Olympia L-6160 User manual

INSTALLATION
Tools:
Adjustable Wrench Plumbers Putty Sealant Tape Rags
Model Number: L-6160,L-6170,L-6180,L-6161
L-6171,L-6181,L-6162,L-6172,L-6182
Warnings and Notes:
Check with local plumbing code requirements before installation.
This product should be installed by a local listed plumber.
Do not use plumbers putty on threads.
OLYMPIA FAUCETS, INC.
Interchange City Distribution Center #20
1277 Heil Quaker Boulevard
La Vergne, TN 37086
[phone]
www.olympiafaucets.com
Installation Steps:
Single Handle Lavatory Faucet
(1) Shut off water supplies. Remove old faucet.
Clean mounting surface in preparation for new
faucet.
(2) Place the faucet in position on the sink.
Apply plumbers putty under the base gasket.
Place washer and tighten with locknut.
(3a) When using ball-nose exible supplies
to connect faucet to water supply lines,
slip coupling nut onto exible supply. Ball-
nose coupling will go partially into shank.
Tighten coupling nut (DO NOT OVER
TIGHTEN). Install opposite end according to
manufacturer’s instruction for both tubes.
(3b) When using stainless steel braided
faucet supply hose, this faucet requires one
end of the supply hose to have a 1/2” female
IPS connection. The other end of this supply
hose must match the thread on the water
supply valve under your sink. Once you’ve
identied the required size, carefully follow
the manufacturer’s installation instructions for
each hose.
(4) Important: After installation is complete,
remove aerator. Turn water supply on and
allow both hot and cold water to run at least
one minute each. While water is running,
check for leaks. Turn off water and replace
aerator.
(1) Remove pop-up ange from body
(2) Place a ring of putty on the bottom of
ange.
(3) Insert pop-up ange through drain hole
and attach ange to body. Ensure the pop-up
outlet faces towards the back of the sink.
Tighten the locknut securely with a wrench.
Do not overtighten.
Pop-up Drain Installation:
(5) Remove pivot rod nut from pop-up body,
ensure the washers is in place, insert pivot
rod, tighten pivot rod nut back to pop-up body.
(4) Remove the excess putty. Connect the
trap (check manufacturer’s instructions for
installation).

Exploded Drawing:
* Note: Please specify nish/color when ordering. ITEM # DESCRIPTION
A1 OP-190001* Metal Lever Handle
A2 OP-190002* Metal Loop Handle
A3 OP-190008 Acrylic Ball Handle
A4 OP-490023 Acrylic Handle Adapter
B OP-490003* Cap & Adjusting Ring
C OP-490004 Cam & Washer
D OP-390001 Stainless Steel Ball
E OP-490041 Springs & Seats
F OP-490035* 1.5 GPM Aerator
G OP-530001 Mounting Kit
H OP-590001 Supply Nut
I OP-630004*
OP-630002*
50/50 Pop-Up Drain Assembly
Brass Pop-Up Drain Assembly
1 OP-490002 Hot & Cold Indicator
2 OP-490043 Allen Screw
3 OP-490021 Acrylic Ball Handle Button
4 OP-490022 Acrylic Ball Handle Screw
For more care information or trouble shooting
inquiries about your Olympia product, Please call:
OLYMPIA FAUCETS, INC. [phone]
8AM - 8PM EST (5AM to 5PM PST)
www.olympiafaucets.com
(6) Push pivot rod down, insert drain plug
carefully. Test to ensure drain plug works
properly.
(7) Connect lift rod strap to pivot rod by using
clip. Tighten the thumbscrew to connect lift rod
strap to pop-up lift rod.