Omcan FP-IT-0300 User manual

Food Processor
Model FP-IT-0300
Item 10927
Instruction Manual
Revised - 07/14/2017
Toll Free: 1-800-465-0234
Fax: [phone]
Email: [email protected]
www.omcan.com

2
Page
--------------------------------------------------------------------------- 3 - 4
--------------------------------------------------------------------------- 4 - 6
---------------------------------------------------------------------- 7 - 9
------------------------------------------------------------------------------------------ 10
------------------------------------------------------------------------------------- 11 - 12
--------------------------------------------------------------------------------- 12 - 14
---------------------------------------------------------------------------- 15 - 17
---------------------------------------------------------------------------- 18
---------------------------------------------------------------------------- 19
Table of Contents
Section
General Information
Safety and Warranty
Technical Specications
Installation
Operation
Maintenance
Parts Breakdown
Electrical Schematics
Warranty Registration
Model FP-IT-0300

3
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.

4
Safety and Warranty
GENERAL PRECAUTIONS
• The vegetable cutter must be operated only by highly qualied personnel who are fully aware of the safety
measures described in this manual.
• In case of a personnel turnover, training is to be provided in advance.
• Although the machine incorporates safety devices and protections for dangerous parts, it is recommended
not to touch the moving parts.
General Information
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre lea y familiarizarse con todas las instrucciones de
funcionamiento y seguridad.
Omcan le gustaría darle las gracias por la compra de esta máquina. Es de la mayor importancia para
salvar estas instrucciones para futuras consultas. Además, guarda la caja original y el embalaje para el
envío del equipo si servicio técnico o devolución de la máquina que se requiere.

5
• Before starting cleaning and maintenance operations, disconnect the plug from the electrical socket.
• To carry out cleaning and maintenance, assess the residual risks carefully (as protections are removed).
• Cleaning and maintenance require concentration.
• A regular check of the power supply cable is absolutely necessary; a worn-out or damage cord is very
dangerous.
• If the machine malfunctions, it is recommended not to use it and do not try to repair it; please call Omcan.
• Do not use the machine for processing frozen products, meat and shes with bones or non food products.
• Do not repair the machine yourself but call Omcan.
• Always use the pusher with the pestle to cut the food.
• Do not ll too much the inlet cylinder and do not press too hard to avoid any problem.
• The manufacturer shall not be liable for damage to things or injury to persons in the event:
- The machine or the safety devices and protections have been tampered with by non authorised
personnel.
- Non original spare parts and discs are installed.
- The instructions provided in this manual are not followed thoroughly.
- The machine surface is not cleaned with the right product.
SAFETY DEVICES
GENERAL SAFETY DEVICES
The mechanical, electrical and hygienic safety devices installed on the vegetable cutter described in this
manual complies with:
UL 763 and NSF Standards.
The vegetable cutter is tted with electrical and mechanical safety devices for machine operation as well as
cleaning and maintenance operations. However, there are RESIDUAL RISKS which cannot be eliminated
completely. These risks are listed in this manual under WARNINGS. These risks are cutting dangers due to the
machine handling during the disc substitution and/or cleaning.
ELECTRICAL SAFETY DEVICES
The vegetable cutter is tted with microswitches:
• On the pusher lever, to stop the machine if the handle is lifted over the mouth of the lid and to enable to
turn on the machine automatically when there is a dangerous situation.
Safety and Warranty

6
Safety and Warranty
• On the hopper, to stop the machine if the lid is removed (i.e. to replace the discs), and to permit to start the
machine voluntarily (by pressing pushbutton “I”) only when the lid is closed, correctly locked by the hinges
for the steel lid or with the knob for the aluminium lid.
1 YEAR PARTS AND LABOUR BENCH WARRANTY
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule a drop off to either
an Omcan authorized service depot in the area, or to an Omcan Service warehouse to repair the
equipment.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not
improper use.
Please see www.omcan.com/warranty.html for complete info.
WARNING:
The packaging components are classied as normal solid urban waste and can therefore be disposed of
without difculty.
In any case, for suitable recycling, we suggest disposing of the products separately (differentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!

7
Technical Specications
MACHINE DESCRIPTION
ACCESSORIES
The vegetable cutter is provided with many accessories. Some are supplied with the cutter, other must be
requested by the Client.
STANDARD ACCESSORIES
PESTLE: Made of polyethylene for alimentary use, to facilitate the cutting of small product, it must be
introduced in the product cylinder placed on the pusher.
COLLECTING BOWL: Made of polyethylene for alimentary use, “GASTRONORM” of 1/3, h=200; equipped
with microswitch.

