Omnitron Systems Technology miConverter 10/100 Plus User manual

Page 2 Page 3
Page 6
Page 4
Page 5 Page 7 Page 8
WARNING!
Before inserting the Power Adapter, verify
that the power on the unit is appropriate
for your AC line voltage source.
POWER MODES
AC power adapter is available in US, Universal and
Country/Region specific models. Country/Region
specific models feature optional interchangeable
connectors, allowing for compatibility with electrical
outlet types found around the world.
This product should only be used with Omnitron
Supplied Power Unit.
To power the module using the USB cable, connect the
USB Standard Type A connector to a USB port on the
computer. Then connect the connector at the other end
of the cable (barrel connector) to the connector on the
back of the miConverter. Conrm that the module has
powered up properly by checking the power status LED
located on the top of the module.
To power the module using the AC/DC adapter, connect
the AC/DC adapter to the AC outlet. Then connect the
barrel connector at the end of the cable to the back of
the miConverter. Conrm that the module has powered
up properly by checking the power status LED located
on the top of the module.
DESCRIPTION
The miConverter™10/100 Plus is a 10/100BASE-T
copper to 100BASE-FX ber media converter. The UTP
copper port can automatically detect the speed, duplex
mode and crossover mode of the connected device, or it
can be manually congured via DIP-switches.
The 100BASE-FX ber port operates in Full-Duplex
mode and supports single-mode or multimode ber with
ST or SC ber connectors. Single-mode models feature
Bi-Directional ber and support distances of up to 40km.
The various ber models options are described in the
table on the rst page.
Several Link Modes (fault-detection capabilities) are
available with the 10/100 Plus, including Link Segment
(Normal Mode), Link Propagate (Link Loss Carry
Forward), Remote Fault Detection and Symmetrical
Fault Detection. The link mode assist in the identication
and isolation of link failures.
POWERING OPTIONS
-1 Barrel Connector and US Power Adapter,100 - 120VAC, 60Hz
-2 Barrel Connector and Universal Power Adapter,
100-240VAC, 50-60Hz (requires AC power cord)
-3 Barrel Connector and European Power Adapter,
100-240VAC, 50-60Hz
-4 Barrel Connector and UK Power Adapter,
100-240VAC, 50-60Hz
-5 Barrel Connector and Australian Power Adapter,
100-240VAC, 50-60Hz
-6 USB Power Adapter Cable
-8 Barrel Connector and US/Japan Power Adapter,
100-240VAC, 50-60Hz
miConverter™10/100 Plus
Media Converter
User Manual
INSTALLATION PROCEDURE
The miConverter 10/100 can be quick-mounted using
the included Velcro®strips, or permanently mounted
using the optional wall-mounting kit (P/N 4381).
Configure the miConverter 10/100 Plus with the
appropriate DIP-switch settings. The factory default
conguration for the UTP copper port is “AN” Auto-
negotiation and the Link Mode is “LS” Link Segment.
Attach the RJ-45 port of the miConverter 10/100 to
a 10BASE-T or 100BASE-TX PoE capable Ethernet
device, via a category 5 or better cable.
Attach the ber port of the miConverter 10/100 to a
100BASE-X Fast Ethernet device, via a ber cable of
appropriate mode and type.
When connecting the dual-ber models, the miConverter
transmitter (Tx) must attach to the receiver side of its link
partner; the receiver (Rx) must attach to the transmitter.
When using single-ber (SF) media converter models,
the Tx wavelength on one end has to match the Rx
wavelength on the other. Based on this guideline, the
SF media converter models must be used in pairs, such
as the 1130-1 matched with the 1131-1.
DIP-SWITCH SETTINGS
AN Auto (default)
MAN 10MbpsHD
MAN 100MbpsFD
LS (default)
LP
MAN 100MbpsHD
UTP ModeLink Mode
Figure 1: DIP-switch Congurations
UTP Mode Selection
The UTP port is congured using the DIP-switches as
shown in Figure 1. There are four modes of operation
based on the position of the DIP-switches. The factory
default conguration is “AN” Auto-negotiation. In the
“AN” mode, the port will advertise 100Mbps Full-Duplex,
100Mbps Half-Duplex, 10Mbps Full-Duplex and 10Mbps
Half-Duplex.
The UTP port can be congured for Manual negotiation
by setting the appropriate DIP-switches. The port can
be congured for 100Mbps Full-Duplex, 100Mbps Half-
Duplex and 10Mbps Half-Duplex.
Link Mode Selection
The miConverter 10/100 Plus can be congured for
several miConverter Link Modes. The DIP-switch
illustration in Figure 1 indicates how to congure the
different Link Modes.
