Omega PHH-1X Litmustik User manual

applications buffer 7.0 should be used. solution. For most
!t IS recommended that the unit be calibrated in buffer equipment. pH* As with all
pH) could be due to dry electrode or
run-down batteries. To improve performance, leave PHH-1X up to
immersion level
in tap water for a few minutes at least once a week.
To change batteries, pull out the battery case and replace batteries. Refer to
Figure 2.
When not in use, switch off the instrument. To ensure optimum operation,
electrode should be kept moist. If soaker pad in bottom of protective
cap is dry,
pour buffer 7.0 or 4.0 into cap to remoisten pad. If pad is missing simply add
buffer 7.0 or 4.0 to cap. Replace protective cap.
(+0.5 pH
pH value to the sample to
be measured, by adjusting the CALIBRATION TRIMMER located on the reverse
side. Refer to the calibration instructions.
Dip PHH-1X in solution up to immersion level. Under no circumstances immerse
above immersion level. Refer to Figure 1.
Stir gently and wait a few seconds.
Large differences in readings of
pH buffer solution, close in
pH bulb is dry.
Calibrate the PHH-1X in a
pH units and
offers better accuracy than test paper ’.
OPERATING PROCEDURE
1.
2.
3.
4.
5.
6.
7.
8.
9.
Remove the black protective cap.
Turn on the PHH-1X with the ON/OFF switch located on top.
Condition the PHH-1X according to the conditioning instructions. Large error can
occur if the
pH range from 0 to 14
pH tester features large display numerics for easy
reading, and single point calibration. Designed for fast evaluations in the field, this
high performance tester measures the entire
Litmustik@ is an economical handheld unit small enough to fit
in a pocket. This newly designed
M1008/0592
GENERAL DESCRIPTION
The OMEGA PHH-1X
pH Tester
LITMUSTIK” PHH-1X

*-_
i
part for any purpose whatsoever without written permission
from OMEGA ENGINEERING. INC. Printed in U.S.A.
QCopyright 1992 OMEGA ENGINEERING. INC. All rights reserved including illustrations. Nothing in this manual
may be reproduced in any manner. either wholly or in
LI registered trademark of OMEGA ENGINEERING, INC.
way
our customers get the latest in technology and engineering.
OMEGA is
an improvement is possible. That
-FTURN (AR) FROM OUR CUSTOMER SERVICE DEPARTMENT. Please
have the following information available BEFORE contacting OMEGA:
1. P.O. number under which the product was PURCHASED,
2. Model and serial number of product, and
3. Repair instructions and/or specific problems you are having
with the product.
OMEGA’s policy is to make running changes, not model changes, whenever
A’-‘TI-I@ AN OBTAIN YQ.W!dUST
203-359-1660,FAX: [phone].
BEFORE RETURNING ANY PRODUCT(S) TO OMEGA,
Canada:l-800-622-2378, FAX: 203-359-
7811; International:
/ INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA ENGINEERING Customer
Service Department. Call toll free in the USA and
[phone]
RETURN REQUESTS
6XR, England
Telephone: [phone] FAX:
LE9
[phone] TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA
OMEGA Technologies Ltd.
P.O. Box 1, Broughton Astley, Leicestershire
l-800-USA-WHEN
FAX:
/ l-800-622-BEST Engineering: l-800-872-9436
/
l-800-TC-OMEGA
Customer Service: l-800-622-2378
I
[phone]
Sales: l-800-826-6342
x 0.6 ” D
WEIGHT:
0.13 lb.; 2.1 ounces
OMEGA Engineering, Inc.
One Omega Drive, Box 4047, Stamford, CT 06907-0047 U.S.A.
Headquarters:
V battery
DIMENSIONS:
5.9” L x 1.3 ” W
x 1.5 4
50°c
BATTERY LIFE:
1000 hours of continuous use,
pH
OPERATING TEMPERATURE: 0 to
pH units from standardization point
RESOLUTION:
0.1
+_3 pH, +_0.2
Litmustik@ is
designed for single point calibration only. For accurate measurements, periodic
recalibration is recommended.
SPECIFICATIONS
RANGE:
Oto 14pH
ACCURACY:
pH pen must be calibrated in a buffer solution close to the
value of the sample to be measured. Calibration is performed by turning the
CALIBRATION TRIMMER on the reverse side of the tester. The
pH
electrode is allowed to dry out. If unit is properly stored, this procedure is not
necessary.
CALIBRATION OF THE PHH-1X
After conditioning, the
X
Soak the sensing tip in either buffer 4, buffer 7, KCL solution or tap water for at least
30 minutes. Make sure that the sensing tip is immersed up to at least one inch from
the tip. This procedure should be followed when unit is received or if the
PHH-1 Ut- I HtIUNlNCi CIUIYUI I