Olivetti d-Copia 1801MF Plus User manual

d-Copia 1801MF
d-Copia 2201MF
d-Copia 1801MF Plus
d-Copia 2201MF Plus
DP-480/PF-480/DU-480
SERVICE
MANUAL
Published in November 2013
842NN112
2NNSM062
Rev.2

CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BAT-
TERIES ACCORDING TO THE INSTRUCTIONS.
It may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste
officials for details in your area for proper disposal.
ATTENTION
IL Y A UN RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACEE PAR UN MODELE DE TYPE
INCORRECT. METTRE AU REBUT LES BATTERIES UTILISEES SELON LES INSTRUCTIONS DONNEES.
Il peut être illégal de jeter les batteries dans des eaux d’égout municipales. Vérifiez avec les fonctionnaires
municipaux de votre région pour les détails concernant des déchets solides et une mise au rebut appropriée.
Notation of products in the manual
For the purpose of this service manual, products are identified by print speed at A4.
d-Copia1801MF/1801MF Plus: 18 ppm model
d-Copia2201MF/2201MF Plus: 22 ppm model
Or products are identified by correspondence of FAX.
d-Copia1801MF/2201MF: Basic model
d-Copia1801MF/2201MF Plus: Advanced model

Revision history
Revision Date Pages Revised contents
1 9 September 2013 Contents Change: Page number of the contents
1-2-20
1-2-26
1-5-24
1-5-64
1-5-76
Correction: Number of the screws
1-5-27 Clerical error correction: Deleted procedure 1
1-5-29 Correction: Number of the screws
Deleted: The detaching procedure of the drum unit
1-5-33 Added: Cautions sentence of the refitting
1-5-49 Added: Procedure 7 (Performs U167)
2-1-3, 2-1-4
2-2-24, 2-3-8
2-2-8, 2-3-9
Clerical error correction: Deleted the main power switch
(MSW) and the CN5 on power source PWB
Correction: YC20 (Right cover sw (reserve))
2 11 November
2013
Cover Added: Notation of products in the manual
Contents Change: Page number of the contents
Contents
(1-3-19 to 24)
Deleted: (2)Installing the key counter (option)
1-1-2, 1-1-12
1-2-9
Deleted: The statement of an option
1-1-2 Added: Interface for Advanced model
Change: Dimension and Weight
1-1-2, 1-1-12 Added: Option(Fax system and Network interface)
1-1-3 Clerical error correction of the item :
"First Copy" was changed to "First Print".
Added: to the description of “First Print Time”
1-1-5 Change: Dimensions of Paper Feeder (PF-480)
1-1-7 Added: 28 and 29
1-1-9, 1-1-10 Added: Operation panel for Advanced model
1-2-3, 1-2-4
1-2-5
Change: Change the form of the packing material
1-2-9 Change: A paper is changed into double fold.
1-2-16, 1-2-17 Added: The cautions sentence about High Altitude
1-3-4, 1-3-59 Added: U223 Lock Panel Ope (Advanced model only)
1-3-5 to 7,
1-3-81 to 100
Added: U600 to U699 for fax
1-3-9 Change: (4) and (5)
1-3-10 Added: "Advanced model only" to (2)
1-3-13 Added: (6) Option language version
Change: Item numbers
1-3-14 Added: "Advanced model only" to (2)
: (6) Option language version
Change: Item numbers

2 11 November
2013
1-3-15 Change: Item numbers
1-3-24, 1-3-25 Change: Data digit number of [LSU Out Top] and [LSU
Out Left]
1-3-25 to 40
1-3-42
1-3-44 to 46
1-3-51 to 53
1-3-55, 1-3-63
1-3-67, 1-3-68
1-3-70
1-3-72 to 1-3-74
1-3-78 to 80
1-3-116
1-3-117, 2-3-7
Correct: added the statement of a numerical change key
1-3-37 Correction: Description of "Back Head"
1-3-42, 1-3-43 Change: Items and Initial setting of Display
1-3-44 Added: The cautions sentence about High Altitude
Correction: The contents of Display and Description
1-3-51 Correction: Procedure 2 to 4 in U140
1-3-53 Correction: Setting range value in U156
1-3-54 Correction: delete the clearing function of U158
1-3-55 Correction: Setting range value in U161
1-3-57 Clerical error correction: The display of U199 is cor-
rected.
1-3-68 Correction: Setting range value in U332
1-3-69 Added: Procedure of setting to On/Off in U341
1-3-72 to 74 Correction: Setting range value in U402 ,U403 and U404
1-3-75 Deleted: Procedure 4 “Select [Target] and ..."
1-3-112
1-3-113
Deleted: How to display the history of paper jams
1-3-116 Deleted: U928 Life Cnt
1-4-3 Clerical error correction: Code 0120, 0121
1-4-94 to 109 Added: 1-4-9 Send error code
1-4-10 Error codes
1-5-19 Clerical error correction: Change the procedure 9 and
delete the procedure 10 and Figure 1-5-30
1-5-50 Added: Detaching and refitting the exit unit
2-2-2 Added: Master file name for Advanced model
Correction: Performance number in procedure 10
2-2-8 to 10
2-3-10
Added: YC2003, YC2007
2-3-8
2-3-10
Change: Signal name of YC8
Change: Signal name of YC1, YC2010, YC2011 and CIS
2-3-11 Change: Signal name of YC2, YC3 and YC4
Revision Date Pages Revised contents

2 11 November
2013
2-3-12 Change: Signal name of YC1, YC2 and YC6
Installation
guide
Added: IB-33 and FAX System(X)
Address Change: Address on New Zealand
Revision Date Pages Revised contents

This page is intentionally left blank.

