Russound BSK-2 User manual

BSK-2
Bluetooth Source Kit
INSTALLATION GUIDE

2Russound BTC-2X Installation Guide
OVERVIEW
Thank you for purchasing the BSK-2 Bluetooth Source Kit from Russound. Since 1967, Russound has been providing
audio professionals with the tools they need to enhance the lives of their customers. The BSK-2 can be used in
multiple ways:
• To provide multiple Bluetooth inputs to a Russound controller in the same installation
• To allow a Bluetooth radio to be located up to 500’ (165m) from connected audio gear, allowing for the ultimate
in Bluetooth range in any home or business.
The BSK-2 is a complete kit composed of the BTC-2X Bluetooth Remote Transceiver and the BTC-2 Termination Box.
Russound sells the BTC-2X separately for standalone applications where the extended range is not needed, or when
the BTC-2X is to be used as the only Bluetooth device used with a Russound MCA-Series controller.
With its advanced Bluetooth 5.1 technology, the BSK-2 is the perfect solution for your Bluetooth audio needs.
GETTING TO KNOW YOUR BTCX
BTC-2X
TO BTC-2 or MCA
POWER PAIR
AUDIO
OUT
REMOTE PAIR
5V 2A

 
: 














Serial Number
MAC ID
MicroUSB Power
Connection
Source Number Switch (Only used
when connected to a Russound
MCA-Series Controller)
Connect to
MCA-Series
Controller
Pairing Button 3.5mm Stereo
Audio Out
Pairing Mode Switch
MAC ID Label
Keyhole Mounting
Slots
Remote Pairing
Contact Closure

Russound BTC-2X Installation Guide 3
USING YOUR BSK BLUETOOTH SOURCE KIT
The BSK-2 is a unique Bluetooth solution that allows audio connections to be made at an amplier or receiver while
locating the Bluetooth radio (found in the BTC-2X) up to 500’ (152m)away in the area of the home closer to a user’s
phone or tablet that is being used as the Bluetooth audio source.
Input Saver Feature
The BSK-2 oers a helpful input saver design. With many of today’s audio devices reducing the number of dedicated
inputs, the BSK-2 allows you to add Bluetooth to any system without requiring a new input connection. The input saver
allows you to connect any audio source and have it be the primary audio source until Bluetooth is activated. Whenever
a Bluetooth audio signal is detected, the audio content will automatically switch to Bluetooth. When the Bluetooth
signal stops, the audio content will automatically switch back to the other source.
GETTING TO KNOW YOUR BTC
MicroUSB Power
Connection
RCA Analog Stereo
Input (For Input
Saver Feature)
BTC-2X
Connection
RNET Connections for
connection to a Russound
MCA-Series Controller
(Optional)
RCA Analog Stereo
Output
Digital Audio Output
BTC-2
POWER
AUDIO IN
TO BTC-2X
R L
AUDIO OUT OPTICAL OUT
R L
IN OUT
5V 2A5V 2A5V 2A
OPERATION

4Russound BTC-2X Installation Guide
This means that the BSK-2 is ideal for use directly with stereo or multi-channel ampliers and can be connected even if
all inputs on the amplier are already in use.
POWER CONNECTION
Use the included MicroUSB power cable and the included 5VDC power supply to supply power to the BTC-2. The
power supply includes adaptor plates for US, UK, Euro, and AUS power sockets. To change the adaptor, simply press
the button marked “Push” to release the plate and, after aligning the new adaptor plate properly, simply snap it into
place until it clicks.
Please note that both the BTC-2 and the BTC-2X have a MicroUSB power input. When used together, power is
supplied to the BTC-2 and the only connection needed on the BTC-2X is a CAT-5 cable that will carry power, data, and
audio signals up to 500’ (152m).
OPERATION
BTC-2
POWER
AUDIO IN
TO BTC-2X
R L
AUDIO OU T OPTICAL OUT
R L
IN OUT
5V 2A5V 2A5V 2A
BTC-2X
TO BTC-2 or MCA
POWER PAIR
AUDIO
OUT
REMOTE PAIR
5V 2A
CAT5 up to 500’
RCA Audio
RCA Audio
BTC-2X
BTC-2
MicroUSB
Power
Supply
Russound Amplifier with other source inputs used
CD Player

