Omega OM-CP-QUADVOLT User manual

OM-CP-QUADVOLT
4-Channel Low Level DC Voltage Data Logger
OM-CP-OCTVOLT
8-Channel Low Level DC Voltage Data Logger
MQS5086/1216
Xxxxx Xxxxxx
Xxxxx Xxxxxx Xxxxxxxx
M0000/0016
INSTRUCTION
SHEET
Xxxxx Xxxxxx
Xxxxx Xxxxxx Xxxxxxxx
M0000/0016
INSTRUCTION
SHEET
Shop online at omega.comSM e-mail: [email protected]
For latest product manuals: www.omegamanual.info
Office: Jl. Radin Inten II No. 62 Duren Sawit, Jakarta 13440 - Indonesia
Workshop: Jl. Pahlawan Revolusi No. 22B, Jakarta 13430 - Indonesia
Phone: [phone] (Hunting) Fax: [phone]
Mobile: [phone]
Fax: [phone]

Product Overview
Engineering Units
Engineering units are used to convert one measurement reading to another. The OM-CP Data Logger software
allows for software level Engineering Units (conversion applied to data after download). Certain devices have
device level Engineering Units, which upon download automatically appear in the chosen unit of measure.
Wiring the Data Logger
OM-CP-QUADVOLT and OM-CP-OCTVOLT Single Ended Wiring (2.5, 15 and 30V)
Two-position removable screw terminal connections; accepts 2-wire configurations.
OM-CP-QUADVOLT and OM-CP-OCTVOLT Differential Wiring (+-100mV)
Three-position removable screw terminal connections; accepts 3-wire configurations.
Warning: Note the polarity instructions. Do not attach wires to the wrong terminals.
OM-CP-QUADVOLT and OM-CP-OCTVOLT
Office: Jl. Radin Inten II No. 62 Duren Sawit, Jakarta 13440 - Indonesia
Workshop: Jl. Pahlawan Revolusi No. 22B, Jakarta 13430 - Indonesia
Phone: [phone] (Hunting) Fax: [phone]
Mobile: [phone]
Fax: [phone]

Installation Guide
Installing the Interface Cable
- OM-CP-IFC200
Insert the device into a USB port. The drivers will install automatically.
- OM-CP-IFC110
Plug the serial cable into the port and verify it is secure.
Installing the software
Insert the Omega Software Flash Drive in an open USB port. If the autorun does not appear, locate the drive
on the computer and double click on Autorun.exe. Follow the instructions provided in the Wizard.
Device Operation
Connecting and Starting the data logger
- Once the software is installed and running, plug the interface cable into the data logger.
- Connect the USB end of the interface cable into an open USB port on the computer.
- The device will appear in the Connected Devices list, highlight the desired data logger.
- For most applications, select “Custom Start” from the menu bar and choose the desired start method,
reading rate and other parameters appropriate for the data logging application and click “Start”. (“Quick
Start” applies the most recent custom start options, “Batch Start” is used for managing multiple loggers at once,
“Real Time Start” stores the dataset as it records while connected to the logger.)
- The status of the device will change to “Running”, “Waiting to Start” or “Waiting to Manual Start”,
depending upon your start method.
- Disconnect the data logger from the interface cable and place it in the environment to measure.
Note: The device will stop recording data when the end of memory is reached or the device is stopped. At this point
the device cannot be restarted until it has been re-armed by the computer.
Downloading data from a data logger
- Highlight the data logger in the Connected Devices list. Click “Stop” on the menu bar.
- Once the data logger is stopped, with the logger highlighted, click “Download”. You will be prompted to
name your report.
- Downloading will offload and save all the recorded data to the PC.
OM-CP-QUADVOLT and OM-CP-OCTVOLT

Device Maintenance
Battery Replacement
Materials: 3/32” HEX Driver (Allen Key) and Replacement Battery (OM-CP-BAT103)
- Remove the cover from the device by unscrewing the four screws.
- Remove the battery from its compartment and unsnap it from the connector.
- Snap the new battery into the terminals and verify it is secure.
- Replace the cover taking care not to pinch the wires. Screw the enclosure back together securely.
Note: Be sure not to over tighten the screws or strip the threads.
Recalibration
The OM-CP-QUADVOLT or OM-CP-OCTVOLT standard calibration is dependant upon the range.
Recalibration is recommended annually for any Omega data logger; a reminder is automatically displayed in
the software when the device is due. Specifications subject to change. See Omega’s terms and conditions at
www.omega.com
OM-CP-QUADVOLT and OM-CP-OCTVOLT
Range 100mV 2.5V 15V 30V
Calibration Point 0mV and
90-100mV
0mV and
2.25-2.5V
0mV and
14.9-15.5V
0mV and
27-30V