Safety precautions
This booklet provides safety warnings and precautions for our service personnel to ensure the safety of
their customers, their machines as well as themselves during maintenance activities. Service personnel
are advised to read this booklet carefully to familiarize themselves with the warnings and precautions
described here before engaging in maintenance activities.

Safety warnings and precautions
Various symbols are used to protect our service personnel and customers from physical danger and
to prevent damage to their property. These symbols are described below:
DANGER: High risk of serious bodily injury or death may result from insufficient attention to or incorrect
compliance with warning messages using this symbol.
WARNING: Serious bodily injury or death may result from insufficient attention to or incorrect compliance
with warning messages using this symbol.
CAUTION: Bodily injury or damage to property may result from insufficient attention to or incorrect com-
pliance with warning messages using this symbol.
Symbols
The triangle ( ) symbol indicates a warning including danger and caution. The specific point of attention is
shown inside the symbol.
General warning. Warning of risk of electric shock.
Warning of high temperature.
indicates a prohibited action. The specific prohibition is shown inside the symbol.
General prohibited action. Disassembly prohibited.
indicates that action is required. The specific action required is shown inside the symbol.
General action required. Remove the power plug from the wall outlet.
Always ground the copier.

1. Installation Precautions
WARNING
• Do not use a power supply with a voltage other than that specified. Avoid multiple connections to
one outlet: they may cause fire or electric shock. When using an extension cable, always check that
it is adequate for the rated current. .....................................................................................................
• Connect the ground wire to a suitable grounding point. Not grounding the copier may cause fire or
electric shock. Connecting the earth wire to an object not approved for the purpose may cause
explosion or electric shock. Never connect the ground cable to any of the following: gas pipes, light-
ning rods, ground cables for telephone lines and water pipes or faucets not approved by the proper
authorities. ..........................................................................................................................................
CAUTION:
• Do not place the copier on an infirm or angled surface: the copier may tip over, causing injury. .........
• Do not install the copier in a humid or dusty place. This may cause fire or electric shock. .................
• Do not install the copier near a radiator, heater, other heat source or near flammable material. This
may cause fire. ...................................................................................................................................
• Allow sufficient space around the copier to allow the ventilation grills to keep the machine as cool
as possible. Insufficient ventilation may cause heat buildup and poor copying performance. ............
• Always handle the machine by the correct locations when moving it. .................................................
• Always use anti-toppling and locking devices on copiers so equipped. Failure to do this may cause
the copier to move unexpectedly or topple, leading to injury. ..............................................................
• Avoid inhaling toner or developer excessively. Protect the eyes. If toner or developer is accidentally
ingested, drink a lot of water to dilute it in the stomach and obtain medical attention immediately.
If it gets into the eyes, rinse immediately with copious amounts of water and obtain medical atten-
tion. .....................................................................................................................................................
• Advice customers that they must always follow the safety warnings and precautions in the copier’s
instruction handbook. .........................................................................................................................

2. Precautions for Maintenance
WARNING
• Always remove the power plug from the wall outlet before starting machine disassembly. ................
• Always follow the procedures for maintenance described in the service manual and other related
brochures. ..........................................................................................................................................
• Under no circumstances attempt to bypass or disable safety features including safety mechanisms
and protective circuits. ........................................................................................................................
• Always use parts having the correct specifications. ............................................................................
• Always use the thermostat or thermal fuse specified in the service manual or other related brochure
when replacing them. Using a piece of wire, for example, could lead to fire or other serious acci-
dent. ...................................................................................................................................................
• When the service manual or other serious brochure specifies a distance or gap for installation of a
part, always use the correct scale and measure carefully. ..................................................................
• Always check that the copier is correctly connected to an outlet with a ground connection. ...............
• Check that the power cable covering is free of damage. Check that the power plug is dust-free. If it
is dirty, clean it to remove the risk of fire or electric shock. .................................................................
• Never attempt to disassemble the optical unit in machines using lasers. Leaking laser light may
damage eyesight. ...............................................................................................................................
• Handle the charger sections with care. They are charged to high potentials and may cause electric
shock if handled improperly. ...............................................................................................................
CAUTION
• Wear safe clothing. If wearing loose clothing or accessories such as ties, make sure they are safely
secured so they will not be caught in rotating sections. ......................................................................
• Use utmost caution when working on a powered machine. Keep away from chains and belts. ..........
• Handle the fixing section with care to avoid burns as it can be extremely hot. ..................................
• Check that the fixing unit thermistor, heat and press rollers are clean. Dirt on them can cause
abnormally high temperatures. ...........................................................................................................