
DIP Switches For Relay O/P
And Sounder O/P Enable
Sensitivity Adjustment
Factory Preset
Do Not Adjust
1.5mmSQ See Panel
for recommended cable
types. Typical max cable
run 500M.
0V DC
24V DC
4-20 OUT
NO
COM
NC
0V DC
4-20mA IN
+24V DC
GND
Page 13 of 52

OLIVER I G D OLIVER I G D
Tocsin 700 Interface wiring...continued
4-20mA IN
+24V DC
GND
INTERFACING TO FIRE AND SMOKE DETECTOR
DIODE BASES.
NOTE IF SUPPLIED IN THIS FORMAT THE INPUT
CONNECTORS INCORPORATE PROTECTION
DIODE. DO NOT USE WITHOUT THIS
CONNECTOR/DIODE
ASSEMBLY
NOTE LAST DEVICE IN LINE TO BE FITTED WITH
5K6 RESISTOR AS INDICATED
FIRE AND SMOKE INPUTS (FACTORY OPTION)
NOTE THESE DETECTORS ARE RESET BY
INTERRUPTION OF THE POWER SUPPLY. THE
TOCSIN 700 WILL DO THIS IF THE CHANNEL IS
SELECTED AS A ‘FIRE’ AS A GAS TYPE, RELAY
OUTPUTS MUST BE SET AS LATCHING. NOTE
THAT THE POWER IS SUPPLIED TO THE INPUT
CONNECTORS IN BANKS OF FOUR. IF MIXING
WITH GAS DETECTORS SEGREGATE THE FIRST
FOUR INPUTS AS GAS DETECTORS AND THE
SECOND FOUR INPUTS AS SMOKE DETECTORS.
THIS IS A FACTORY FIT OPTION AND MUST BE
REQUESTED WHEN ORDERING THE CONTROL
PANEL. CHANNEL HARDWARE CONFIGURATION
IS DIFFERENT TO STANDARD 4-20mA INPUTS
3
1
6
5
4SD DIODE BASE
3
1
6
5
4SD DIODE BASE
3
1
6
5
4SD DIODE BASE
NOTE: TYPE INDICATED IS TYPICAL OF NITTAN ST-I
CONVENTIONAL OPTICAL SMOKE OR HEAT DETECTORS. OTHER
MANUFACTURER CONNECTIONS MAY VARY.
Page 14 of 52

OLIVER I G D OLIVER I G D
Tocsin 700 Interface wiring...continued, Addressable Systems.
120 Ohm Termination
Resistor on the Last
Detector in Line
2.5mm SQ Cable See Previous Note
Use Junction Boxes Suitable for Area Classification
24V
SCREEN SCREEN
Rx
24V 24V
Tx 4-20
B B
A A
0V
0V 0V
Tocsin 102 Addressable
Series Detector Head
Red White Yellow Blue
Black
Local Comms
Connector For
Palm Connection
24V
SCREEN SCREEN
Rx
24V 24V
Tx 4-20
B B
A A
0V
0V 0V
Tocsin 102 Addressable
Series Detector Head
Red White Yellow Blue
Black
Local Comms
Connector For
Palm Connection
+24V DC
B
A
GND
GND
Page 15 of 52

OLIVER I G D OLIVER I G D
Tocsin 700 Interface wiring...continued, Addressable Systems Cont.....
2.5mm SQ Cable See Previous Note
Use Junction Boxes Suitable for Area Classification
+24V DC
B
A
GND
GND
ZERO
FAULT
CAL 360
CHASS
24V DC
B
A
GND
mA
P Y W
Common Active Compensator
ZERO
FAULT
CAL 360
CHASS
24V DC
B
A
GND
mA
P Y W
Common Active Compensator
ZERO
FAULT
CAL 360
CHASS
24V DC
B
A
GND
mA
P Y W
mA+360CONC0V mA-
Common Active Compensator
mA+360CONC0V mA- mA+360CONC0V mA-
Page 16 of 52

