OMPHOBBY M1 User manual

M1 FLIGHT
CONTROLLER SETTINGS

DIAGRAM OF FLIGHT CONTROLLER
SERVO
PITCH
SPEED
AGILE
GYRO
RUDD
ELEV
AILE
SET
BIND
S-BUS
CH1
CH2
CH3
DSM/X
GND 5V S5V GND D
LED
-1-
SET
RUDD
ELEV
AILE
SERVO
PITCH
SPEED
AGILE
GYRO
Menu setting button
Rudder setting mode
Elevator setting mode
Aileron setting mode
Servo central point setting
Pitch setting
Rate indicator
Agility indicator
Gyro gain indicator
Note: Bind transmitter to flight controller, wait
for the initialization, then start settings.

Press SET for 3 seconds – RUDD light on – SPEED
light flashes
YAW RATE SETTING
To adjust flight controller settings, press the SET
key for 3 seconds. Click SET key until RUDD
light is on and SPEED light flashes. When the
SPEED light flashes 5 times it indicates factory
default yaw rate. Move the elevator stick up and
down to increase or decrease the yaw rate
setting. The amount of flashes indicates the level,
1 being the lowest to 9 being the highest. After
the desired level is achieved, press the SET key
for 3 seconds to save the setting.
YAW SETTING
-2-
SERVO
PITCH
SPEED
AGILE
GYRO
RUDD
ELEV
AILE
SET
BIND
S-BUS
CH1
CH2
CH3
DSM/X
GND 5V S5V GND D
LED

YAW SETTING
RUDD light on – click SET – GYRO light flashes
YAW GAIN SETTING
To adjust flight controller settings, press the SET
key for 3 seconds. Click SET key until RUDD light
is on and GYRO light flashes. When the GYRO
light flashes 5 times it indicates factory default yaw
gain. Move the elevator stick up and down to
increase or decrease the yaw gain setting. The
amount of flashes indicates the level, 1 being the
lowest to 9 being the highest. After the desired
level is achieved, press the SET key for 3 seconds
to save the setting.
-3-
SERVO
PITCH
SPEED
AGILE
GYRO
RUDD
ELEV
AILE
SET
BIND
S-BUS
CH1
CH2
CH3
DSM/X
GND 5V S5V GND D
LED

www.omphobby.com
OMPHOBBY TM

PITCH SETTING
Press SET 3 seconds – ELEV light on –
SPEED light flashes
PITCH RATE SETTING
To adjust flight controller settings, press the SET
key for 3 seconds. Click SET key until ELEV light
is on and SPEED light flashes. When the SPEED
light flashes 5 times it indicates factory default
pitch rate. Move the elevator stick up and down to
increase or decrease the pitch rate setting. The
amount of flashes indicates the level, 1 being the
lowest to 9 being the highest. After the desired
level is achieved, press the SET key for 3 seconds
to save the setting.
-4-
SERVO
PITCH
SPEED
AGILE
GYRO
RUDD
ELEV
AILE
SET
BIND
S-BUS
CH1
CH2
CH3
DSM/X
GND 5V S5V GND D
LED

PITCH SETTING
ELEV light on – click SET – AGILE light flashes
PITCH AGILITY SETTING
To adjust flight controller settings, press the SET key
for 3 seconds. Click SET key until ELEV light is on
and AGILE light flashes. When the AGILE light
flashes 5 times it indicates factory default pitch agility.
Move the elevator stick up and down to increase or
decrease the agility setting. The amount of flashes
indicates the level, 1 being the lowest to 9 being
the highest. After the desired level is achieved, press
the SET key for 3 seconds to save the setting.
-5-
SERVO
PITCH
SPEED
AGILE
GYRO
RUDD
ELEV
AILE
SET
BIND
S-BUS
CH1
CH2
CH3
DSM/X
GND 5V S5V GND D
LED

PITCH SETTING
ELEV light on – click SET – GYRO light flashes
PITCH GAIN SETTING
To adjust flight controller settings, press the SET key
for 3 seconds. Click SET key until ELEV light is on
and GYRO light flashes. When the GYRO light
flashes 5 times it indicates factory default pitch gain.
Move the elevator stick up and down to increase or
decrease the gain setting. The amount of flashes
indicates the level, 1 being the lowest to 9 being the
highest. After the desired level is achieved, press
the SET key for 3 seconds to save the setting.
-6-
SERVO
PITCH
SPEED
AGILE
GYRO
RUDD
ELEV
AILE
SET
BIND
S-BUS
CH1
CH2
CH3
DSM/X
GND 5V S5V GND D
LED