8
Technical Specications
DISCHARGING SPATULA: Made of steel AISI 304 installed on the disc support pin. It makes easier to
discharge the product when cut. It can only be used with the following discs DTV, DT2 - 3 - 4 - 7 - 9, DF1 - 2 - 3
- 4.
DISCS HOLDER: Made of plasticised steel for alimentary use, it is a useful collector for discs.
TOOLS
On demand, the vegetable cutter can be supplied with different discs, suitable for many different cuts.
DISCS FOR SLICES “DF”:
They are made of aluminium and the knives are made of AISI 420. The following
discs are available:
• DF1.
• DF2.
• DF3.
• DF4.
• DF5 - specic for tomatoes and peppers.
• DF8.
• DF10.
• DF14.
DISCS FOR STRIPS “DT”:
The supporting structure is made of aluminum, and the body of the disc is made of
AISI 420. The following discs are available:
• DTV - to grate.
• DT2.
• DT3.
• DT4.
• DT7.
• DT9 - specic for mozzarella.
DISCS FOR MATCHSTICKS “DQ”:
The supporting structure is made of aluminium and the knives are made of AISI 420.
The following discs are available:
• DQ4.
• DQ6.

9
Technical Specications
• DQ8.
• DQ10.
DISCS FOR CUBES “PS”:
The supporting structure is made of aluminium and the knives are made of AISI 420.
The following discs are available:
• PS8 coupled with DF8.
• PS10 coupled with DF10.
• PS20 coupled with DF14.
OVERALL DIMENSIONS, WEIGHT, FEATURES
Model FP-IT-0300
Power 0.7 HP / 0.52 kW
Disc Speed 300 RPM
Mouth Opening 3 1/16” x 6 1/4” / 78 x 159mm
Electrical 110V / 60Hz / 1
Food Collection Bin/Tray 1/3-size, 7QT / 6.5L, Clear | 12.75” x 7” x 8” / 324 x 178 x 203mm
Weight 54 lbs. / 24.5 kgs.
Dimensions 20” x 11” x 19” / 508 x 279 x 483mm
Item Number 10927
Machine electrical specications are indicated on the rating plate afxed to the side of the grater; before
connecting to power supply, please see Rating Plate.

10
Installation
PACKAGING OF THE MACHINE
The vegetable cutter is accurately packed and then
despatched from our warehouses. The package
includes:
1. A solid cardboard box.
2. The machine.
3. Some elements to keep the machine stable.
4. The bowl.
5. The pestle.
6. This manual.
7. CE conformity declaration.
SETTING UP OF THE MACHINE
The vegetable cutter must be installed on a suitable
and adequate size work table, the machine must be
solid, stable and xed at a height of 80 cm from the
ground. Moreover the machine must be installed
in a room with max. 75% non saline humidity at a
temperature between +5°C and +35°C (41°F and
95°F); in a location and environment that does not
provoke malfunctions or faults in the machine.
COLLECTING BOWL
If the Vegetable cutter is provided with a collecting bowl, place it under the
mouth of the machine, so as to cover the product exit.
ELECTRICAL CONNECTION
The Vegetable cutter is equipped with a power supply cable with a SJT 16
AWG mm2 section; length 1,5 m and a NEMA 5 plug. Connect the Vegetable
cutter to 115 Volt 60 Hz, by interposing a differential thermomagnetic switch
10 A DI = 0,03 A. Check correct machine grounding. Moreover check that the
specications on the rating plate-serial number correspond to the specications
provided in the consignment and delivery note.

11
Operation
FUNCTIONAL CHECK
To check the correct machine operation, proceed as follows:
1. Turn ON push button “I” and stop push button “0” and check that the corresponding pilot lights turn on and
off.
2. Check that the motor stops and then turns on when you lift or lower the pusher handle.
3. Check that the machine stops when your remove the lid and that it turns on by pressing push button
START “I” only if the lid is correctly installed.
USE OF THE MACHINE
DISCS ASSEMBLY - CAUTION!
1. Choose one of the following discs DF 1-2-3-4-5-8-10-14, DTV, DT 2-3-4-7-9, or DQ 4-6-8-10; remove the
steel or aluminium lid, and place the disc on the shaft. Rotate the disc until it is xed. Replace the stainless
steel lid fastening it with the specic hinges or the aluminium lid fastening it with the knob.
2. TO CUT CUBES: Choose the couple of discs among PS8-DF8, PS10-DF10, PS20-DF14. Place the rst
disc PS. with the cavity turned on the right side placing yourself in front of the machine. Then install the DF
disc.
NOTE: NEVER USE THE DISCHARGING SPATULA WITH COUPLED DISCS PS-DF.
3. If the machine is supplied with a discharging spatula, we advise to use it with the following discs DF 1-2-
3-5, DTV, DT 2-3-7-9, DQ4. The spatula must be assembled on the disc support pin before any other disc.
After having assembled the spatula, proceed as in point “1”.
LOADING AND CUTTING THE PRODUCT - CAUTION!
When the machine is working, it is necessary to stand correctly to avoid accidents.
The body must always be perpendicular to the working table. Pay the maximum
attention that no members of your body enter in contact with the machine.

