Omcan MT-IT-370 User manual

Revised - 08/10/2023
Toll Free: 1-800-465-0234
Fax: [phone]
Email: [email protected]
www.omcan.com
Meat Tenderizer
Model MT-IT-370
Item 47709
Instruction Manual

2
Page
--------------------------------------------------------------------------- 3 - 4
--------------------------------------------------------------------------- 4 - 8
-------------------------------------------------------------------------- 8
------------------------------------------------------------------ 9 - 11
--------------------------------------------------------------------------------------- 12
----------------------------------------------------------------------------------- 12
----------------------------------------------------------------------------- 13 - 14
---------------------------------------------------------------------------- 15 - 18
---------------------------------------------------------------------------- 19
------------------------------------------------------------------------------------------- 20 - 22
---------------------------------------------------------------------------- 23
Table of Contents
Section
General Information
Safety and Warranty
Technical Specications
Installation and Operation
Maintenance
Troubleshooting
Figure Drawings
Parts Breakdown
Electrical Schematics
Notes
Warranty Registration
Model MT-IT-370

3
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has su󰀨ered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.

4
General Information
Safety and Warranty
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre lea y familiarizarse con todas las instrucciones de
funcionamiento y seguridad.
Omcan le gustaría darle las gracias por la compra de esta máquina. Es de la mayor importancia para
salvar estas instrucciones para futuras consultas. Además, guarda la caja original y el embalaje para el
envío del equipo si servicio técnico o devolución de la máquina que se requiere.
CAUTION!
The symbols used in this manual draw the reader’s attention to points and operations that are hazardous to the
operator’s personal safety or that risk damaging the machine. Do not use the machine unless you have read
and properly understood these notes.
CAUTION!
For reasons of clarity, some of the illustrations appearing in this manual show the machine or parts of it with its

5
Safety and Warranty
panels or guards removed. Never use the machine in this condition; only use it when it is fully equipped with
the guards and in good working order. The manufacturer forbids the reproduction, even partial, of this manual
or the use of its contents for purposes other than those expressly allowed. Any breach in this regard shall be
punishable by law.
STORING AND USING THIS MANUAL
This manual uses text and illustrations to familiarise users with the machine and explain the instructions and
essential criteria for its transport, handling, use and maintenance. Read this manual carefully before using the
machine. Store this manual with care near the machine so that it can be readily available for future reference.
If the manual is lost or damaged, you can request a copy from your dealer or directly from the manufacturer.
If you sell on the machine, report the new owner’s identication and address to the manufacturer. The manual
reects the state of knowledge at the time of sale of the machine, and cannot be considered inadequate in the
light of more recent experience and updates. The manufacturer reserves the right to update the products and
manuals without being obliged to update previous products and manuals, except in exceptional circumstances.
In case of doubt, contact your local service centre or the manufacturer. The manufacturer is committed to
continuously improving its products. For this reason, the manufacturer welcomes any reports or proposals
geared towards improving the machine and/or the manual. The machine is delivered to the customer with the
warranty conditions applicable at the time of sale. Please contact your dealer for any further information.
WARRANTY
The user is not authorised to tamper with the machine in any way. Contact the manufacturer if you encounter
any anomalies. Any attempt to dismantle, modify or tamper with any part of the machine by the user or
unauthorized personnel will immediately void the warranty and relieves the manufacturer of any liability for
damages deriving from such action. The manufacturer is also relieved of all liability for the consequences of:
• Improper installation.
• Improper use of the machine by inadequately trained persons.
• Use in violation of local regulations.
• Lack of or negligent maintenance.
• Use of non-original spare parts, not specied for the model in question.
• Total or partial failure to follow the instructions.
MACHINE DESCRIPTION
The machine you have purchased is a straightforward, compact machine guaranteeing powerful operation and
high performance. Since it is used for processing food products, all components that come into contact with the
food products have been carefully selected to ensure the utmost hygiene.
• The casing is made of stainless steel.
• The cover is made of stainless steel for guaranteeing maximum hygiene and facilitating cleaning
operations.
• The tools are made of stainless steel to ensure longer durability and maximum hygiene.
• The blade rollers can be rapidly dismantled for quick cleaning.
• Ventilated motors o󰀨ering the following advantages:
- Extremely constant performance and long motor life.

