Omcan SE-US-0533-S User manual

Revised - 04/06/2021
Toll Free: 1-800-465-0234
Fax: [phone]
Email: [email protected]
www.omcan.com
Wrapping Machine
Model SE-US-0533-S
Item 14428
Instruction Manual

2
Page
--------------------------------------------------------------------------- 3 - 4
--------------------------------------------------------------------------- 4 - 5
-------------------------------------------------------------------------- 5
------------------------------------------------------------------------ 6
------------------------------------------------------------------------------------- 6 - 7
------------------------------------------------------------------------------- 7 - 8
-------------------------------------------------------------------------------------------- 9 - 10
---------------------------------------------------------------------------- 11
Table of Contents
Section
General Information
Safety and Warranty
Technical Specications
Installation and Operation
Maintenance
Parts Breakdown
Notes
Warranty Registration
Model SE-US-0533-S

3
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.

4
General Information
Safety and Warranty
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre lea y familiarizarse con todas las instrucciones de
funcionamiento y seguridad.
Omcan le gustaría darle las gracias por la compra de esta máquina. Es de la mayor importancia para
salvar estas instrucciones para futuras consultas. Además, guarda la caja original y el embalaje para el
envío del equipo si servicio técnico o devolución de la máquina que se requiere.
WARNING
PLEASE READ THE USER MANUAL CAREFULLY BEFORE OPERATING THE MACHINE
This manual has been prepared to enable the correct installation, regulation and maintenance of the unit. It
is therefore of basic importance that the warnings contained in this booklet are carefully read as they supply
essential indications regarding the safety of the installation, use and maintenance. The appliance must be
installed, tested and serviced by qualied personnel only. Any adjustment whatsoever not expressly authorized

5
Safety and Warranty
and in disrespect of this manual voids the warranty. Observe all existing local regulations at the time of
installation. The packing materials (plastic bags, polystyrene, nails, etc.) as potential hazards, must be kept out
of the reach of children and properly recycled according to the existing local regulations. For repairs contact
Omcan and request the use of original spare parts. If in doubt do not use the appliance and contact Omcan.
Not following the above conditions could risk the safety of those using the unit.
1 YEAR PART AND LABOUR WARRANTY
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule an Omcan authorized
service technician to repair the equipment locally.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not
improper use.
Please see https://omcan.com/disclaimer for complete info.
WARNING:
The packaging components (cardboard, polyethylene, and others) are classied as normal solid urban waste
and can therefore be disposed of without difculty.
In any case, for suitable recycling, we suggest disposing of the products separately (differentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!
Technical Specications
Model SE-US-0533-S
Type One-Roll Capacity with Mounting Axle
Stretch Film 18” / 457mm maximum width
Hot Plate 6” x 15” / 452 x 381mm
Electrical 110V / 60Hz / 1
Weight 30 lbs. / 13.6 kgs.
Packaging Weight 32 lbs. / 14.5 kgs.
Dimensions 26” x 22.3” x 9” / 660 x 565 x 229mm
Packaging Dimensions 30” x 24” x 12” / 762 x 610 x 305mm
Item Number 14428

6
Maintenance
CIRCUIT BOARD TEST:
A standard 110V Neon circuit tester can be used for testing.
CHECKING FUSE:
With the power OFF, disconnect red wire from Terminal 1 and
secure it out of the way without touching any metal. With power
ON, test across Terminals 3 and 4. If tester does not light, replace
fuse.
CHECKING HOT ROD:
With the power OFF, disconnect red wire from Terminal 1 and secure it out of the way without touching any
metal. With power ON, test between Terminal 1 and end of disconnected wire. If tester does not light, replace
the hot rod.
Installation and Operation
INSTALLING COMPLETE AXLE ASSEMBLY
To install the axle assembly (1), simply position the
assembly at the rear of the machine (2) with the
removable end cap (3) on the left side as pictured above.
Insert two bolts (4) on each side through the machine
base (2) and bearing block plates (5), slide on washers
and fasten washers with hex nuts (6).
REPLACING THE INDIVIDUAL AXLE
To replace the axle, remove cap from end of one bolt (7)
and unscrew wing nut (8), then pull screw from bearing
block (9) and open to release the axle assembly, replace
axle assembly with removable cap as shown above.
LOADING AND ADJUSTING AXLE FOR DIFFERENT
WIDTH FILMS
Loosen the wing nuts and swing out upper bearing blocks
on both sides.
Lift out the axle assembly, unscrew the movable end cap
and position xed cap for lm size being used and secure with pin and o-ring (10).
Place the core of the lm against the xed cap and feed lm from bottom of roll (check threading diagrams
on previous page). Replace the movable end cap and screw tightly into lm core. Replace the axle back into
bearing blocks and then tighten wing nuts to desired lm tension.