Link Segment (LS)
“LS” (factory default) generates and detects a link signal
at each point in the network. Utilizing this conguration,
a loss of a receive link signal will only affect the port
detecting the loss of signal. All the other ports will
continue to generate a link signal. Figure 2(A) indicates
the normal operation of the system without faults. Figure
2(B) indicates a loss of a receive link on the ber optic
port, the UTP port continues to maintain its link.
Switch 1 Converter A Converter B Switch 2
LP
LP
Switch 1 Converter A Converter B Switch 2
LS LS
(B)
(C)
Switch 1 Converter A Converter B Switch 2
Fiber
UTP
UTP
UTP
UTP
Fiber
(A)
Normal Operation
Figure 2a, 2b and 2c: Link Modes
Link Propagate (LP)
“LP” generates (transmits) a link signal only when a link
signal is detected. Utilizing this conguration, a loss of
a receive link signal will continue to ‘propagate’ through
to the next port in the network. In Figure 2(C), a loss
of a receive link on the ber optic port causes the UTP
port to drop its link due to the propagated ber optic link
state. This setting allows the loss of a link to be detected
by SNMP or other managed network devices to which
the miConverter 10/100 Plus is connected.
NOTE: Only the rst loss of a receive link detected by
the miConverter 10/100 Plus turns off the other port’s
transmit link. An additional loss of a receive link on
the other port has no affect on the miConverter 10/100
Plus. The miConverter 10/100 Plus returns to normal
operation when the rst loss of a receive link is restored.
Remote Fault Detect + Link Segment (RFD + LS)
“RFD+LS” generates a link signal only when a link signal
is detected. However, instead of propagating the fault
forward, the loss of link is looped back. In Figure 2(D),
a loss of a received link state is looped back causing the
port to stop transmitted the link state. Because the other
unit is congured for Link Propagate, the UTP port will
drop its link due to the propagated ber optic link state.
NOTE: It is not permitted to set both Converter A and B
to RFD at the same time; a deadly embrace will occur.
Page 1
Fiber
Type
and
Distance
Connector Types Tx
Lambda
(nm)
Rx
Lambda
(nm)
ST SC
MM/DF/5km 1120-0-x 1122-0-x 1310 1310
SM/DF/30km 1121-1-x 1123-1-x 1310 1310
SM/DF/60km 1121-2-x 1123-2-x 1310 1310
SM/DF/120km - 1123-3-x 1550 1550
MM/SF/5km - 1130-0-x 1310 1550
MM/SF/5km - 1131-0-x 1550 1310
SM/SF/20km - 1130-1-x 1310 1550
SM/SF/20km - 1131-1-x 1550 1310
SM/SF/40km - 1130-2-x 1310 1550
SM/SF/40km - 1131-2-x 1550 1310
SM/SF/60km - 1130-3-x 1310 1550
SM/SF/60km - 1131-3-x 1550 1310
Symmetrical Fault Detect (SFD)
“SFD” generates a Link Loss signal on all ports on both
media converters when a loss of link signal is detected
by one of the ports. In Figure 2(E), the pattern of LEDs
gives an indication of the failure point.
NOTE: Both media converters must be congured with
the SFD Link Mode. The SFD function is only supported
by Omnitron Systems equipment.
Switch 1 Converter A Converter B Switch 2
LP RFD+LS
(D)
RFD
Switch 1 Converter A Converter B Switch 2
SFD SFD
(E)
RFD
LED ON LED OFFLED
LED Flashing LED ON or OFF
- LED status depends on the link
type; AN - OFF, MAN - ON
Figure 2d and 2e: Link Modes

Page 15
Page 10 Page 11 Page 12
Page 9
Page 14 Page 16
SPECIFICATIONS:
Form: 040-11200 -001E 3/18
General and Copyright Notice
This publication is protected by U.S. and international
copyright laws. All rights reserved. The whole or
any part of this publication may not be reproduced,
stored in a retrieval system, translated, transcribed,
or transmitted, in any form, or by any means, manual,
electric, electronic, electromagnetic, mechanical,
chemical, optical or otherwise, without prior explicit
written permission of Omnitron Systems Technology,
Inc.
The following trademarks are owned by Omnitron
Systems Technology, Inc.: FlexPointTM, HybridNID®,
iConverter®, miConverterTM, NetOutlook®, OmniLightTM,
OmniConverterTM, Omnitron Systems Technology, Inc.
TM, OSTTM and the Omnitron logo.
All other company or product names may be
trademarks of their respective owners.
The information contained in this publication is
subject to change without notice. Omnitron Systems
Technology, Inc. is not responsible for any inadvertent
errors.
