[nm]
ST SC
MM / DF 5km 1100-0-x 1102-0-x 1310 1310
SM / DF 30km 1101-1-x 1103-1-x 1310 1310
SM / DF 60km 1101-2-x 1103-2-x 1310 1310
SM / DF 120km - 1103-3-x 1550 1550
SM / SF 20km - 1110-1-x 1310 1550
SM / SF 20km - 1111-1-x 1550 1310
SM / SF 40km - 1110-2-x 1310 1550
SM / SF 40km - 1111-2-x 1550 1310
When choosing power options, replace (-x) in the model number with
the suffix number that correspondes to the power supply of choice
below. Example: 1103-3-6 stands for 1103-3-x with USB Power Adapter
-1 US Power Supply - 120Volt / 60Hz
-2 UniversalPower Supply (requires AC power cord) -
100-240Volt / 50-60Hz
-3 Euro Power Supply - 100-240Volt / 50-60Hz
-4 UK Power Supply - 100-240Volt / 50-60Hz
-5 Australia Power Supply- 100-240Volt / 50-60Hz
-6 USB Power Adapter Cable
-8 Japanese Power Supply - 100-240Volt/ 50-60Hz
For power supplies -3, -4, -5 and -8, country/region specific clips are used to
provide the necessarypower connection.
Accessories
Wall Mounting Hardware Kit 4381
USB Power Adapter Cable 9130-2
US Domestic AC Power Adapter 9113-PS
Universal AC Power Adapter
(requires AC power cord) 9115-PS
Europe AC Power Adapter 9116-PS-3
United Kingdom AC Power Adapter 9116-PS-4
Australia AC Power Adapter 9116-PS-5
Japanese AC Power Adapter 9116-PS-8
European Connector Clip* 9116-3
UK Connector Clip* 9116-4
Australian Connector Clip* 9116-5
Japanese Connector Clip* 9116-8
*All spare Connector Clips are interchangeable with AC Power
Adapters 9116-PS-3, 9116-PS-4, 9116-PS-5 and 9116-PS-8
DESCRIPTION:
The miniature miConverter™10/100 is a rate-switching
UTP copper to 100BASE-FX fiber media converter that
provides cost-effective fiber extension and connectivity.
The miConverter 10/100’s UTP copper port can
automatically detect the speed, duplex-mode and
cross-over mode of the connected device.
The100BASE-FX fiberport operatesin Full-Duplexmode
and supports single-mode or multimode fiber with ST or
SC fiber connectors. Single-fiber models feature
Bi-Directional fiber and support distances of up to 40km.
Thevarious fibermodel optionsare describedinthe table
on the first page.
WARNING!
Before inserting the Power Adapter, verify
that the power on the unit is appropriate
for your AC line voltage source.
POWERADAPTER NOTICE:
Thisproduct shouldonlybeusedwithOmnitronSupplied
Power Unit model numbers 9113-PS, 9115-PS, 9130-2,
9116-PS-3,9116-PS-4, 9116-PS-5or 9116-PS-8.
In order to guarantee performance when powering the
miConverter 10/100 with the USB Power Adapter cable
(P/N 9130-2), the USB adapter cable must be connected to
a Full-Powered USB Type-Aport (5V, 500mA).
Note: Not all USB Type-A ports are Full-Powered
USB ports. The Full-Powered USB Type-Aports are
usually the USB ports found on computer cases or
on self-powered (powered by an AC adapter) USB
hubs.
MOUNTINGAND CABLE ATTACHMENT:
The miConverter 10/100 can be quick-mounted using
the included Velcro®strips, or permanentaly mounted
using the optional wall-mounting kit (P/N 4381).
Attach the UTP port of the miConverter 10/100 to a
10BASE-T or 100BASE-TX Ethernet device, via a
category 5 cable.
Attach the fiber port of the miConverter 10/100 to a
100BASE-FX Fast Ethernet device, via the fiber cable
of the appropriate mode and type.
Whenconnecting thedual-fibermodels, themiConverter
transmiter (Tx) must attach to the receiver side of its
link partner; the receiver (Rx) must attach to the
transmiter.
When using single-fiber (SF) media converter models,
the Tx wavelength on one end has to match the Rx
wavelength on the other. Based on this guideline, the
SF media converter models must be used in pairs,
such as the 1110-1-x matched with the 1111-1-x.
LEDINDICATORS:
Function Legend Color Off On
Power Pwr Amber No power Power applied
F/O Link-
Act F/O Green No link Solid = Link
Blink = Data Received
UTP Link-
Act UTP Green No link Solid = Link
Blink = Data Received
00(On) 100 Green UTP at 10Mbps when
UTP Link is active UTP at 100Mbps
when UTP Link is
active
HDX(Off) /
FDX(On) FDX Green Half-Duplex when
UTP Link is active Full-Duplex when UTP
Link is active
Caution
All user-required operations can be performed without
opening the unit. Never attempt to open or remove the
cover or tamper with the unit.
Warranty
This product is warranted to the original purchaser against
defects in material and workmanship for a period of TWO
YEARS from the date of shipment. A LIFETIME warranty
maybeobtainedbytheoriginalpurchaserbyREGISTERING
this product with Omnitron within 90 days from the date of
shipment.TOREGISTER,COMPLETEANDMAILORFAX
THE ENCLOSED REGISTRATION FORM TO THE
INDICATEDADDRESS.Or you mayregister yourproduct
on the internet at http://www.omnitron-systems.com.
Duringthewarranty period,Omnitronwill,atitsoption, repair
or replace a product which is proven to be defective.
Forwarrantyservice,theproductmustbesenttoanOmnitron
designated facility, at Buyer’s expense. Omnitron will pay
the shipping charge to return the product to Buyer’s
designatedUS addressusingOmnitron’sstandardshipping
method. Limitation of Warranty
The foregoing warranty shall not apply to defects
resulting from improper or inadequate use and/or
maintenanceofthe equipmentby Buyer, Buyer-supplied
equipment, Buyer-supplied interfacing, unauthorized
modifications or tampering with equipment (including
removalof equipmentcoverby personnelnot specifically
authorized and certified by Omnitron), or misuse, or
operating outside the environmental specification of the
product (including but not limited to voltage, ambient
temperature, radiation, unusual dust, etc.), or improper
site preparation or maintenance.
No other warranty is expressed or implied. Omnitron
specifically disclaims the implied warranties of
merchantability and fitness for any particular purpose.
Exclusive Remedies
The remedies provided herein are the Buyer’s sole and
exclusive remedies. Omnitron shall not be liable for any
direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal
theory.
SPECIFICATIONS:
miConverter 10/100 Specifications