Description OM-CP-QUADVOLT
Voltage Range
*See Table BelowVoltage Resolution
Voltage Accuracy
Memory 32,767/channel
Reading Rate 1 reading every second up to 1 reading every 12 hours
LED Indicator None
Channels 4
Required Interface Package IFC110 or IFC200
Baud Rate 2,400
Typical Battery Life 1 year
Operating Environment -40°C to +60°C, 0%RH to 95%RH (non–condensing)
Material Anodized aluminum
Dimensions 3.5” x 4.4” x 1.0”
(89 mm x 112 mm x 26 mm)
Weight 13 oz (370 g)
OM-CP-QUADVOLT General Specifications
Battery Warning
WARNING: FIRE, EXPLOSION, AND SEVERE BURN HAZARD. DO NOT SHORT CIRCUIT, CHARGE, FORCE OVER DISCHARGE, DISASSEMBLE, CRUSH,
PENETRATE OR INCINERATE. BATTERY MAY LEAK OR EXPLODE IF HEATED ABOVE 60°C (140°F).
Specifications subject to change.
See Omega’s terms and conditions at www.omega.com
Still need help? For more troubleshooting tips and information, refer to the built in help section visit us online at www.omega.com
or contact us for support at 1 [phone].
*OM-CP-QUADVOLT Range, Resolution and Calibrated Accuracy
Nominal Range +-100mV 0 to 2.5V 0 to 15V 0 to 30V
Measurement Range (VDC) +-150mV -0.25 to 2.75 -1 to 16 -2 to 32
Accuracy +-0.01%FSR +-0.01%FSR +-0.10%FSR +-0.10%FSR
Resolution (mV) 5µV 0.1 0.5 1.0
Common Mode Input Range 0 to 2.5V 0 to 2.5V 0 to 2.5V 0 to 2.5V
OM-CP-QUADVOLT and OM-CP-OCTVOLT

OM-CP-QUADVOLT and OM-CP-OCTVOLT
OM-CP-OCTVOLT General Specifications
Description OM-CP-OCTVOLT
Voltage Range
*See Table BelowVoltage Resolution
Voltage Accuracy
Memory 16,383/channel
Reading Rate 1 reading every second up to 1 reading every 12 hours
LED Indicator None
Channels 8
Required Interface Package IFC110 or IFC200
Baud Rate 2,400
Typical Battery Life 1 year
Operating Environment -40°C to +60°C, 0%RH to 95%RH (non–condensing)
Material Anodized aluminum
Dimensions 3.5 in x 4.4 in x 1.5 in
(89 mm x 112 mm x 39 mm)
Weight 17 oz (480 g)
Battery Warning
WARNING: FIRE, EXPLOSION, AND SEVERE BURN HAZARD. DO NOT SHORT CIRCUIT, CHARGE, FORCE OVER DISCHARGE, DISASSEMBLE, CRUSH,
PENETRATE OR INCINERATE. BATTERY MAY LEAK OR EXPLODE IF HEATED ABOVE 60°C (140°F).
*OM-CP-OCTVOLT Range, Resolution and Calibrated Accuracy
Nominal Range +-100mV 0 to 2.5V 0 to 15V 0 to 30V
Measurement Range (VDC) +-150mV -0.25 to 2.75 -1 to 16 -2 to 32
Accuracy +-0.01%FSR +-0.01%FSR +-0.10%FSR +-0.10%FSR
Resolution (mV) 5µV 0.1 0.5 1.0
Common Mode Input Range 0 to 2.5V 0 to 2.5V 0 to 2.5V 0 to 2.5V
Office: Jl. Radin Inten II No. 62 Duren Sawit, Jakarta 13440 - Indonesia
Workshop: Jl. Pahlawan Revolusi No. 22B, Jakarta 13430 - Indonesia
Phone: [phone] (Hunting) Fax: [phone]
Mobile: [phone]
Fax: [phone]