12
Maintenance
IMPORTANT
Before performing any maintenance operation, it is necessary to disconnect the plug from the mains to isolate
it from the mains power supply.
BELT
The drive belt does not require adjustment. In general after 3-4 years, it must be replaced, in this case call
Omcan.
FEET
Feet may deteriorate or lose elasticity, reducing machine stability. If support feet show signs of wear or
damage, replace.
POWER SUPPLY CABLE
Periodically check for wear in the power supply cable. If the power supply cable shows signs of wear or
damage call Omcan for a replacement.
Operation
NOTE: The product has to be loaded in the Vegetable Cutter when it is OFF.
Proceed as follows:
1. Load the product in the mouth of the lid. If the product is small (i.e. carrots,
baby marrows, etc.) put it in the inlet cylinder placed on the handle. Turn on the
machine and help the cutting by pressing slightly on the pusher handle or with the
pestle if you use the inlet cylinder.
2. When the product is cut, lift the pusher handle, a safety device will stop the
machine. Load another product and lower the handle, the machine will start
automatically.
3. To replace the disc and change the type of cutting, proceed as described in Disc
Assembly. After this operation, an electronic device will lock the automatic restart
of the machine; to restart the machine, it will be necessary to press push button
“I”.
4. If you use the bowl, after 2-3 cutting cycles, empty it. The use of the machine
with a full bowl, could block the discharge of the product in the working area, and
cause a faulty cut, the machine lock or the motor failure.

13
Maintenance
DISCS
With time the blade could wear:
• For DTV, DT 2, 3, 4, 7, 9 and PS 6, 8, 10, 20 discs; it is necessary to buy new discs.
• For DF 1, 2, 3, 4, 5, 8, 10, 14 and DQ 4, 6, 8, 10 discs, it is possible to replace the blade.
In this case, call Omcan indicating the name of the disc.
TROUBLESHOOTING
The xing of the discs is faulty: Check that the discs and the disc support pin are clean.
The lid does not lock: Check that the lid is installed correctly and that it is clean.
The product is not cut correctly: Check that the blade is not worn.
The product does not go out correctly or is badly cut: Check that the discharging spatula has not been
assembled with the DT discs (the whole set); DF 1, 2, 3, 4; DQ 4; that the bowl is not full and that the exit
opening is not obstructed.
The machine locks: Check that the product is not frozen or too hard and that the power supply is the one
indicated on the rating plate.
The micro on the pusher handle and on the lid do not work: Check that they are not dirty.
The machine does not start: Check that all the safety devices are correctly installed and that the plug and the
switches are correctly connected.
CLEANING OF THE MACHINE
IMPORTANT
• The machine must be cleaned at least once a day. If necessary clean when required during the day.
• All the Vegetable cutter parts that come into contact directly or indirectly with the food product must be
cleaned thoroughly.
Before starting cleaning operations, it is necessary to:
• Disconnect the machine plug from the mains to isolate it from the mains power supply.
Pay attention to hazards of injury caused by cutting and/or sharp machine components during
cleaning or handling of discs.
CLEANING PRODUCTS - CAUTION!
The machine must be cleaned with a normal detergent at ambient temperature, with a wet cloth. It must never
be cleaned with pressurised water, or water jets, do not use brushes or other tools or anything that could
damage the machine.
NOTE: NEVER WASH THE MACHINE PARTS IN THE DISHWASHER.
IMPORTANT: Disconnect the machine from the power supply. Remove the lid and the discs, the
spatula, the pestle, the bowl and/or the chute. Clean accurately the inside of the mouth, the operating
area and the disc support pin. Moreover clean all the external surfaces and the pusher handle. Dry with
a cloth and reassemble the machine.

