Omron C200HS Series Parts list manual

Programmable Controller C200HS-series
Replacement Guide
From C200HS to CJ2
C200HS-CPU0□
C200HS-CPU2□
C200HS-CPU3□
CJ2H-CPU6□
CJ2M-CPU1□
CJ2M-CPU3□
P074-E1-04

About this document
This document provides the reference information for replacing C200H PLC systems with CS1 series PLC.
This document does not include precautions and reminders ;please read and understand the important precautions
and reminders described on the manuals of PLCs (both of PLC used in the existing system and PLC you will use to
replace the existing PLC) before attempting to start operation.
Company names and product names in this document are the trademarks or registered trademarks of their
respective companies.

Related Manuals
CPU Units
Man.No.
Model
Manual
W472 CJ2H-CPU6□-EIP
CJ2H-CPU6□
CJ2-CPU□□
CJ2 CPU Unit Hardware USER'S MANUAL
W473 CJ2H-CPU6□-EIP
CJ2H-CPU6□
CJ2M-CPU□□
CJ2 CPU Unit Software USER'S MANUAL
W486
CJ2M-CPU□□+CH2M-MD21□
CJ2M Pulse I/O Module USER'S MANUAL
W474 CS1G/H-CPU□□H
CS1G/H-CPU□□-V1
CS1D-CPU□□H
CS1D-CPU□□S
CJ1H-CPU□□H-R
CJ1G/H-CPU□□H
CJ1G-CPU□□P
CJ1M/G-CPU□□
NSJ□-□□□□(B)-□□□
CS/CJ/NSJ Series INSTRUCTIONS REFERENCE MANUAL
W342 CS1G/H-CPU□□H
CS1G/H-CPU□□-V1
CS1D-CPU□□H
CS1D-CPU□□S
CS1W-SCU□□-V1
CS1W-SCB□□-V1
CJ1H-CPU□□H-R
CJ1G/H-CPU□□H
CJ1G-CPU□□P
CJ1M/G-CPU□□
CJ1W-SCU□□-V1
CP1H-X□□□□-□
CP1H-XA□□□□-□
CP1H-Y□□□□-□
NSJ□-□□□□(B)-□□□
CS/CJ/CP/NSJ Series Communications Commands REFERENCE MANUAL
W341 CQM1H-PRO01
CQM1-PRO01
C200H-PRO27
CS1W-KS001
CS/CJ Series Programming Consoles OPERATION MANUAL
W302 C200HX/HG/HE
-CPU□□/CPU□□-Z
SYSMACαINSTALLATION GUIDE
W303
C200HX/HG/HE
SYSMAC
α
OPERATION MANUAL
W322 C200HX-CPU□□-ZE
C200HG-CPU□□-ZE
C200HE-CPU□□-ZE
SYSMACαOPERATION MANUAL

Special I/O Units
Man.No.
Model
Manual
W368
CS1W-PTS□□ CS1W-PTW□□
CS1W-PDC□□
CS1W-PTR□□
CS1W-PPS□□
CS1W-PMV□□
CJ1W-PTS□□
CJ1W-PDC□□
CJ1W-PH41U
CS/CJ Series Analog I/O Units OPERATION MANUAL
W345
CS1W-AD0□□-V1/-AD161 CS1W-DA0□□
CS1W-MAD44
CJ1W-AD0□□-V1/-AD042
CJ1W-DA0□□/-DA042V
CJ1W-MAD42
CS/CJ Series Analog I/O Units OPERATION MANUAL
W396
CJ1W-TC□□□
CJ Series Temperature Control Units OPERATION MANUAL
W401
CJ1W-CT021
CJ Series High-speed Counter Units OPERATION MANUAL
W397
CJ1W-NC□□3
CJ Series Position Control Units OPERATION MANUAL
W477
CJ1W-NC□□4
CJ Series Position Control Units OPERATION MANUAL
W426 CS1W-NC□71
CJ1W-NC□71(-MA)
CS/CJ Series Position Control Units OPERATION MANUAL
W435 CS1W-MCH71
CJ1W-MCH71
CS/CJ series Motion Control Units OPERATION MANUAL
W336
CS1W-SCB□□-V1 CS1W-SCU□□-V1
CJ1W-SCU□□-V1
CS/CJ Series Serial Communications Boards Serial Communications Units
OPERATION MANUAL
W440 CS1W-FLN22
CJ1W-FLN22(100BASE-TX) CS/CJ Series FL-net Units OPERATION MANUAL
V236 CS1W-SPU01
CS1W-SPU02-V2
CJ1W-SPU01-V2
CS/CJ Series SPU Units OPERATION MANUAL
V237
WS02-SPTC1-V2
SPU-Console OPERATION MANUAL
W124
C200H-TS001/002/101/102
C200H Temperature Sensor Units OPERATION MANUAL
W127
C200H-AD001/DA001
C200H Analog I/O Units OPERATION GUIDE
W325 C200H-AD003
C200H-DA003/DA004
C200H-MAD01
C200H Analog I/O Units OPERATION MANUAL
W225 C200H-TC001/002/003
C200H-TC101/102/103
C200H Temperature Control Units OPERATION MANUAL
W240 C200H-TV001/002/003
C200H-TV101/102/103
C200H Heat/Cool Temperature Control Units OPERATION MANUAL
W241
C200H-PID01/02/03
C200H PID Control Unit OPERATION MANUAL
W141
C200H-CT001-V1/CT002
C200H High-speed Counter Units OPERATION MANUAL
W311
C200H-CT021
C200H High-speed Counter Units OPERATION MANUAL
W224
C200H-CP114
C200H Cam Positioner Units OPERATION MANUAL
W334
C200HW-NC113/213/413
C200HW Position Control Units OPERATION MANUAL
W137
C200H-NC111
C200H Position Control Units OPERATION MANUAL
W128
C200H-NC112
C200H Position Control Units OPERATION MANUAL
W166
C200H-NC211
C200H Position Control Units OPERATION MANUAL
W314
C200H-MC221
C200H Motion Control Units OPERATION MANUAL:INTRODUCTION
W315
C200H-MC221
C200H Motion Control Units OPERATION MANUAL:DETAILS
W165
C200H-ASC02
C200H ASCII Units OPERATION MANUAL
W306
C200H-ASC11/21/31
C200H ASCII Units OPERATION MANUAL
W257
CVM1-PRS71
CVM1-PRS71 Teaching Box OPERATION MANUAL
W304 C200HW-COM01
C200HW-COM02-V1 to
C200HW-COM06-EV1
C200HW Communication Boards OPERATION MANUAL