OLIVER I G D OLIVER I G D
Tocsin 700 Interface wiring...continued, Addressable Systems Cont.....
2.5mm SQ Cable See Previous Note
Use Junction Boxes Suitable for Area Classification
+24V DC
B
A
GND
GND
CHASS PALM
Set Address
24V DC
B
A
GND
mA
4300
PWR M EN Al COMM
CHASS PALM
Set Address
MUTE ALARM MUTE ALARM
24V DC
B
A
GND
mA
4301
PWR M EN Al COMM
Addressable Relay Outputs
These come equipped with two volt
free contacts which can be set as
normally open or normally closed action
Use for beacon/sounders etc
Mix on the same loop as addressable detectors
Page 17 of 52

483.0
External Addressable Relay Card
Alarm Sounder
Jog Wheel
133.4
240.0
7 0 0
ADVA NCED G A S DET E C T ION S YSTE M
RS485 to HUB
RS485 to HOST
or HMI PANEL
Connection to Addressable Gas
Detectors and Addressable Relays
Power and Modbus Connection
Detector Connector:
Pin 1 24V DC
Pin 2 Comm B
Pin 3 Comm A
Pin 4 0V DC
Power Connector: Cable
Pin 1 Comm B Grey
Pin 2 Comm A Green/Yellow
Pin 3 24 V DC Brown
Pin 4 0V DC Black
19" Rack Mount systems
OLIVER I G D OLIVER I G D
4208 4209 4210 4211
4212 4213 4214 4215 4216
Optional Event Panel Printer
Optional Keyswitch
Tocsin 700R 19" rack versions of the control panel are 24V DC powered and only interface as addressable
systems. The systems are shipped with an addressable relay card mounted to the rear which can be remote
mounted if required. Note that detectors are connected via the relay card connector shown below.
Addressable Gas Detectors and Addressable interface modules connect here
in the same manner described previously.
ZERO
FAULT
CAL 360
CHASS
24V DC
B
A
GND
mA
P Y W
Common Active Compensator
ZERO
FAULT
CAL 360
CHASS
24V DC
B
A
GND
mA
P Y W
mA+360CONC0V mA-
Common Active Compensator
mA+360CONC0V mA-
4101 41024102
Tocsin 106 Pellistor Flamable
Gas Detectors Shown
Page 18 of 52

Addressable Relay Card
Highways Connection
Pin 1 0V DC
Pin 2 Comm A
Pin 3 Comm B
Pin 4 24 V DC
Pin 1 0V DC
Pin 2 Comm A
Pin 3 Comm B
Pin 4 24 V DC
Highways Connection
Normally Closed
Common
Normally Open
Relay Terminals
Relay status LED,
ON when Energised
24V DC
0V DC
Power out for
use in
conjunction
with relays
First Relay on
The Card (relays
number from
this one).
Base Address set up
LED's and interface
for the relay card
In all Cases:
Relay contact ratings.
7A @ 250V AC Non-Inductive
7A @ 30V DC Non-Inductive
Spike suppression must be fitted
Note that FAULT relays are normally
energised on power up.
0V DC
24V DC
~~
A1
A1
A2
A2
Example fit
protection
diodes when
switching
external DC
loads.
Example fit protection
supressors when
switching external AC
loads typical device
Farnell Ref 1438460
OLIVER I G D OLIVER I G D
Page 19 of 52

OLIVER I G D OLIVER I G D
Operating System
Operating System Overview
2 Line x 16 Character LCD Display
Output Relay 1 Lamp
Output Relay 2 Lamp
Output Relay 3 Lamp
System Fault Lamp
Power On
Jog Wheel Rotate the jog wheel to move
up and down the system
menus.
Press the jog wheel to make
a selection or to accept/silence
an alarm
The Tocsin 700 series gas detector control panels are designed to be as flexible in operation as
possible. The system software allows the owner/installer to configure the following functions:-
Configure input type, not only the selection of pre-programmed input gases but also the option
to define an input type and scale the incoming 4-20mA signal to match. For example,
pressure, temperature, distance etc
Decide alarm levels for each input and decide, rising,falling or latching alarms and which relay
to asign to which inputs to allow, zoning etc
Logical naming of inputs, for example 'boiler 1' (max 8 characters)
Set the display scan rate
Zero and calibrate each channel from the control panel.
In addition the Tocsin 700 control panel can be 'hooked up' to a PC or PALM device via its serial
programming link to allow system configuration using Oliver IGD software. This allows not only pre-
configuration of the panel prior to commissioning but also a record of how the system was set up.
+Always refer to the shipping manifest and test schedule for confirmation of the shipped
configuration.
Page 20 of 52