Omcan FR-CN-0005 User manual

Revised - 09/08/2023
Toll Free: 1-800-465-0234
Fax: [phone]
Email: [email protected]
www.omcan.com
Refrigerated Showcases
Models FR-CN-0005, 0009, 0014
Items 47742, 47743, 47744
Instruction Manual

2
Page
-------------------------------------------------------------------------------------------- 3
--------------------------------------------------------------------------- 4 - 5
--------------------------------------------------------------------------- 5 - 6
-------------------------------------------------------------------------- 7
-------------------------------------------------------------------------------------------- 8
--------------------------------------------------------------------------------------------- 8
----------------------------------------------------------------------------------------- 9
------------------------------------------------------------------------------- 9 - 10
---------------------------------------------------------------------------- 11 - 16
---------------------------------------------------------------------- 17 - 18
---------------------------------------------------------------------------- 19
Table of Contents
Section
Disclaimer
General Information
Safety and Warranty
Technical Specications
Installation
Operation
Maintenance
Troubleshooting
Parts Breakdown
Electrical Schematics
Warranty Registration
Model FR-CN-0005 / Model FR-CN-0009 / Model FR-CN-0014

3
Disclaimer
OMCAN IS NOT RESPONSIBLE FOR ANY DAMAGES
DUE TO WATER LEAKS. WARRANTY FOR
WATER LEAKS IS VOID IF THE AMBIENT ROOM
TEMPERATURE EXCEEDS 75°F AND 55% RELATIVE
HUMIDITY, AND THE APPLIANCE DRAIN IS NOT
CONNECTED DIRECTLY TO A FLOOR DRAIN.
OMCAN NO SE HACE RESPONSABLE DE LOS
DAÑOS CAUSADOS POR FUGAS DE AGUA. LA
GARANTÍA POR FUGAS DE AGUA QUEDA ANULADA
SI LA TEMPERATURA AMBIENTE SUPERA LOS 75°F Y
EL 55% DE HUMEDAD RELATIVA, Y EL DESAGÜE DEL
APARATO NO ESTÁ CONECTADO DIRECTAMENTE A
UN DESAGÜE DE PISO.
OMCAN N’EST PAS RESPONSABLE DES DOMMAGES
DUS AUX FUITES D’EAU. LA GARANTIE POUR LES
FUITES D’EAU EST ANNULÉE SI LA TEMPÉRATURE
AMBIANTE DE LA PIÈCE DÉPASSE 75°F ET 55%
D’HUMIDITÉ RELATIVE, ET SI LE DRAIN DE
L’APPAREIL N’EST PAS RACCORDÉ DIRECTEMENT
À UN DRAIN DE PLANCHER.

4
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has su󰀨ered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.

5
RESIDENTIAL USERS: vendor assumes no liability for parts or labor coverage for component failure
or other damages resulting from installation in non-commercial or residential applications. The right
is reserved to deny shipment for residential usage; if this occurs, you will be notied as soon as
possible.
1 YEAR PARTS AND LABOUR WARRANTY
Safety and Warranty
General Information
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre lea y familiarizarse con todas las instrucciones de
funcionamiento y seguridad.
Omcan le gustaría darle las gracias por la compra de esta máquina. Es de la mayor importancia para
salvar estas instrucciones para futuras consultas. Además, guarda la caja original y el embalaje para el
envío del equipo si servicio técnico o devolución de la máquina que se requiere.

6
Safety and Warranty
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule an Omcan authorized
service technician to repair the equipment locally.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not
improper use.
Please see https://omcan.com/disclaimer for complete info.
WARNING:
The packaging components are classied as normal solid urban waste and can therefore be disposed of
without di󰀩culty.
In any case, for suitable recycling, we suggest disposing of the products separately (di󰀨erentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!

