Omega CNiS16D User manual

a
d
dd d
a
aaa
a
aaaaaaa
d
a
Below is a flowchart showing how to navigate through all
top level menus by pressing the dand a buttons.
_____Underline denotes factory default setup
FLOW CHART
DISPLA COLOR SETUP (examples)
Example 1:
Output 1 & Output 2: SSR
larm setup: bsolute, bove, larm 2 HI Value
" LR.H" =200, larm 1 HI Value " LR.H"=400
Color Display setup: Normal Color "N.CLR"=Green, larm 1
Color "1.CLR"= mber, larm 2 Color "2.CLR"=Red
Display colors change sequences:
GREEN | RED | AMBER
•-➤----------------•-----------------------•--------------------------------➤
0 L2.H=200 L1.H=400
Example 2:
Output 1: Relay, Set Point 1 = 200,
Output 2: Relay, Set Point 2 = 200
larm 1 setup: Deviation, Band, " LR.H" = 20
larm 2 setup: Deviation, Hi/Low, " LR.H = 10", " LR.L = 5"
Color Display setup: "N.CLR"=Green, "1.CLR"= mber,
"2.CLR"=Red
Display colors change sequences:
AMBER | RED | GREEN | GREEN |RED | AMBER
•-➤--------•----------•--------------•--------------•----------•------------➤
0 180 195 200 210 220
READING CONFIGURATION SETUP
(operation example)
Below is a flowchart showing how to navigate through the
submenus of the Reading Configuration menu item by
pressing the front buttons.
d dbb
• • •
ddb
dbb
d dbb
• • •
dbd
ddd
bc d
ddd
dddd
• • • • • • • •
a
a
a
bc
bcbc
bcbc
MQS3538/1204
†Where:
C LC/V LUE = Calculated input based on
the transducer specification
[Without Known Loads (DSBL)]
CT/V LUE = ctual signal being received
[Known Loads (ENBL)]
†
SPECIFICATION
Accuracy: 0.03% rdg.
Resolution: 10 / 1 µV process
Linearization Points: 10 Points
Temperature Stability:
50 ppm/°C
Display: 4-digit, 9-segment LED,
10.2 mm (0.40") with red, green
and amber programmable colors
Input Types:
nalog Voltage and Current
Voltage: 0 to 100 mV,
0 to 1V (+100 mV),
0 to 10Vdc
Input Impedance:
10 MΩ for 100 mV
,
1 MΩ for 1 or 10 Vdc
Current: 0 to 20 m (5 Ω load)
Output 1:
Relay 250 Vac @ 3 Resistive
Load, SSR, Pulse, nalog
Voltage and Current
Output 2:
Relay 250 Vac @ 3
Resistive Load, SSR, Pulse
Options: Communication
RS-232/RS-485 or 10Base T
or
Excitation: 5 Vdc @40m ,
10 Vdc @ 60 m
Exc. not available for Low Power Option
Line Voltage/Power:
90 - 240 Vac ±10%, 50 - 400 Hz*,
or 110-375 Vdc, 4W single display;
5W dual display
* No CE compliance above 60 Hz
Low Voltage Power Option:
12 - 36Vdc, 3 W** single display;
20 - 36Vdc, 4 W** dual display;
**Units can be powered safely with 24 ac
but No Certification for CE/UL are claimed.
