Olympia L-7240 User manual

INSTALLATION
Tools:
Adjustable Wrench Plumbers Putty Sealant Tape Rags
Model Number: L-7240,L-7241,L-7242,L-7270
L-7271,L-7272 (CP, PVD BN, ORB)
Warnings and Notes:
Check with local plumbing code requirements before installation.
This product should be installed by a local listed plumber.
Do not use plumbers putty on threads.
OLYMPIA FAUCETS, INC.
Interchange City Distribution Center #20
1277 Heil Quaker Boulevard
La Vergne, TN 37086
[phone]
www.olympiafaucets.com
Installation Steps:
Two Handle Lavatory Faucet
(1) Shut off water supplies. Remove old faucet.
Clean mounting surface in preparation for new
faucet.
(2) Place the faucet in position on the sink.
Apply plumbers putty under the base gasket.
Install washer on shanks and tighten with
locknut.
(3a) When using ball-nose exible supplies
to connect faucet to water supplylines, slip
coupling nut onto exible supply. Ball-nose
coupling will go partially into shank. Tighten
coupling nut (DO NOT OVER TIGHTEN). In-
stall opposite end according to manufacturer’s
instructions for both tubes..
(3b) When using stainless steel braided
faucet supply hose, this faucet requires one
end of the supply hose to have a 1/2” female
IPS connection. The other end of this supply
hose must match the thread on the water
supply valve under your sink. Once you’ve
identied the required size, carefully follow
the manufacturer’s installation instructions for
each hose.
(4) Turn on water supplies. Check for any
minor joint leaks. Remove aerator from spout
by turning counterclockwise. Turn on both side
handles. Flush and allow water to run at full
ow at least one minute. Turn off both side
handles. Replace aerator.
(1) Remove pop-up ange from body
(2) Place a ring of putty on the bottom of
ange.
(3) Insert pop-up ange through drain hole
and attach ange to body. Ensure the pop-up
outlet faces towards the back of the sink.
Tighten the locknut securely with a wrench.
Do not overtighten.
Pop-up Drain Installation:
(4) Remove the excess putty. Connect the
trap (check manufacturer’s instructions for
installation).
(5) Remove pivot rod nut from pop-up body,
ensure the washers is in place, insert pivot
rod, tighten pivot rod nut back to pop-up body.

Exploded Drawing:
* Note: Please specify nish/color when ordering. ITEM # DESCRIPTION
A1 OP-190010C,H* Lever Handle Cold, Hot (For L-724X)
A2 OP-190015C,H* Lever Handle Cold, Hot (For L-727X)
B OP-490040 Bonnet Nut
C OP-390004 Cartridge-Brass Post
D OP-490041 Springs & Seat
E OP-590003 Mounting Locknut & Washer
F OP-590001 Supply Nut
G OP-430007 1.5 GPM Aerator
H OP-630004*
OP-630002*
50/50 Pop-Up Drain Assembly
Brass Pop-Up Drain Assembly
I OP-430005 Hole Cover (For L-7241,L-7271)
1 OP-490029 3/32” Allen Screw
For more care information or trouble shooting
inquiries about your Olympia product, Please call:
OLYMPIA FAUCETS, INC. [phone]
8AM - 8PM EST (5AM to 5PM PST)
www.olympiafaucets.com
(6) Push pivot rod down, insert drain plug
carefully. Test to ensure drain plug works
properly.
(7) Connect lift rod strap to pivot rod by using
clip. Tighten the thumbscrew to connect lift rod
strap to pop-up lift rod.