7
Technical Specications
Model FR-CN-0005 FR-CN-0009 FR-CN-0014
Capacity 120 L / 4.2 cu.ft. 290 L / 10.2 cu.ft. 450 L / 15.9 cu.ft.
Maximum Load 264.6 lbs. / 120 kgs. 639.3 lbs. / 290 kgs. 992.1 lbs. / 450 kgs.
Temperature Range -26 to 0°C / -15 to 32°F
Max Ambient Temp
Rating 24°C / 75°F
Temperature
Controller Type Digital
Electrical 110-120V / 60Hz / 1
Power 210 W 260 W 295 W
Power Consumption 1.469 kW per hour 2.208 kW per hour 2.781 kW per hour
Current 2A 3A 4A
Refrigerant and
Injection R290 / 56.7g R290 / 79.9g R290 / 104.9g
Defrosting Manual
Climate Class N/ST
Insulation Material C5H10
Compressor HP 1/4+ 2/5+ 2/3+
Number of Doors 2
Number of Pans 5 9 14
Number of Casters 4 6
Dimensions 26.2” x 28.1” x 52.2”
665 x 715 x 1325mm
49.6” x 28.1” x 52.2”
1260 x 715 x 1325mm
70.9” x 28.1” x 52.2”
1800 x 715 x 1325mm
Weight 154.3 lbs. / 70 kgs. 198.4 lbs. / 90 kgs. 257.9 lbs. / 117 kgs.
Cabinet Packaging
Dimensions
29.1” x 29.9” x 37.4”
740 x 760 x 950mm
52.6” x 29.9” x 37.4”
1335 x 760 x 950mm
73.8” x 29.9” x 37.4”
1875 x 760 x 950mm
Glass Packaging
Dimensions
26.2” x 23” x 0.5”
665 x 584 x 13mm
51” x 23” x 0.5”
1295 x 584 x 13mm
72.8” x 23” x 0.5”
1850 x 584 x 13mm
Packaging Weight 169.8 lbs. / 77 kgs. 231.5 lbs. / 105 kgs. 313.1 lbs. / 142 kgs.
Item Number 47742 47743 47744

8
Installation
Operation
TRANSPORTATION AND PLACEMENT
• When transporting the chest freezer from one place to another, the inclination of the cabinet should not
exceed 45 degrees, for prevention against compressor or system damage.
• Before use, remove all the packing material. The back side of the cabinet should be more than 20cm /
7.87” away from the wall, both ank sides more than 20cm / 7.87”.
• The freezer should be put in well-ventilated, dry place. Don’t use it under direct sunshine. The freezer
should be kept away from water sink, heat source and any volatile, corrosive material.
POWER SOURCE AND TEST-RUNNING
• Specied capacity of the wire is 6A. Section squares of the wire is 0.75mm. Single line or compound lines
are all allowed. The fuse of 2.5A specied electric current should be installed. (Power cord should be
replaced with the same of 6A and 0.75mm, when it is damaged).
• Single-phase power supply, 60Hz, voltage 110-120V. If the voltage is unstable, please install a voltage
stabilizer with capacity above 1000W.
• Avoid turning on and o󰀨 the power too frequently. If the power is turned o󰀨, wait an interval of 5 minutes
before turning it on again.
• When the freezer will be out of use for a long time, disconnect the power rst, then clean it. Please
examine the circuit whether it is excellent before reuse.
ADJUSTING OF THE TEMPERATURE
• The temperature in the cabinet can be controlled with the temperature control screw and can be adjusted
using a at head screwdriver.
• FREEZING MAX is the strongest cooling position and is suitable for fast freezing. Do not keep the screw at
this point for long.
FOOD STORAGE
• There must be space between the foods stored in the cabinet, between the foods and the inner surface
of the cabinet, so as to keep good ventilation of cold air and freeze evenly. Do not put in any bottled or
canned beverage with freezing point above the temperature in the cabinet when it is below zero.
• For foods that should be moisture-free or lose water easily, wrap them up with hermetic food bags or fresh
lms before putting in the cabinet for the sake of avoiding smell-mixing and reducing frosting.
• Storage of volatile and combustible gases, liquids such as strong alkalies, strong acids, petrol, etc. is
forbidden.