6
Safety and Warranty
- Longer actual work time thanks to fewer interruptions.
- Low level of heating so that the processed meat stays constantly fresh and unaltered.
The models appearing in this manual are manufactured in conformity to the UL 763, CSA 22.2 no. 195 and
NSF 8 standards. If any accident occurs, the manufacturer shall not be held liable if the machine has been
modied, tampered with, had its safety guards removed or is used for purposes other than the intended use
specied by the manufacturer.
INTENDED USE
The machine is designed and built for tenderizing steaks and cutting meat and similar products into strips. It
must be used in a professional setting by qualied operators who have read and understood this manual. Use
the machine exclusively when it is securely placed on a solid worktable.
CAUTION! The product to be processed must not be larger than the loading mouth.
IMPROPER USE
The machine must only be used for its intended purposes; in particular:
• Do NOT use the machine for processing food products other than meat and similar.
• Do NOT use the machine unless it has been properly installed with all its guards in good working order and
correctly tted, to prevent the risk of serious personal injury.
• Do NOT access any of the electrical components without having rst disconnected the machine from the
mains power supply: risk of electric shock.
• Do NOT process products larger than the loading mouth.
• Do NOT wear clothing that fails to comply with the accident-prevention regulations.
• Consult your employer for information on the applicable safety regulations and the personal protective
equipment to be worn.
• Do NOT start the machine if it has a fault.
• Before using the machine, make sure that any potentially hazardous conditions have been adequately
eliminated. If you notice anything unusual in its operation, shut down the machine and inform the
maintenance supervisors.
• Do NOT allow unauthorized persons to intervene on the machine.
Urgent treatment in case of accidents caused by electricity involves rst detaching the injured person from
the conductor (since the person is usually unconscious). This is highly hazardous. In this instance, the injured
person is also a live electrical conductor; touching them directly would mean su󰀨ering electric shock. It is
advisable to disconnect the contacts directly from the line’s power supply valve; should this not be possible,
move the victim away using insulating material (wooden or PVC sticks, fabric, leather, etc.). First-aid medical
assistance should be requested promptly and the injured person should be taken to hospital.
WARNING AND DANGER SIGNS (FIG. 1.7.2)
CAUTION!
Do not intervene on the electrical components when the machine is connected to the mains power supply.
You risk getting an electric shock. Observe the warnings signalled by the signs. Failure to do so could lead to

7
Safety and Warranty
personal injury. Make sure that the signs are always present and legible. If they are not, apply or replace them.
GUARDS AND SAFETY DEVICES
CAUTION!
Before using the machine, make sure that its safety devices are properly positioned and in good working
order. Check that they are present and work properly at the start of each shift. If not, notify the maintenance
supervisor.
WORK POSITION
To optimize work with the machine, the operator should assume the position shown in Fig. 1.9.1.
VIBRATIONS
The vibrations which the machine transmits to the work surface are negligible.
ENVIRONMENTAL CONDITIONS
The machine is designed to work in the following environmental conditions:
• Minimum room temperature: –5°C.
• Maximum room temperature: +40°C.
• Relative humidity: 50% at 40°C.
LIGHTING
The machine must be installed in a place that ensures adequate natural and articial lighting as required by
local regulations in the country of installation. At all events, the lighting must comply with the local regulations
in force in the country of installation and should not generate hazardous reections. The lighting system must
ensure clear reading of the control panels and the start and stop buttons must be clearly identiable.
SAFETY EQUIPMENT
No special equipment is required. We advise using regulatory rubber gloves suited for working with food
products.
RESIDENTIAL USERS: vendor assumes no liability for parts or labor coverage for component failure
or other damages resulting from installation in non-commercial or residential applications. The right
is reserved to deny shipment for residential usage; if this occurs, you will be notied as soon as
possible.
1 YEAR PARTS AND LABOUR BENCH WARRANTY
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule a drop o󰀨 to either