Warranty
This product is warranted to the original purchaser
against defects in material and workmanship for a
period of two (2) years from the date of shipment. A
LIFETIME warranty may be obtained by the original
purchaser by registering this product within ninety
(90) days from the date of shipment at www.omnitron-
systems.com/support. During the warranty period,
Omnitron will, at its option, repair or replace a product
which is proven to be defective with the same product
or with a product with at least the same functionality.
For warranty service, the product must be sent to
an Omnitron designated facility, at Buyer’s expense.
Omnitron will pay the shipping charge to return the
product to Buyer’s designated US address using
Omnitron’s standard shipping method.
TECHNICAL SUPPORT:
For help with this product, contact Omnitron’s Tech.
Support:
Phone: [phone]
Fax: [phone]
Address: Omnitron Systems Technology, Inc.
38 Tesla
Irvine, CA 92618 USA
E-mail: [email protected]
URL: http://www.omnitron-systems.com
SPECIFICATIONS (CONT.):
Page 13
LED INDICATORS:
LED Function
“Legend”
Color
Off On
Power
“Pwr”
Amber
No power Power applied
Fiber Link
“F/O”
Green
No ber link ON: Fiber link
Blinking (10Hz): Data activity
Blinking (5Hz): SFD Error
RJ-45 Link
“UTP”
Green
No UTP link ON: UTP link
Blinking (10Hz): Data activity
Blinking (5Hz): SFD Error
RJ-45 Speed
“100”
Green
Linked at 10M
when UTP LED
is ON
ON: Linked at 100M when
UTP LED is ON
RJ-45 Duplex
“FDX”
Green
Half Duplex ON: Full Duplex
Standard
Compliances IEEE 802.3
Regulatory
Compliances* UL, CE, FCC Class A, RoHS2 (6/6), REACH, WEEE
Frame Size Up to 1,536 bytes
Port Types Copper:
Fiber:
10/100BASE-T (RJ-45)
100BASE-X (ST, SC)
Cable Types
Copper:
Fiber:
EIA/TIA 568A/B, Cat 5 UTP and higher
Multimode: 50/125µm, 62.5/125µm
Single-mode: 9/125µm
AC Power
Requirements
US AC Adapter: 100 - 120VAC/60Hz
0.03A @ 120VAC (max)
Universal AC
Adapter:
100 - 240VAC/50 - 60Hz
0.03A @ 120VAC (max)
DC Power
Requirements
DC Input:
(AC Adapter)
5.0 to 15.0VDC
0.5A @ 5VDC, 0.28A @ 9VDC
2.5mm Barrel Connector
Dimensions
Standalone: W: 1.71” x D: 4.10” x H: 0.84”
L: 43.4 mm x B: 104.1 mm x H: 21.3 mm
Weight
Without AC
Adapter:
With AC adapter:
4 oz. (113.4 grams)
12 oz. (340.2 grams)
Temperature Commercial:
Wide:
0 to 50°C
-40 to 60°C
Humidity 5 to 95% (non-condensing)
Altitude -100m to 4,000m
MTBF (hrs)
Without AC
Adapter:
With US AC
Adapter:
1,160,000
206,000
Warranty Lifetime warranty with 24/7/365 free Technical Support
Limitation of Warranty
The foregoing warranty shall not apply to defects
resulting from improper or inadequate use and/
or maintenance of the equipment by Buyer, Buyer-
supplied equipment, Buyer-supplied interfacing,
unauthorized modications or tampering with
equipment (including removal of equipment cover
by personnel not specically authorized and certied
by Omnitron), or misuse, or operating outside the
environmental specication of the product (including
but not limited to voltage, ambient temperature,
radiation, unusual dust, etc.), or improper site
preparation or maintenance.
No other warranty is expressed or implied. Omnitron
specically disclaims the implied warranties of
merchantability and tness for any particular purpose.
The remedies provided herein are the Buyer’s sole
and exclusive remedies. Omnitron shall not be
liable for any direct, indirect, special, incidental, or
consequential damages, whether based on contract,
tort, or any legal theory.
Environmental Notices
The equipment covered by this manual must be
disposed of in accordance with Directive 2002/96/
EC of the European Parliament and of the council of
27 January 2003 on waste electrical and electronic
equipment (WEEE). Such disposal must follow national
legislation for IT and Telecommunication equipment
in accordance with the WEEE directive: (a) Do not
dispose waste equipment with unsorted municipal
and household waste. (b) Collect equipment waste
separately. (c) Return equipment using collection
method agreed with Omnitron.
The equipment is marked with the WEEE symbol to
indicate that it must be collected separately from other
types of waste. In case of small items the symbol may
be printed only on the packaging or in this manual. If
you have questions regarding the correct disposal of
equipment go to www.omniton-systems.com/support
or e-mail to Omnitron at intlinfo@omnitron-systems.
com.