9
Maintenance
Troubleshooting
Symptom Cause Solution
The indicator is not on or the
compressor does not start.
The plug isn’t connected to the
socket.
Re-connect it.
No power. Connect to a socket with power.
The indicator is on, but the
compressor doesn’t work and
buzzes only.
The power voltage is <110-120V. Attach a power-regulator with more
than 1000W power.
The compressor stops a minute
after start, and restart after a few
minutes, and so repeatedly.
The power voltage is >110-120V.
• The freezer should be cleaned regularly. When cleaning, turn o󰀨 the power, take out the foods in the
cabinet, clean the inside using water or a little neutral detergent.
• Do not use boiling water, acid, chemical diluters, petrol and oil, or dirt-removing powder.
• Dry it after cleaning.
• Use light soap water when cleaning the door seal, apply a little of talcum powder on it after natural drying to
extend its service life.
• Use a soft cloth with water or a little detergent to clean the out surface.
Note: keeping the power supply and lower part of connect wires away from water to avoid
electricity leakage.
• Except common breakdowns, those who are not service technician should not take apart and repair the
freezer on their own so as to avoid worsening the trouble. Unauthorized repair of electrical part such as
compressor, temperature controller is forbidden.
DEFROSTING
• Defrost for better freezing e󰀩ciency when the frost lm in the cabinet is 4-5mm thick.
• When defrosting, turn o󰀨 the power, take out the frozen foods, open the door for warming and melting. Use
a soft cloth to absorb water and clean it up.
• Do not use sharp metal tools such as steel brush to clean the frost lm when defrosting so as to avoid
evaporator damage.

10
Troubleshooting
The compressor works normally,
but the temperature in the cabinet
cools too slowly.
The door is being opened too
frequently.
Reduce open times.
The is too much food in the
cabinet, and it is placed improperly.
Place food properly, keep space
between them for ventilation of
cold air.
The frost lm is too thick. Take out food and defrost.
The surface of the condenser is
too dirty.
Stop and clean the condenser.
The door doesn’t seal. Adjust the door seal.
The noise is too loud. The freezer is placed in a unstable
location.
Place it in a stable location.
The xing of the freezer is loose. Tighten the xing.
There’s contact between pipes. Separate the pipes.
THE FOLLOWING ARE WITHIN NORMAL OPERATING PARAMETERS:
• When the freezer is working or after is stops for a while, the refrigerant in the pipes is cycling and gives out
“running water” sounds.
• The surface temperature of the compressor may be up 70°C ~ 80°C / 158°F ~ 176°F when it is working.
• The back side of step freezer gives out heat.
• In rainy season, the outer surface of the cabinet may have dew, which makes no defects on normal use.
Just dry it with a piece of cloth.
For service call 1-800-465-0234.

11
Model FR-CN-0005 47742
Parts Breakdown

12
Parts Breakdown
Item No. Description Position Item No. Description Position Item No. Description Position
AN902 Upper Glass Door Assembly for 47742 1 AN917 Lamp Switch for 47742 17 AN931 ST 4.8x13 Self Tapping Screw for 47742 35
AN903 Key and Lock for 47742 2 AN918 Temperature-Controlled Wiring for 47742 18 AN932 Compressor Baseboard for 47742 36
AN904 Lower Glass Door Assembly for 47742 3 AN919 JIS 4x16 Self Tapping Screw for 47742 19 AN933 Rubber Washer for 47742 37
AK372 Stainless Steel Pan 5L for 47742 4 AN920 Compressor Cover for 47742 20 AN934 Sleeving for 47742 38
AN905 Food Storage Boxes for 47742 5 AN921 Fan Motor for 47742 21 AN935 Washer for 47742 39
AN906 Stainless Steel Bracket Assembly for
47742 6 AN922 Fan Bracket for 47742 22 AN936 Screw 6x30 for 47742 40
AN907 Self Tapping Screw 3.9x16 for 47742 7 AN923 M6x14 Tapping Screw for 47742 23 AN937 Compressor for 47742 41
AN908 Temperature Display Probe Cover for
47742 8 AN924 M6 Nut for 47742 24 AN938 Compressor Starter for 47742 42
AN909 Cabinet for 47742 9 AN925 ST 4.2x13 Self Tapping Screw for 47742 25 AN939 Compressor Protector for 47742 43
AN910 Condenser for 47742 10 AN926 Filter Bracket Connecting Plate for 47742 26 AN940 Compressor Housing for 47742 44
AN911 M5x16 Tapping Screw with Washer for
47742 11 AN620 Filter Support for 47742 27 AN941 Interior Wire for 47742 45
AN912 Water Proof Box for 47742 12 AN927 Filter for 47742 28 AN942 Power Cord for 47742 46
AN913 LED Light Transformer for 47742 13 AN928 M4x8 Tapping Screw and Serrated Lock
Washers for 47742 30, 31 AN943 Castor with Brakes for 47742 47
AN914 Electronic Thermostat for 47742 14 AN929 M4x16 Tapping Screw for 47742 32 AN944 JIS 5x13 Self Tapping Screw for 47742 48
AN915 JIS 4x12 Self Tapping Screw for 47742 15 AN623 Wire Clamp for 47742 33 AN945 U-Iron for 47742 49
AN916 Electronic Temperature Control Bracket
for 47742 16 AN930 Castor for 47742 34 AI312 Led Bar for 47742 50
Model FR-CN-0005 47742