8
Safety and Warranty
an Omcan authorized service depot in the area, or to an Omcan Service warehouse to repair the
equipment.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not
improper use.
Please see https://omcan.com/disclaimer for complete info.
WARNING:
The packaging components are classied as normal solid urban waste and can therefore be disposed of
without di󰀩culty.
In any case, for suitable recycling, we suggest disposing of the products separately (di󰀨erentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!
Technical Specications
Model MT-IT-370
Power 0.5 HP / 370 W
Electrical 110-120V / 60Hz / 1
Drum RPM 110
Feed Opening 10” x 1.2” / 254 x 30mm
Dimensions 18” x 13.5” x 20.2” / 457 x 343 x 513mm
Packaging Dimensions 29” x 23” x 31” / 737 x 584 x 787mm
Weight 77 lbs. / 34.9 kgs.
Packaging Weight 99 lbs. / 44.9 kgs.
Item Number 47709

9
Installation and Operation
CONTROLS AND INDICATORS
LIST OF CONTROLS AND INDICATORS (FIG. 3.1.1)
1. Run button.
- Press to start the machine.
2. Stop button.
- Press to stop the machine.
3. Start button LED.
- Lights up when the start button is pressed.
FACTORY TESTING, SHIPPING, DELIVERY AND INSTALLATION
FACTORY TESTING
The machine you have purchased has been tested at our plants to verify its correct operation and proper
adjustment. The tests were conducted using materials similar to those processed by the user.
DELIVERY AND HANDLING
All shipped material is carefully checked prior to being handed over to the shipping agent. Unless otherwise
agreed with the customer, the machine is wrapped in nylon and strapped to the pallet. It is then covered with
cardboard, which is also strapped to the pallet. When you receive the machine, check the condition of its
packaging. If you notice any damage to the packaging, sign the delivery note with the following note: “Goods
accepted with reservation...” and the reason. If you notice any damage to the components of the machine after
opening the package, report it to the shipping agent within three days from the date shown on the documents.
INSTALLATION
CAUTION!
The installation zone must be level and solid, while the surface on which the machine rests must provide
stable and safe support. Moreover, the machine must be placed where there is ample space around it. This will
facilitate manoeuvring during work phases and ensure easy access for subsequent maintenance operations.
Provide adequate lighting around the machine to ensure good visibility for the operator using it. Remove the
cellophane wrapping and any other packaging present inside.
DISPOSAL OF PACKAGING
The packaging materials (cardboard, nylon, wood, etc.) can be regarded as solid urban waste. As a result,
they can be disposed of freely. Nylon is a polluting substance that releases toxic fumes when burnt. Do not
burn or dump it, but dispose of it according to the law. If the machine is delivered to a country where special
regulations apply, dispose of the packaging accordingly.

10
Installation and Operation
HANDLING THE MACHINE
CAUTION!
Take care when handling the machine: dropping it accidentally can seriously damage it. To avoid muscle
injuries, lift the machine by exing your legs.
ELECTRICAL CONNECTIONS
CAUTION!
Check that the power supply line has the same specications as those shown on the machine’s rating plate.
All interventions must be carried out solely by specialised personnel expressly authorised by the relevant
supervisor. Make the connection to a power line equipped with an e󰀩cient earthing socket.
In this conguration, the machine is supplied with a power cable with 3 x 18 AWG. It is connected to a NEMA
5-15P plug. Attach the power cable to the 110-120 V - 60 Hz singlephase power supply line by installing a 10
A residual-current circuit breaker in between. Consult the manufacturer for congurations di󰀨ering from those
mentioned above. If the power cable needs to be extended, use a cable of the same gauge as the original
cable installed by the manufacturer.
START-UP AND SHUTDOWN
VERIFICATION OF THE CORRECT ELECTRICAL CONNECTION
Plug the cable into the power socket; press the run button (“1”, Fig. 3.1.1).
Note: in machines connected to a single-phase line and specically designed for this system, the
rotation direction will be dened directly by the manufacturer.
VERIFICATION OF THE PRESENCE AND EFFICIENCY OF GUARDS AND SAFETY DEVICES
With the machine connected to the mains electricity, open the tool cover. The machine must stop.
VERIFICATION OF THE EFFICIENCY OF THE EMERGENCY STOP BUTTON (FIG. 3.1.1)
With the machine connected to the electricity and the accessory tool moving, press the stop button (2). The
machine must stop.
MACHINE START-UP (FIG. 3.1.1)
To start the machine, plug it into the power outlet then press the start button (“1” Fig. 3.1.1).
MACHINE STOP (FIG. 3.1.1)
To stop the machine, simply press the stop button (“2” Fig. 3.1.1).