Russound BTC-2X Installation Guide 5
PAIRING MODE
The BTC-2X has two pairing modes: automatic and manual, which are set via a convenient slide switch on the bottom
of the BTC-2X.
Automatic Pairing
Automatic Pairing is the simplest method and is designed for use in most residential single-family homes or any envi-
ronment where it is not likely to have any neighbors or other people close enough to pair their phones or tablets to the
BTC-2X. When not connected to a phone or tablet, the BTC-2X will always be available to pair with any new device
within range that requests pairing.
Manual Pairing
Manual Pairing is designed for all applications when greater control over the Bluetooth connections is desired and
especially in environments where multiple homes are within Bluetooth range such as Multi-Dwelling Units (MDU’s) like
condominiums, townhouses, apartments, etc.
When in manual pairing mode, the BTC-2X will only be able to pair with new phones or tablets when not connected to
a device and someone:
a) Presses the “Pair” button on the rear panel of the BTC-2X; - OR 
b) Activates the “Remote Pair” contact closure on the rear panel of the BTC-2X. The Remote Pair is a unique
optional feature that allows an installation professional to wire a simple push button control or to use an
automated contact closure from a smart home control system. This allows the BTC-2X to be hidden com-
pletely from sight and still be able to be put into pairing mode easily when desired.
OPERATION

6Russound BTC-2X Installation Guide
NAMING YOUR BTCX
A convenient feature of the BTC-2X is the ability to re-name it to a “friendly” name that makes it easier to access and
use in your home. The default name of the BTC-2X is “BTC-2X-ZZZZ” with “ZZZZ” being the last four digits of the
device’s MAC ID.
After installing your BTC-2X using one of the conguration options listed below, you can easily rename it to something
more convenient. For example, if you install the BTC-2X in your Living Room, you can rename it to “Living Room” so
that it is easier to identify on your phone or tablet’s list of available Bluetooth devices.
To rename your BTC-2X
1) Download and install the Russound BTC-2X Naming App from either the App Store or the Google Play Store.
2) With the BTC-2X powered up, within Bluetooth range, and already paired to your phone, open the BTC-2X
Naming App.
3) The app should automatically discover all Russound BTC-2X devices within range. You can refresh the
screen by swiping down in the app.
4) Once your BTC-2X is discovered, select it and tap “Connect”. Once connected, you can enter a new Blue-
tooth name and tap “Enter”.
5) Your BTC-2X has now been congured with the new name.
Note: Names can be up to 15 characters long and composed of any mix of letters from A-Z, Numbers 0-9 and the “-“
character. To avoid confusion, we recommend using a dierent name from all other Bluetooth devices in the home.
Audio Connections with the BSK-2 Kit
The BSK-2 Kit has two components, the BTC-2X Bluetooth Remote Transceiver and the BTC-2 Termination Box. The
BTC-2 should be located near your audio equipment and the BTC-2X in the area of the home where the Bluetooth
audio source is going to be used. A CAT-5 cable is used to connect the two. The CAT-5 cable carries data, power, and
the audio signal between the two.
OPERATION

Russound BTC-2X Installation Guide 7
Audio output from the BTC-2 can be either analog stereo RCA or optical digital. You are free to use either one depend-
ing on your preference or the availability of inputs on your amplier or receiver.
From the BTC-2, simply connect either the RCA analog stereo outputs to your amplier or receiver or connect the Tos-
link Digital Optical connection depending on your available inputs on your amplier or receiver (cables not included).
USING YOUR BTCX WITH A RUSSOUND MCASERIES CONTROLLER
The BSK-2 Bluetooth Source Kit can be used when adding more than one Bluetooth source to a Russound MCA-Series
Controller. All of the connections are made as listed above, but several additional steps are necessary:
Setting the Source Number
Before using the BTC-2X with a Russound MCA-66 or MCA-88, the source number switch on the bottom of the BTC-
2X must be properly set to the same source number that is congured in the MCA-Series controller’s WebCong.
Set the rotary dial on the bottom of the BTC-2X to correspond with the same source number to be used on the MCA-
66 or MCA-88 controller. Make sure that the MCA-Series controller’s associated source type is congured with the
Source Type of “BTC-2X”.
Connecting to the Controller
Use a CAT-5 cable to connect one of the RNET ports on the back of the BTC-2 to an open RNET port on the rear of the
MCA-Series controller.
When adding more than one BSK-2 kits, continue connecting from an open RNET port on the additional BTC-2 to an
open RNET port on the controller or on a previously connected BTC-2. In other words, the BTC-2 boxes must be daisy
chained together and then to the controller.
USING WITH A MCASERIES CONTROLLER