13
Model FR-CN-0009 47743
Parts Breakdown

14
Parts Breakdown
Item No. Description Position Item No. Description Position Item No. Description Position
AN946 Upper Glass Door Assembly for 47743 1 AN918 Temperature-Controlled Wiring for 47743 17 AN932 Compressor Baseboard for 47743 35
AN903 Key and Lock for 47743 2 AN919 JIS 4x16 Self Tapping Screw for 47743 18 AN951 Rubber Washer for 47743 36
AN947 Lower Glass Door Assembly for 47743 3 AN920 Compressor Cover for 47743 19 AN952 Sleeving for 47743 37
AK372 Stainless Steel Pan 5L for 47743 4 AN921 Fan Motor for 47743 20 AN953 Washer for 47743 38
AN948 Stainless Steel Bracket Assembly for
47743 5 AN922 Fan Bracket for 47743 21 AN954 Screw 6x30 for 47743 39
AN907 Self Tapping Screw 3.9x16 for 47743 6 AN923 M6x14 Tapping Screw for 47743 22 AN955 Compressor for 47743 40
AN908 Temperature Display Probe Cover for
47743 7 AN924 M6 Nut for 47743 23 AN956 Compressor Starter for 47743 41
AN949 Cabinet for 47743 8 AN925 ST 4.2x13 Self Tapping Screw for 47743 24 AN957 Compressor Protector for 47743 42
AN950 Condenser for 47743 9 AN926 Filter Bracket Connecting Plate for 47743 25 AN958 Compressor Housing for 47743 43
AN911 M5x16 Tapping Screw with Washer for
47743 10 AN620 Filter Support for 47743 26 AN941 Interior Wire for 47743 44
AN912 Water Proof Box for 47743 11 AN927 Filter for 47743 27 AN942 Power Cord for 47743 45
AN913 LED Light Transformer for 47743 12 AN928 M4x8 Tapping Screw and Serrated Lock
Washers for 47743 29, 30 AN943 Castor with Brakes for 47743 46
AN914 Electronic Thermostat for 47743 13 AN929 M4x16 Tapping Screw for 47743 31 AN944 JIS 5x13 Self Tapping Screw for 47743 47
AN915 JIS 4x12 Self Tapping Screw for 47743 14 AN623 Wire Clamp for 47743 32 AN945 U-Iron for 47743 48
AN916 Electronic Temperature Control Bracket
for 47743 15 AN930 Castor for 47743 33 AI312 LED Bar for 47743 49
AN917 Lamp Switch for 47743 16 AN931 ST 4.8x13 Self Tapping Screw for 47743 34
Model FR-CN-0009 47743