11
Installation and Operation
USING THE MACHINE
CAUTION!
Only authorised personnel may intervene on the machine. Before using the machine, the operator must
ensure that all guards are in place and that the safety devices are present and working e󰀩ciently. If this is not
the case, switch the machine o󰀨 and contact the maintenance supervisor. Make sure that the product to be
tenderized/cut does not have any bones, nerves or others hard parts that can ruin the blades. The size of the
product to be tenderized/cut must have a suitable size for tting inside the loading mouth. NEVER PUSH THE
PRODUCT WITH YOUR HANDS.
PREPARING THE BLADE CARTRIDGE
The machine can be congured with 2 di󰀨erent meat processing rollers:
1. Tenderizing rollers.
2. Cutting rollers.
- The “tenderizing” system is made up of star-shaped blades (Fig. 6.2.1) that penetrate the meat and curt
the nerves so as to make it more tender.
- The “strip-cutting” system is made up of round blades (Fig. 6.2.2) paired with one another that cut the
meat into strips; strips of di󰀨erent thickness can be obtained by varying the thickness of the spacers.
- To insert the blade roller, turn the blade cartridge knob so that the slot opens (position “1” Fig. 6.2.3 – the
knob will click slightly).
- Insert the roller by gripping it from the ends. Do not touch the blades with your hands.
- Turn the cartridge knob in the opposite direction to lock the roller (position “2” Fig. 6.2.3 – the knob will
click slightly).
- Insert the scraping combs (Ref. 3 Fig. 6.2.4).
- Move the cartridge using the handle (Ref. 4 Fig. 6.2.3).
AUTOMATIC VERSION
• Raise the interlocked blade guard (Ref. 4 Fig. 6.4.1).
• Place the cartridge on the bars of the base (Ref. 1 Fig. 6.4.1).
• Turn the cartridge lever (Ref. 5 Fig. 6.4.1) so that the blade roller pins insert into the drive pins, until they
slot into place.
• Close the interlocked blade guard (Ref. 4 Fig. 6.4.1).
• Press the controls (Ref. 3 Fig. 6.4.1) to switch the machine on or o󰀨.
• Take the product with two hands and insert it into the loading mouth; use the pestle if the product gets
jammed.
CAUTION: handle the blade cartridge always through the appropriate handle (Ref. 2 Fig. 6.4.1) and
protect the hands with cut-resistant gloves.

12
Maintenance
CAUTION!
Maintenance and cleaning must always be carried out with the machine at a standstill and disconnected from
the mains power supply. Always keep the maintenance zone clean and dry. Do not allow unauthorized persons
to intervene on the machine. Parts and tools must be replaced using original spare parts at authorised service
centres, or directly by the manufacturer.
LUBRICATION
The machine does not require any lubrication.
CLEANING THE MACHINE
CAUTION!
Disconnect the machine from the mains power supply before cleaning it. Do not clean the machine using
a water jet. Only use non-toxic detergents specically formulated for cleaning components used with food
products. The knives are made of AISI 430 grade steel, therefore rust may form if they are left immersed or
wet. We suggest drying them after they are washed.
• Turn the interlocked blade cover (Ref. 4 Fig. 6.4.1) by 90° and push it towards the left: the blade guard will
come o󰀨.
• Detach the blade cartridge lever (Ref. 5 Fig. 6.4.1).
• Take the cartridge (Ref. 2 Fig. 6.4.1) o󰀨 the bars of the base using the handle and pull it so that the blade
pins detach from the drive mechanism.
• Place the cartridge on the bars of the base (Ref. 1 Fig. 6.4.1).
• Put the blade cartridge and the guards in the dishwasher.
• Wash the base by hand using non-aggressive detergents.
• After completing the cleaning operations, assemble all the components by following the instructions in
reverse order.
Troubleshooting
Malfunctions Causes Remedies
The machine does not start. The residual current circuit breaker
is set to “0”.
Set the switch to “I”.
The plug switch is set to “0”. Set the switch to “I”.
The start button does not work. Contact the technical assistance
service.
The safety devices are not all
present or mounted properly.
Check the safety devices.
The product is not cut correctly. The knives of the blade roller are
blunt.
Sharpen the knives or replace
them.