8Russound BTC-2X Installation Guide
CONNECTING MULTIPLE BTCX/BTC PRODUCTS WITH A MCASERIES CONTROLLER
Make sure to adjust the “Source Number” rotary dial on the bottom of each BTC-2X to correspond with the source
number being used for the audio input on the Russound controller and to congure the same audio source in the con-
troller’s Web Cong as a “BTC-2X”.
MCA-88 Controller
BTC-2X
TO BTC-2 or MCA
POWER PAIR
AUDIO
OUT
REMOTE PAIR
5V 2A
BTC-2X
TO BTC-2 or MCA
POWER PAIR
AUDIO
OUT
REMOTE PAIR
5V 2A
BTC-2
POWER
AUDIO IN
TO BTC-2X
R L
AUDIO OUT OPTICAL OUT
R L
IN OUT
5V 2A5V 2A5V 2A
BTC-2X
TO BTC-2 or MCA
POWER PAIR
AUDIO
OUT
REMOTE PAIR
5V 2A
BTC-2
POWER
AUDIO IN
TO BTC-2X
R L
AUDIO OUT OPTICAL OUT
R L
IN OUT
5V 2A5V 2A5V 2A
MicroUSB
Power
Supply
MicroUSB
Power
Supply

Russound BTC-2X Installation Guide 9
Metadata with the BTC-2X
When connected to a Russound MCA-Series controller (MCA-66 or MCA-88), the BTC-2X can provide metadata
such as song titles, album name, etc that is visible on compatible Russound keypads, touchscreens or when using the
Russound app. This metadata is available for any BTC-2X connected to the controller’s Bluetooth input port as well
as for any BTC-2X connected with the BTC-2 Termination Box that is connected to the controller using an RNET cable
connection as mentioned previously.
Source Control with the BTC-2X
As with the metadata, the same BTC-2X devices can also receive control commands from the Russound controller us-
ing either connected keypads, touchscreens, or the Russound app. Use these to pause, resume play, skip forward and
back, etc. on any compatible Bluetooth audio source devices.

10 Russound BTC-2X Installation Guide
BTC SPECIFICATIONS
Connections
RJ-45, 3.5mm Audio Out, Remote Pairing
RJ-45, Stereo RCA Input/Output, Toslink
Digital Output, Remote Pairing
Max CAT-5/6 Cable Length to BTC-2X from
Russound Controller 500' (152m)
Audio Out RCA Stereo Analog and Toslink Digital
Optical
Power Requirements
BTC-2 Termination Hub 5VDC microUSB (110-220VAC Power Supply
Included)
Dimensions (L x W x H) 6.5” (16.51 cm) x 4.6” (11.7cm) x 1” (2.54 cm)
Weight 0.8 lbs (0.36 kg)
SPECIFICATIONS

Russound BTC-2X Installation Guide 11
BTCX SPECIFICATIONS
Bluetooth Version 5.1
Range* Indoors - Up to 65' (20m)
Outdoors - Up to 195’ (60m)
Connections RJ-45, 3.5mm Audio Out, Remote Pairing
Pairing Modes Automatic, Manual, and Contact Closure
Max CAT5 Cable Length to BTC-2X from Russound
Controller 500' (152m)
Audio Out 3.5mm Analog Stereo Out (Cable Not Includ-
ed)
Power Requirements
Standalone Operation 5VDC microUSB (110-220VAC Power Supply
Included)
Working with BTC-2 or MCA Controller Power Supplied by BTC-2 or MCA Controller
via CAT5/6 Cable Connection (Not Included)
Dimensions (L x W x H) 3.375" (8.6 cm) x 2.25" (5.7 cm) x 1.13" (2.9 cm)
Weight 0.3 lbs (.14 kg)

©2022 Russound/FMP, Inc. All rights reserved.
All trademarks are the property of their respective owners.
Specications are subject to change without notice 08.14.22 REV3
LIMITED WARRANTY
The Russound BSK-2 is guaranteed for two (2) years from
the date of purchase against all defects in materials and
workmanship. During this period Russound will replace any
defective parts and correct any defect in workmanship without
charge for either parts or labor. For this warranty to apply, the unit
must be installed and used according to its written instructions.
If service is necessary, it must be performed by Russound.
Russound assumes no responsibility for defects resulting
from abuse or servicing performed by an agency or person
not specically authorized in writing by Russound. Damage to
or destruction of components due to improper use voids the
warranty. In these cases, the repair will be made at the owner’s
expense. Accidental damage and shipping damage are not
considered defects under the terms of the warranty. To return for
repairs, the unit must be shipped to a repair facility designated
by Russound at the owner’s expense, along with a Return
Authorization number and documentation explaining the nature
of the service required. Any product returned without
prior written permission will be returned to sender. Russound
sells products only through authorized Dealers and Distributors
to ensure that customers obtain proper support and service.
Any Russound product purchased from an unauthorized dealer
or other source, including retailers, mail order sellers and online
sellers will not be honored or serviced under existing Russound
warranty policy. Any sale of products by an unauthorized source
or other manner not authorized by Russound shall void the
warranty on the applicable product.
WARRANTY ADDRESS
Russound
Attn: RA# (Insert your RA number here)
1955 Wehrle Dr
Williamsville NY 14221
email: t[email protected]om