2
ID Description Qty
1Shelf 1
2Shelf Pegs 2
3Foot Assembly 2
4Leg Assembly 2
5Extended Leg 2
6Spacer 2
7Lock Nut 2
8Support Screw 2
9Hex Wrench 1
10 Rubber Pad 4
The CCH-1 has been designed to fit on the widest possible range of TV’s. Assembly and installation of the CCH-1 will vary, de-
pending upon your TV type: CRT TV or DLP/LCD Projection TV. Proceed to the section related to your TV type.
A—Shallow Back
Thread Foot Assemblies (3) into Spacers (6). (Fig. 3)
Attach Foot Assemblies to position 2on Shelf with Support Screws (8).
(Fig 4)
CCH-1
Fig. 3
Installing on CRT TV
First, determine your chassis style:
A—Shallow Back (Fig 1)
B—Steep Back (Fig 2).
Fig. 1 Fig. 2
B—Steep Back
Extend Leg from Leg Assembly (4) using Hex Wrench (9). Thread Foot Assem-
bly (3) into Leg Assembly(4). (Fig 7).
Attach Leg Assemblies to position 2on Shelf with Support Screws (8). (Fig 8)
Fig. 7
Remove backing strip Rubber Pads (10), and press onto bottom of Foot Assembly (3) and front edge of
Shelf. (Fig. 5)
Thread Shelf Pegs (2) into holes on front edge of Shelf (1). (Fig. 5)
Place CCH1 on top of TV, with Shelf Pegs overlapping front edge of TV, as
shown in Fig. 6.
Thread Foot Assembly In or Out of Spacer until Shelf sits level.
Note: Maximum foot extension is shown in Fig 6.
Tighten Lock Nut (7) against leg to hold level position.
Proceed to section titled Mounting Components to CCH-1.
Fig. 5
Fig. 8
Fig. 4
Fig. 6
3
Remove backing strip Rubber Pads (10), and press onto bottom of Foot Assembly and front edge of Shelf.
(Fig. 9)
Thread Shelf Pegs (2) into holes on front edge of Shelf (1). (Fig. 9)
Fig. 9
Place CCH1 on top of TV, with Shelf Pegs overlapping front edge of TV, as shown in Fig. 10.
Loosen hex screw and slide Leg In or Out until Shelf sits level, then
secure Leg in position with hex wrench.
Note: Maximum extension is shown in Fig 10.
For additional minor adjustments, thread Foot Assembly In or Out of
Leg until Shelf sits level. Tighten Lock Nut (7) against leg to hold
level position.
Proceed to section titled Mounting Components to CCH-1.
Installing on DLP/LCD Projection TV
First, determine your chassis style:
C—Shallow Back (Fig 11)
D—Steep Back (Fig 12).
C—Shallow Back
Extend Leg from Leg Assembly (4) using Hex Wrench (9). Thread
Foot Assembly (3) into Leg Assembly(4). (Fig 13).
Attach Leg Assemblies to position 1on Shelf with Support Screws
(8). (Fig 14)
Fig. 13
Remove backing strip Rubber Pads (10), and press onto bottom of Foot Assembly and front edge of Shelf.
Thread Shelf Pegs (2) into holes on front edge of Shelf (1). (Fig. 15)
Place CCH1 on top of TV, with Shelf Pegs overlapping front edge of
TV, as shown in Fig. 16.
Loosen hex screw and slide Leg In or Out until Shelf sits level, then
secure Leg in position with hex wrench.
Note: Maximum extension is shown in Fig 16.
For additional minor adjustments, thread Foot Assembly In or Out of Leg until Shelf sits
level. Tighten Lock Nut (7) against leg to hold level position.
Proceed to section titled Mounting Components to CCH-1.
D—Steep Back
Remove Leg from Leg Assembly (4) using Hex Wrench (9). Install Ex-
tended Leg (5) into Leg Assembly (4) using Hex Wrench (9). Thread
Foot Assembly (3) into Leg Assembly(4). (Fig 17).
Attach Leg Assemblies to position 1on Shelf with Support Screws (8).
(Fig 18)
Fig. 14
Fig. 11 Fig. 12
Fig. 15
Fig. 17
Fig. 18
Fig. 10
Fig. 16