13
Figure Drawings

14
Figure Drawings
Item 47709

15
Parts Breakdown
Model MT-IT-370 47709
Item 47709

16
Parts Breakdown
Model MT-IT-370 47709

17
Parts Breakdown
Model MT-IT-370 47709
Item No. Description Position Item No. Description Position Item No. Description Position
AN344 Cable 3x14AWG+Plug UL 15A 125V 3MT
for 47709 1 61583 Nut Din 1587 M6 for 47709 16 AN391 Carter Closing Post Int.Bis.Aut for 47709 35
AN345 Wheel Release Int.Bis.Aut for 47709 1 AN365 Bearing 61804 2RS for 47709 16 AN392 Carter Closing Side Int.Bis.Aut for 47709 36
61604 Strain Relief + Nut for 47709 2 AN366 Screw TE Din 933 M6x12 T.F. for 47709 17 AN393 Dist. Cutting Blades SP 8 Int.Bis.Aut
for 47709 37
AN346 Blades Fixing Knob for 47709 2 AN367 Bearing 61801 2RS for 47709 17 AN394 Support Bracket Rods Basket Int.Bis.
Aut for 47709 37
61603 Nut Ott.Nich.PG 11 for 47709 3 AN368 Ball Bearing 32004X for 47709 18 AN395 Supp.Tendicing x UL CSA Int.Bis.Aut
for 47709 38
AN347 Basket Plate TR Blades Int.Bis.Aut for
47709 3 AN369 Screw TSP Din 963 M6x14 for 47709 18 AN396 Input Box Body Bril Int.Bis.Aut for 47709 39
62606 PG 11 Plastic Cable Gland for 47709 4 AN370 Ring 20-30-5 for 47709 19 AN397 Cover Bri Input Box Int.Bis.Aut for 47709 40
AN348 Basket Plate L.Fix.UL Int.Bis.Aut for
47709 4 AN371 Ingr. Case Gasket Fus. Int.Bis.Aut for 47709 20 AN398 Sprocket Z12 M1.5 Int.Bis.Aut for 47709 41
AG288 Plastic Nut PG 13.5 for 47709 5 AN372 Alum.Blade Spacer TH.4.2 for 47709 20 AN399 Sprocket Z40 M1.5 Int.Bis.Aut for 47709 42
AN349 Wire Handle Blades Basket Int.Bis.Aut
for 47709 5 AN373 Cap 22/4/C Int.Bis.Aut for 47709 21 AN400 Transmission Shaft Int.Bis.Aut for 47709 43
AM948 Masch.2 Puls. Acc x Capsula Silic. for
47709 6 AN374 Blade Fixing Bushing for 47709 21, 36 AN401 Drive Pin Int.Bis.Aut for 47709 44
AN350 Scraper Comb for 47709 6 AN375 Sealing Ring 3545-7 for 47709 22 AN402 Supp. Auction Cest. Blade Int.Bis.Aut
for 47709 45
AN351 Box GW 44276 UL-CSA 150x110x70
for 47709 7 AN376 Eng. Box Pulley Int.Bis.Aut for 47709 23 AN403 Basket Support Pin Int.Bis.Aut for 47709 46
AN352 Cest Union Auction Blades Int.Bis.Aut
for 47709 7 AN377 Toothed Blade D.65 4mm for 47709 23 AN404 Belt Tensioner Spring x Cut.Ind/Int.Bis. Aut for 47709 47
AN353 Card TG-TFF01 110-220 60Hz UL for
47709 8 AN378 Pul. Z50 Crankshaft Int.Bis.Aut for 47709 24 62643 Flat Washer Din 125 D 6 for 47709 48
AN354 Prot.Grid Lower Lam. Int.Bis.Aut UL/Man
for 47709 8 AN379 Belt Z29 Int.Bis.Aut for 47709 25 62644 Flat Washer Din 125 D 8 for 47709 49
AN355 Stainless Steel Button MSM-19 UL Cut
Ind for 47709 9 AN380 Dist. Plast. 25x8.4x6 Motor Int.Bis.Aut for 47709 26 62648 Blind Nut Din 1587 M5 for 47709 50
AN356 Supp Knob Fixed UL Int.Bis.Aut for
47709 9 67560 Rubber Foot 40x35 PM M8x10 for 47709 27 AH813 Retaining Rings DIN 471 D 12E for 47709 51
AH077 Magnetic Sensor Head UL TA for 47709 10 AN381 Rubber Stopper Meat Tray for 47709 28 AN405 Radial Circlips Din 6799 M8 for 47709 52
AN357 Female Screw Stainless Steel Counter-
sunk TC- Int.Bis.Aut for 47709 10 AN382 Blades Shaft for 47709 28 AN406 Radial Rings Din 6799 IX 10 for 47709 53
AN358 Hinge Assembly for 47709 11 69205 Handle 236-148 M5 Inter 94 for 47709 29 AN407 Din 6885/A 3x3x16 Tabs for 47709 54
AN359 Supp Blade Pack Release Int.Bis.Aut
for 47709 11 AN383 Blade Spacer TH.2 for 47709 29, 34 AN408 Din 6885/A 5x5x15 Tabs for 47709 55
AN360 Blade Pack Release Lever Int.Bis.Aut
for 47709 12 AN384 Mot. M71 HP 0.5 B34 4P 110/60 UL for 47709 30 AN409 Din 6885/A 6x6x20 Tabs for 47709 56
AM949 Cover Prot.Termico Monof UL CSA for
47709 13 AN385 Supp. Micro Bending Micro 100W 3A UL for 47709 31 62660 Washer F Wide Din 9021 D 6x18 for 47709 58
AN361 Blade Pack Release Pin Int.Bis.Aut for
47709 13 AN386 Blade D.72 for 47709 32 AN410 Washer Din 9021 D 8x24 for 47709 59
AM950 Protettore Termic. Monof 10A UL CSA
for 47709 14 AN387 Ass. Belt Tensioner Cut.Ind./Int. for 47709 32 AN411 Hex.Socket Head Cap Screw M8x20 for 47709 60
AN362 Blade Pack Cover x UL Int.Bis. for 47709 14 AN388 Assembly Fairing Int.Bis.Aut for 47709 33 AN412 Hex.Screw Din 933 M5x16 for 47709 61
AN363 Bearing 629 2RS for 47709 15 AN389 Plastic Cover Int.Bis.Aut for 47709 34 AN413 Hex.Screw Din 933 M6x20 T.F. for 47709 62
AN364 Mouth Protection Support Pin TC for
47709 15 AN390 Dist. Cutting Blades TH 13 Int.Bis.Aut for 47709 35 62662 Screw TE Din 933 M8x16 T.F. for 47709 63