SERVO
PITCH
SPEED
AGILE
GYRO
RUDD
ELEV
AILE
SET
BIND
S-BUS
CH1
CH2
CH3
DSM/X
GND 5V S5V GND D
LED
AILERON SETTING
Press SET 3 seconds – AILE light on – SPEED light
flashes
AILERON RATE SETTING
To adjust flight controller settings, press the SET key
for 3 seconds. Click SET key until AILE light is on and
SPEED light flashes. When the SPEED light flashes 5
times it indicates factory default aileron rate. Move the
elevator stick up and down to increase or decrease the
rate setting. The amount of flashes indicates the level,
1 being the lowest to 9 being the highest. After the
desired level is achieved, press the SET key for 3
seconds to save the setting.
-7-

-8-
AILERON SETTING
AILE light on – click SET – AGILE light flashes
AILERON AGILITY SETTING
To adjust flight controller settings, press the SET key
for 3 seconds. Click SET key until AILE light is on
and AGILE light flashes. When the AGILE light
flashes 5 times it indicates factory default aileron
agility. Move the elevator stick up and down to
increase or decrease the agility setting. The amount
of flashes indicates the level, 1 being the lowest to 9
being the highest. After the desired level is achieved,
press the SET key for 3 seconds to save the setting.
SERVO
PITCH
SPEED
AGILE
GYRO
RUDD
ELEV
AILE
SET
BIND
S-BUS
CH1
CH2
CH3
DSM/X
GND 5V S5V GND D
LED

AILERON SETTING
AILE light on – click SET – GYRO light flashes
AILERON GAIN SETTING
To adjust flight controller settings, press the SET key
for 3 seconds. Click SET key until AILE light is on and
GYRO light flashes. When the GYRO light flashes 5
times it indicates factory default aileron gain. Move the
elevator stick up and down to increase or decrease the
gain setting. The amount of flashes indicates the level,
1 being the lowest to 9 being the highest. After the
desired level is achieved, press the SET key for 3
seconds to save the setting.
-9-
SERVO
PITCH
SPEED
AGILE
GYRO
RUDD
ELEV
AILE
SET
BIND
S-BUS
CH1
CH2
CH3
DSM/X
GND 5V S5V GND D
LED

SERVO MID-POINT SETTING
SERVO MID-POINT SETTING
SERVO MID-POINT SETTING
To adjust flight controller settings, press the SET key
for 3 seconds. Click SET key until SERVO light is on.
Use the sticks of aileron, elevator, and rudder to
setup the mid-point of the servos. CH1 is for aileron,
CH2 for elevator, and CH3 for rudder. After desired
mid-point is achieved, press SET key for 3 seconds
to save the setting.
-10-
SERVO
PITCH
SPEED
AGILE
GYRO
RUDD
ELEV
AILE
SET
BIND
S-BUS
CH1
CH2
CH3
DSM/X
GND 5V S5V GND D
LED

-11-
Transmitter description
OMPHOBBY
Remote Control Power Light (Red)
IDLE
D/R
HOLD
Remote Control Power Light (Blue)
70%
85%
100%
Attitude mode
3D mode
Attitude mode
Throttle,
Orientation
Helicopter
Battery Indicator
Front,Back,
Left,Right
C OLLECTIVE PITCH SETTING

Click SET – PITCH light on
COLLECTIVE PITH SETTING
COLLECTIVE PITCH SETTING
SET
SERVO
PITCH
SPEED
AGILE
GYRO
RUDD
ELEV
AILE
POWER
-12-
To adjust flight controller settings, press the SET
key for 3 seconds. Click SET key until PITCH light
is on. Toggle the hold switch of radio transmitter to
activate the throttle-cut. Begin by moving the
throttle stick to 50% mid-point and using a pitch
gauge ensure a reading of zero. Then move the
throttle stick to the highest position, use the
elevator stick to increase or decrease the angle of
pitch to your desired setting. Move the throttle
stick to the lowest position, use the elevator stick
to increase or decrease the angle of pitch to your
desired setting. The default factory settings are
12.5 degrees on both ends. After your desired
setting is achieved, press SET key for 3 seconds
to save the setting.

Click SET 10 times
RESET DEFAULT SETTINGS
-13-
SERVO
PITCH
SPEED
AGILE
GYRO
RUDD
ELEV
AILE
SET
BIND
S-BUS
CH1
CH2
CH3
DSM/X
GND 5V S5V GND D
LED
RESET DEFAULT SETTING
After a radio is bound to the helicopter, click SET
key ten times, the blue and red LED lights of the
flight controller will flash at the same time. Reset
is done after the initialization of flight control.

DIAGRAM OF FLIGHT CONTROL
SETTINGS
blue light lighting
-13-