14
Maintenance
SCRAPPING
PUTTING THE MACHINE OUT OF SERVICE
If for some reason, you decide to put the machine out of service, make sure nobody can use it:
• Disconnect it from the mains and eliminate electrical connections.
SCRAPPING
When the machine is out of service,
it can be disposed of. To scrap the
machine contact your local Specialised
Waste Treatment Centre, separate
components.
REFERENCE
Item Number Model Number Description Manufacturer Model Number
10927 FP-IT-0300 Food Processor 300 RPM
0.7 HP / 522 W 110V/60/1 ETL cETLus TM

15
Parts Breakdown
Model FP-IT-0300 10927

16
Parts Breakdown
Model FP-IT-0300 10927

17
Parts Breakdown
Model FP-IT-0300 10927
Item No. Description Position Item No. Description Position Item No. Description Position
16491 Aluminum Lid for TM 2 19260 Closing Knob for TM 42 37338 Insert for TM 104
37314 Pin 5X30 for TM 4 37325 Stainless Steel Prong Shoulder Screw
for TM 46 19258 Retaining C-Clip Ext.Seeger D20 for TM 108
16490 Magnet 6X12 for TM 6 37326 Stainless Steel Cabinet with Louvers
for TM 50 19257 Retaining C-Clip Seeger D42 for TM 110
37315 Pin for Aluminum Lid for TM 7 37327 Motor 110/60 UL for TM 52 37339 US Power Cord 110V for TM 200
16503 Product Pusher Knob for TM 8 37328 Screw for TM 54 37340 Terminal Box for TM 202
16493 Pusher Complete for TM 10 37329 Base / Frame for TM 60 37341 Power Connection Cable for TM 206
37316 Nylon Spacer for TM 12 37348 Nut M 08 for TM 62, 234 16492 Microswitch Spring for TM 209, 216
37317 Stainless Steel Lever for TM 14 37330 Washer 6X18 for TM 66 16487 Supporto Micro 1 UL for TM 210
37318 Plug for TM 16 16496 Foot M8 for TM 70 16485 Micro Plunger-Long UL for TM 211, 214
16486 Pusher Housing UL for TM 20 37331 Belt Pulley for TM 80 37342 Cylinder X Pin Micro UL for TM 213
37319 Acorn Nut M 08 for TM 26 16481 Belt J 483X8 for TM 82 37343 Square Support Micro ETL UL for TM 215
37320 Washer 08X24 INOX for TM 28 19259 Bearing 6004 2RS for TM 84, 112 24106 Microswitch UL for TM 219, 220
24107 Stud Bolt M8 for TM 30 37332 Bearing Block for TM 90 37344 Microswitch Wiring for TM 224
16455 Ejector for TM 32 37333 Washer 06X24 for TM 94 16452 On/Off Switch Weber 120 V for TM 228
37321 Nylon Pivot Stop-Block for TM 33 37334 Motor Pulley for TM 96 37345 Bottom Enclosure Panel for TM 230
37322 Screw T.E. INC 4X16 for TM 34 37335 Main Shaft Assembly D.20 for TM 100 16498 Capacitor 35 MF for TM 240
37323 Screw TEI 4X10 for TM 35 37336 Set Pin 6X6X20 for TM 102 37346 Protection Cover for TM 246
37324 Square Hopper for TM 40 37337 Set Screw M 04X05 for TM 103 37347 Product Container 1/3 H.200 for TM 260

18
Electrical Schematics
Model FP-IT-0300 10927

19
Warranty Registration
Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,
cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:
Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la
carte au niveau de la perforation, puis l’envoyer à l’adresse spécié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:
Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at
the perforation and then send to the address specied below. You can also register online by visiting:
OMCAN
PRODUCT WARRANTY REGISTRATION
3115 Pepper Mill Court,
Mississauga, Ontario
Canada, L5L 4X5
www.omcan.com/warrantyregistration.html
or email to: [email protected]
Purchaser’s Information
Name: Company Name:
Address:
Telephone:
City: Province or State: Postal or Zip: Email Address:
Country: Type of Company:
Restaurant Bakery Deli
Dealer from which Purchased: Butcher Supermarket Caterer
Dealer City: Dealer Province or State: Institution (specify):
Invoice: Other (specify):
Model Name: Model Number: Serial Number:
Machine Description:
Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):
Would you like to extend the warranty? Yes No

Por correo en Canadá
Pour postale au Canada
For mailing in Canada
Por correo en los EE.UU.
Pour diffusion aux États-Unis
For mailing in the US
OMCAN
PRODUCT WARRANTY REGISTRATION
4450 Witmer Industrial Estates, Unit 4,
Niagara Falls, New York
USA, 14305
Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan

Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North
American food service industry. Our success over these many years can be attributed to our commitment
to strengthen and develop new and existing relationships with our valued customers and manufacturers.
Today with partners in North America, Europe, Asia and South America, we continually work to improve
and grow the company. We strive to offer customers exceptional value through our qualied local sales
and service representatives who provide convenient access to over 3,500 globally sourced products.
Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et
matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces
nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles
et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en
Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et
développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à
nos ventes locales qualiées et des représentants de service qui offrent un accès facile à plus de 3500
produits provenant du monde entier.
Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros
de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir
a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos
clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan
continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor
excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un
fácil acceso a más de 3,500 productos con origen a nivel mundial.