15
Model FR-CN-0014 47744
Parts Breakdown

16
Item No. Description Position Item No. Description Position Item No. Description Position
AN959 Stainless Steel Screw M5x20 for 47744 1 AN915 JIS 4x12 Self Tapping Screw for 47744 19 AN931 ST 4.8x13 Self Tapping Screw for 47744 39
AN960 Tie Bar for 47744 2 AN916 Electronic Temperature Control Bracket
for 47744 20 AN932 Compressor Baseboard for 47744 40
AN961 Upper Glass Door Assembly for 47744 3 AN917 Lamp Switch for 47744 21 AN967 Rubber Washer for 47744 41
AN907 Self Tapping Screw 3.9x16 for 47744 4 AN918 Temperature-Controlled Wiring for 47744 22 AN968 Sleeving for 47744 42
AN962 Glass Door Stop Block for 47744 5 AN919 JIS 4x16 Self Tapping Screw for 47744 23 AN969 Washer for 47744 43
AN963 Key and Lock for 47744 6 AN920 Compressor Cover for 47744 24 AN970 Screw 6x30 for 47744 44
AN964 Lower Glass Door Assembly for 47744 7 AN921 Fan Motor for 47744 25 AN971 Compressor for 47744 45
AK372 Stainless Steel Pan 5L for 47744 8 AN922 Fan Bracket for 47744 26 AN972 Compressor Starter for 47744 46
AN948 Stainless Steel Bracket Assembly for
47744 9 AN923 M6x14 Tapping Screw for 47744 27 AN973 Compressor Protector for 47744 47
AN906 Stainless Steel Bracket Assembly for
47744 10 AN924 M6 Nut for 47744 28 AN974 Compressor Housing for 47744 48
AN905 Food Storage Boxes for 47744 11 AN925 ST 4.2x13 Self Tapping Screw for 47744 29 AN941 Interior Wire for 47744 49
AN908 Temperature Display Probe Cover for
47744 12 AN926 Filter Bracket Connecting Plate for 47744 30 AN942 Power Cord for 47744 50
AN965 Cabinet for 47744 13 AN620 Filter Support for 47744 31 AN943 Castor with Brakes for 47744 51
AN966 Condenser for 47744 14 AN927 Filter for 47744 32 AN944 JIS 5x13 Self Tapping Screw for 47744 52
AK760 Metal Washers for 47744 15 AN928 M4x8 Tapping Screw and Serrated Lock
Washers for 47744 34, 35 AN945 U-Iron for 47744 53
AN912 Water Proof Box for 47744 16 AN929 M4x16 Tapping Screw for 47744 36 AI312 LED Bar for 47744 54
AN913 LED Light Transformer for 47744 17 AN623 Wire Clamp for 47744 37
AN914 Electronic Thermostat for 47744 18 AN930 Castor for 47744 38
Parts Breakdown
Model FR-CN-0014 47744

17
Model FR-CN-0005 47742
Electrical Schematics

18
Electrical Schematics
Model FR-CN-0009 47743
Model FR-CN-0014 47744

19
Warranty Registration
Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,
cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:
Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la
carte au niveau de la perforation, puis l’envoyer à l’adresse spécié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:
Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear o󰀨 the card at
the perforation and then send to the address specied below. You can also register online by visiting:
OMCAN
PRODUCT WARRANTY REGISTRATION
3115 Pepper Mill Court,
Mississauga, Ontario
Canada, L5L 4X5
https://omcan.com/warranty-registration/
or email to: [email protected]
Purchaser’s Information
Name: Company Name:
Address:
Telephone:
City: Province or State: Postal or Zip: Email Address:
Country: Type of Company:
Restaurant Bakery Deli
Dealer from which Purchased: Butcher Supermarket Caterer
Dealer City: Dealer Province or State: Institution (specify):
Invoice: Other (specify):
Model Name: Model Number: Serial Number:
Machine Description:
Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):
Would you like to extend the warranty? Yes No

Por correo en Canadá
Pour postale au Canada
For mailing in Canada
Por correo en los EE.UU.
Pour di󰀨usion aux États-Unis
For mailing in the US
OMCAN
PRODUCT WARRANTY REGISTRATION
4450 Witmer Industrial Estates, Unit 4,
Niagara Falls, New York
USA, 14305
Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan

Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North
American food service industry. Our success over these many years can be attributed to our commitment
to strengthen and develop new and existing relationships with our valued customers and manufacturers.
Today with partners in North America, Europe, Asia and South America, we continually work to improve
and grow the company. We strive to offer customers exceptional value through our qualied local sales
and service representatives who provide convenient access to over 6,500 globally sourced products.
Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et
matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces
nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles
et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en
Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et
développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à
nos ventes locales qualiées et des représentants de service qui offrent un accès facile à plus de 6500
produits provenant du monde entier.
Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros
de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir
a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos
clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan
continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor
excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un
fácil acceso a más de 6,500 productos con origen a nivel mundial.