Dimensions:
48 H x 48 W x 127 D mm
(1.89 x 1.89 x 5")
Weight: 159 g (0.35 lb)
Approvals:
UL, C-UL, CE per EN61010-1
:2001 CNiS16 / CNiS16D
Process / Strain Gauge
Controller
USA
MADE IN
Servicing North America:
USA: One Omega Drive, P.O. Box 4047
ISO 9001 Certified Stamford CT 06907-0047
TEL: [phone] F X: [phone]
e-mail: [email protected]
Canada: 976 Bergar
Laval (Quebec) H7L 5 1
TEL: [phone] F X: [phone]
e-mail: [email protected]
For immediate technical or application assistance:
USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEG ®
Customer Service: 1-800-622-2378 / 1-800-622-BEST®
Engineering Service: 1-800-872-9436 / 1-800-US -WHEN
®
Mexico and TEL: (001)800-TC-OMEG ® F X: [phone]-78
0
Latin American: En Español: [phone]-7803
e-mail: [email protected]
Servicing Europe:
Benelux: Postbus 8034, 1180 L mstelveen, The Netherlands
TEL: [phone] F X: [phone]
Toll Free in Benelux: 0800 0993344
e-mail: [email protected]
Czech Republic: Frystatska 184, 733 01 Karviná
TEL: [phone] F X: [phone]
e-mail: [email protected]
France: 11, rue Jacques Cartier, 78280 Guyancourt
TEL: [phone] F X: [phone]
Toll Free in France: 0800 466 342
e-mail: [email protected]
Germany/Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
TEL: [phone] F X: [phone]
9
Toll Free in Germany: 0800 639 7678
e-mail: [email protected]
United Kingdom: One Omega Drive
ISO 9002 Certified River Bend Technology Centre
Northbank, Irlam Manchester M44 5BD United Kingdom
TEL: [phone] F X: [phone]
Toll Free in England: 0800 488 488
e-mail: [email protected]
OMEGAnet® On-Line Service
www.omega.com
Internet e-mail
[email protected]
®
®
WARRANTY/DIS LAIMER
OMEG ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of
one (1) year from the date of purchase. In addition to OMEG ’s standard warranty period, OMEG Engineering will
extend the warranty period for four (4) additional years if the warranty card enclosed with each instrument is
returned to OMEG .
If the unit malfunctions, it must be returned to the factory for evaluation. OMEG ’s Customer Service Department will
issue an uthorized Return ( R) number immediately upon phone or written request. Upon examination by OMEG ,
if the unit is found to be defective, it will be repaired or replaced at no charge. OMEG ’s W RR NTY does not apply
to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing,
operation outside of design limits, improper repair, or unauthorized modification. This W RR NTY is VOID if the unit
shows evidence of having been tampered with or shows evidence of having been damaged as a result of excessive
corrosion; or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating
conditions outside of OMEG ’s control. Components which wear are not warranted, including but not limited to
contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither
assumes responsibility for any omissions or errors nor assumes liability for any damages that result from
the use of its products in accordance with information provided by OMEGA, either verbal or written. OMEGA
warrants only that the parts manufactured by it will be as specified and free of defects. OMEGA MAKES NO
OTHER WARRANTIES OR REPRESENTATIONS OF AN KIND WHATSOEVER, EXPRESS OR IMPLIED,
EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING AN WARRANT OF
MERCHANTABILIT AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREB DISCLAIMED. LIMITATION
OF LIABILIT : The remedies of purchaser set forth herein are exclusive, and the total liability of OMEGA with
respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or
otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event
shall OMEGA be liable for consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEG is not intended to be used, nor shall it be used: (1) as a “Basic
Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications
or used on humans. Should any Product(s) be used in or with any nuclear installation or activity, medical application,
used on humans, or misused in any way, OMEG assumes no responsibility as set forth in our basic
W RR NTY/DISCL IMER language, and, additionally, purchaser will indemnify OMEG and hold OMEG harmless
from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.
RETURN REQUESTS/INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEG Customer Service Department. BEFORE
RETURNING NY PRODUCT(S) TO OMEG , PURCH SER MUST OBT IN N UTHORIZED RETURN ( R)
NUMBER FROM OMEG ’S CUSTOMER SERVICE DEP RTMENT (IN ORDER TO VOID PROCESSING
DEL YS). The assigned R number should then be marked on the outside of the return package and on any
correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in
transit.
FOR W RR NTY RETURNS, please have the
following information available BEFORE
contacting OMEG :
1. Purchase Order number under which the product
was PURCH SED,
2. Model and serial number of the product under
warranty, and
3. Repair instructions and/or specific problems
relative to the product.
FOR NON-W RR NTY REP IRS, consult OMEG for
current repair charges. Have the following information
available BEFORE contacting OMEG :
1. Purchase Order number to cover the COST of the
repair,
2. Model and serial number of product, and
3. Repair instructions and/or specific problems
relative to the product.
OMEG ’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords
our customers the latest in technology and engineering.
OMEG is a registered trademark of OMEG ENGINEERING, INC.
© Copyright 2004 OMEG ENGINEERING, INC. ll rights reserved. This document may not be copied, photocopied,
reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without
the prior written consent of OMEG ENGINEERING, INC.