7
Maintenance
CHECKING BOARD:
With the power OFF, disconnect red wire from Terminal 1 and secure it out of the way without touching any
metal. With power ON, test across Terminals 1 and 2. If tester does not light, replace circuit board.
WARNING: THIS UNIT SHOULD NOT BE OPERATED IF ROD TEMPERATURE EXCEEDS 275°
FAHRENHEIT. IF SMOKE OR FUMES ARE DETECTED, DISCONTINUE USE
TO LOAD FILM ON WRAPPERS WITH ROLLERS:
• Rest Film Roll on Top of Two Rollers, Centering Film Between the Plastic Guides.
• Tighten Thumb Screw Against the Film Brake to Ensure Proper Film Tension.
• Thread Film Per Diagrams Below. NOTE: Thread Rolls One at a Time or as Needed.
Parts Breakdown
Model SE-US-0533-S 14428
Item No. Description Position Item No. Description Position Item No. Description Position
15691 Core Adapter Set for 14428 1 37445 Brg. Blk. Supt. Plate for 14428 12 17542 Thinnerman Cap for 14428 23
15697 Bearing Block Set for 14428 2 15676 Insulator Washer for 14428 13 40582
Kit Film Retainer Rod 1/4” D by 22 5/8”
L Vinyl Film Retainer and Two Caps
for 14428
24
15683 Axle for 14428 3 37444 Lock Washer for 14428 14 15695 Retainer Film Guide Vinyl for 14428 25
15671 Fuse for 14428 4 37443 Hex Cap Screw for 14428 15 27860 Snap Bushing for 14428 26
15672 Fuse Holder for 14428 5 15681 Rubber Feet 4/Pack (2135-001) for 14428 16 15684 Hot Rod Collar for 14428 27
15678 Power Cord 102-107A for 14428 6 15682 Knob Thermostat 102A for 14428 17 15675 Hot Rod for 14428 28
15677 Pilot Light for 14428 7 28511 Cover with Non-Stick Coating 6x15 for
14428 18 37439 Elec. Control Hsg. for 14428 29
15679 Switch Toggle for 14428 8 15686 Hot Plate Casting for 14428 19 37438 Wrapping Bridge for 14428 30
37447 Insulator Washer for 14428 9 14769 Element for 14428 20 27859 Core Adapter Pin for 14428 31
15670 Circuit Board for 14428 10 15680 Thermostat for 14428 21 76333 Hot Plate Assembly for 14428
37446 Terminal Block for 14428 11 28499 Element Plate Retain for 14428 22

8
Parts Breakdown
Model SE-US-0533-S 14428

9
Notes
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________

10
Notes
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________

11
Warranty Registration
Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,
cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:
Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la
carte au niveau de la perforation, puis l’envoyer à l’adresse spécié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:
Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at
the perforation and then send to the address specied below. You can also register online by visiting:
OMCAN
PRODUCT WARRANTY REGISTRATION
3115 Pepper Mill Court,
Mississauga, Ontario
Canada, L5L 4X5
https://omcan.com/warranty-registration/
or email to: [email protected]
Purchaser’s Information
Name: Company Name:
Address:
Telephone:
City: Province or State: Postal or Zip: Email Address:
Country: Type of Company:
Restaurant Bakery Deli
Dealer from which Purchased: Butcher Supermarket Caterer
Dealer City: Dealer Province or State: Institution (specify):
Invoice: Other (specify):
Model Name: Model Number: Serial Number:
Machine Description:
Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):
Would you like to extend the warranty? Yes No

Por correo en Canadá
Pour postale au Canada
For mailing in Canada
Por correo en los EE.UU.
Pour diffusion aux États-Unis
For mailing in the US
OMCAN
PRODUCT WARRANTY REGISTRATION
4450 Witmer Industrial Estates, Unit 4,
Niagara Falls, New York
USA, 14305
Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan

Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North
American food service industry. Our success over these many years can be attributed to our commitment
to strengthen and develop new and existing relationships with our valued customers and manufacturers.
Today with partners in North America, Europe, Asia and South America, we continually work to improve
and grow the company. We strive to offer customers exceptional value through our qualied local sales
and service representatives who provide convenient access to over 5,000 globally sourced products.
Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et
matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces
nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles
et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en
Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et
développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à
nos ventes locales qualiées et des représentants de service qui offrent un accès facile à plus de 5000
produits provenant du monde entier.
Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros
de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir
a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos
clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan
continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor
excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un
fácil acceso a más de 5,000 productos con origen a nivel mundial.