18
Parts Breakdown
Model MT-IT-370 47709
Item No. Description Position Item No. Description Position Item No. Description Position
62663 X.Screw Din 933 M8x20 for 47709 64 69216 Self Blocking Nut ES Din 982 M8 Upper
for 47709 71 AN420 Tenderizing Blade Assy for 47709 DB04D
AN414 Screw TE Din 933 M8x40 T.F. for 47709 65 62669 Poeliers M4x10 Screw for 47709 72 AN421 Cut Pack 10mm Dist. On Mouth. Int Bis
for 47709 DB10
AN415 Screw TSP-Din 963 M6x20 for 47709 67 AM945 Poeliers Screw M5x10 for 47709 73 AN422 Cut Pack 15mm Dist. On Mouth. Int Bis
for 47709 DB15
AN416 Screw TSP-Din 963 M8x25 for 47709 68 AN417 Ground Label for 47709 74 AN423 Tenderizing Blade Assy for 47709 DT04D
60079 Self-Locking Nut ES Din 982 M5 High
for 47709 69 AN418 25 UF UL Capacitor for 47709 75 AN424 Cut Pack 10mm Dist.On Trans. Int Bis for 47709 DT10
62668 Self-Lock Nut ES Din 982 M6 High for
47709 70 AN419 Magnet Dia.17 M634 NA BA for 47709 76 AN425 Cut Pack 15mm Dist.On Trans. Int Bis for 47709 DT15

19
Electrical Schematics
Model MT-IT-370 47709

20
Notes
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________