P TENT ND TR DEM RK NOTICE: This product is covered by one or more of the following patents: U.S. Pat.
No. Des. 336,895; 5,274,577; 6,243,021 / C N D 2052599; 2052600 / IT LY 1249456; 1250938 / GERM NY DE
41 34398 C2 / SP IN 2039150; 2048066 / UK Patent No. GB2 249 837; GB2 248 954 / FR NCE BREVET NO. 91
12756. The “Meter Bezel Design” is a trademark of Newport Electronics, Inc. USED UNDER LICENSE. Other U.S.
and International Patents pending or applied for.
This device is marked with the international caution symbol. It is important to read the
Setup Guide before installing or commissioning this device, as the guide contains important
information relating to safety and EMC.
WARNING: These products are not designed for use in, and should not be used for, patient-
connected applications.
It is the policy of OMEG to comply with all worldwide safety and EMC/EMI regulations that apply.
OEMG is constantly pursuing certification of its products to the European New pproach Directives.
OMEG will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct, but OMEG Engineering, Inc.
accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.
TRADEMARK NOTI E:
®,omega.com®,, and ®are Trademarks of
OMEG ENGINEERING, INC.
®

Disassembly Instruction:
If necessary, the unit may be removed from the panel and
opened.
Warning: Disconnect all ac power from the unit
before proceeding.
1. Remove all wiring connections from the rear of the meter.
To remove connector assembly, squeeze top and
bottom of the case near the connector site for release,
then pull connectors from case.
2. To remove meter from the case, squeeze top and bottom
of the bezel to release, then pull from case.
WIRING
Wire the instrument according to the figure shown below.
Warning: Do not connect ac power to your
device until you have completed all input and
output connections. This device must only be
installed by a specially trained electrician with
corresponding qualifications. Failure to follow all
instructions and warnings may result in injury!
This Quick Start Reference provides information
on setting up your instrument for basic operation.
The latest complete Communication and Operational
Manual as well as free Software and ctiveX Controls
are available at www.omega.com/specs/iseries or
on the CD-ROM enclosed with your shipment.
SAFET CONSIDERATION
This device is marked with the international
Caution symbol.
The instrument is a panel mount device protected in
accordance with EN61010-1:2001. Remember that the unit
has no power-on switch. Building installation should include
a switch or circuit-breaker that must be compliant to IEC
947-1 and 947-3.
SAFET :
• Do not exceed voltage rating on the label located on
the top of the instrument housing.
• lways disconnect power before changing signal and
power connections.
• Do not use this instrument on a work bench without
its case for safety reasons.
• Do not operate this instrument in flammable or
explosive atmospheres.
• Do not expose this instrument to rain or moisture.
EMC:
• Whenever EMC is an issue, always use shielded cables.
• Never run signal and power wires in the same conduit.
• Use signal wire connections with twisted-pair cables.
• Install Ferrite Bead(s) on signal wire close to the
instrument if EMC problems persist.
MOUNTING
Panel Mounting Instruction:
1. Using the dimensions from the panel cutout diagram
shown above, cut an opening in the panel.
2. Insert the unit into the opening from the front of the panel,
so the gasket seals between the bezel and the front of the
panel.
3. Slide the retainer over the rear of the case and tighten
against the backside of the mounting panel.
START HERE
Connect the main power connections in the figure shown below.
FUSE Connector Output Type For 115Vac For 230Vac DC
FUSE 1 Output 1 Relay 3 (T) 3 (T) -
FUSE 2 Output 2 Relay 3 (T) 3 (T) -
FUSE 3 Power N/ 100 m (T) 100 m (T) 100 m (T)
FUSE 4 Power N/ N/ N/ 400 m (T)
CONFIGURATION
Button Functions in Configuration Mode
• To enter the Menu, the user must first press a
button.
• Use this button to advance/navigate to the next
menu item. The user can navigate through all the
top level menus by pressing a.
• While a parameter is being modified, press ato
escape without saving the parameter.
• Press the up bbutton to scroll through “flashing”
selections. When a numerical value is displayed
press this key to increase value of a parameter
that is currently being modified.
• Holding the bbutton down for approximately
3 seconds will speed up the rate at which the
setpoint value is incremented.
• In the Run Mode pressing bcauses the display to
flash the PE K or GROSS value – press again to
return to the Run Mode.
• Press the down cbutton to go back to a previous
Top Level Menu item.
• Press this button twice to reset the controller to
the Run Mode.
• When a numerical value is flashing (except
setpoint value) press cto scroll digits from left to
right allowing the user to select the desired digit to
modify.
• When a setpoint value is displayed press cto
decrease value of a setpoint that is currently being
modified. Holding the cbutton down for
approximately 3 seconds will speed up the rate at
which the setpoint value is decremented.
• In the Run Mode pressing ccauses the display to
flash T RE value to tare your reading (zeroing).
• Press the enter dbutton to access the submenus
from a Top Level Menu item.
• Press dto store a submenu selection or after
entering a value — the display will flash a STRD
message to confirm your selection.
• To reset flashing PE K or GROSS press d.
• In the Run Mode, press dtwice to enable
Standby Mode with flashing STBY.
123 456 78
Reset: Except for larms, modifying any settings of
the menu configuration will reset the controller prior
to resuming Run Mode.
DISPLA ABBREVIATIONS
SP1 Set Point 1 Value SP2 Set Point 2 Value
CNFG Configuration Menu INPt Input Type (Range)
INPt Input Type (range) 0 - 0.1 100 mV Input
Voltage
0 - 1.0 1 V Input Voltage 0 - 10 10 V Input Voltage
0 - 20 20 m Input Current
Rtio Ratiometric Operation RESO Display Resolution
bUtN Button Peak/Gross PEAk Peak Value
GROS Gross Value
RdG Reading Configuration
dEC Decimal Point F.FFF Decimal Point
..FFFF Position
LOAd Input Load EnbL Scaling with Known
Loads ( ctual Value)
DSbL Scaling without Known L.PNt Linearization Points
Loads (Calculated Value)
0002.. Number of Linearization FLtR Filter Constant
..0010 Points
0001.. Filter Constant Value IN.Rd Input/Reading Scale
..0128 and Offset Menu
IN 1 Input 1 Rd 1 Reading 1
IN 2 Input 2 Rd 2 Reading 2
... ... ... ...
IN 10 Input 10 Rd 10 Reading 10
ANLG nalog Output CURR Current Output
VoLt Voltage Output Rd 1 Reading 1
Out.1 Output 1 Rd 2 Reading 2
Out.2 Output 2
ALR1 larm 1 Menu AbSo bsolute Mode
_dEV Deviation Mode LtcH Latched Mode
UNLt Unlatched Mode Ct.CL Contact Closure
N.o. Normally Open N.c. Normally Closed
ActV ctive Type AboV ctive bove
bELo ctive Below Hi.Lo bove High/Below
Low
bANd bove or Below Band A.P.oN larm Enable/Disable
at Power On
ALR.L larm Low Value ALR.H larm High Value
ALR.2 larm 2 Menu
LOOP Loop Break Menu b.tIM Loop Break Time
R.AdJ Reading djust SP.dN Set Point Deviation
OUt1 Output 1 Menu SELF Manual Control
ººLO Percent Low ººHI Percent High
CtRL Control Type ON.OF On/Off Control
4 -20 mplitude Control PId PID Control
ActN ction Type RVRS Reverse ction
dRct Direct ction ANt1 nti Integral
AUto uto PID A.tUN uto Tune PID
StRt Start uto Tune PID PRoP Proportional Band
RESt Reset Setup RAtE Rate Setup
C CL Cycle Time dPNG Damping Factor
dEAd Dead Band
OUt2 Output 2 Menu
RAMP Ramp Time SOAk Soak Time
Id ID Code Menu CH.Id Change ID Code
FULL Full ID SP.Id Set Point ID
COMM Communication Option* NONE Communication is
Not Installed
COLR Display Color Selection N.CLR Normal Color Display
1.CLR larm 1 Color Display 2.CLR larm 2 Color
Display
REd Display Color is Red AMbR Display Color is
mber
GRN Display Color is Green
dSbL Disable ENbL Enable
ERRO Error + OL Input (+) Overload
* For abbreviations of Communication Option see Communication Manual.
a
d
c
b
PK/GRS
(UP)
MENU
TARE
(DOWN)
ENTER
If instrument has the
communication option,
the internal excitation
is not available. Use
external excitation to
power your transducer.
See Specification Section
2
1
2
1