Network Communications Units
Man.No.
Model
Manual
W309 CS1W-CLK23
CS1W-CLK21-V1
CJ1W-CLK23
CJ1W-CLK21-V1
C200HW-CLK21
CVM1-CLK21
CQM1H-CLK21
CS1W-RPT0□
Controller Link Units OPERATION MANUAL
W370 CS1W-CLK13
CS1W-CLK12-V1
CVM1-CLK12(H-PCF Cable)
CS1W-CLK53
CS1W-CLK52-V1
CVM1-CLK52(GI Cable)
Optical Ring Controller Link Units OPERATION MANUAL
W465 CS1W-EIP21
CJ1W-EIP21
CJ2H-CPU6□-EIP
CJ2M-CPU3□
CS/CJ Series EtherNet/IP Units OPERATION MANUAL
W420 CS1W-ETN21
CJ1W-ETN21 (100Base-TX)
CS/CJ Series Ethernet Units OPERATION MANUAL Construction of Networks
W421 CS1W-ETN21
CJ1W-ETN21(100Base-TX)
CS/CJ Series Ethernet Units OPERATION MANUAL Construction of Applications
W456 CS1W-CRM21
CJ1W-CRM21
CS/CJ Series CompoNet Master Units OPERATION MANUAL
W457
CRT1
CRT1 Series CompoNet Slave Units and Repeater Unit OPERATION MANUAL
W380 CS1W-DRM21-V1
CJ1W-DRM21
CS/CJ Series DeviceNet Units OPERATION MANUAL
W267 CS1W/CJ1W/C200HW
DRT1/DRT2
GT1
CVM1
DeviceNet OPERATION MANUAL
W266 C200HW-SRM21-V1
CS1W-SRM21
CJ1W-SRM21
CQM1-SRM21-V1
SRT1/SRT2
CompoBus/S OPERATION MANUAL
W136 C500-RM001-(P)V1
C120-RM001(-P)
C500-RT001/RT002-(P)V1
C500/C120-LK010(-P)
C200H-RM001-PV1
C200H-RT001/002-P
B500-I/O
C series Rack PCs Optical Remote I/O SYSTEM MANUAL
W308 C200HW-ZW3DV2/ZW3PC2
3G8F5-CLK11/21
3G8F6-CLK21
Controller Link Support Software OPERATION MANUAL
W120 C500-RM201/RT201
C200H-RM201/RT201/202
G71-IC16/OD16
G72C-ID16/OD16
S32-RS1
C series Rack PCs Wired Remote I/O SYSTEM MANUAL
W379 CVM1-DRM21-V1
C200HW-DRM21-V1
DeviceNet Master Units OPERATION MANUAL
W347 C200HW-DRT21
CQM1-DRT21
DRT1
DeviceNet Slaves OPERATION MANUAL
W135 C200H-LK401
C500-LK009-V1
C Series PC Link SYSTEM MANUAL

Support Software
Man.No.
Model
Manual
W463
CXONE-AL□□C-V4
CXONE-AL□□D-V4
CX-One FA Integrated Tool Package SETUP MANUAL
W446
CX-Programmer OPERATION MANUAL
W447
CX-Programmer OPERATION MANUAL : Function Blocks/Structured Text
W366
CX-Simulator OPERATION MANUAL
W464
CX-Integrator OPERATION MANUAL
W344
CX-Protocol OPERATION MANUAL
W433
CX-Position OPERATION MANUAL
W436
CX-Motion-NCF OPERATION MANUAL
W448
CX-Motion-MCH OPERATION MANUAL

MEMO

Terms and Conditions Agreement
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in
materials and workmanship for a period of twelve months from the date of sale by Omron (or such other
period expressed in writing by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED,
ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF
THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on
infringement by the Products or otherwise of any intellectual property right.
(c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the
form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the
non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal
to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible
for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s
analysis confirms that the Products were properly handled, stored, installed and maintained and not subject
to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be
approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or
unsuitability or the results from the use of Products in combination with any electrical or electronic
components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or
addition to the above warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT,
WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which
liability is asserted.

Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which
apply to the combination of the Product in the Buyer’s application or use of the Product.At Buyer’s request,
Omron will provide applicable third party certification documents identifying ratings and limitations of use
which apply to the Product. This information by itself is not sufficient for a complete determination of the
suitability of the Product in combination with the end product, machine, system, or other application or use.
Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to
Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR
PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED
FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any
consequence thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the
user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test
conditions, and the user must correlate it to actual application requirements. Actual performance is subject
to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other
reasons. It is our practice to change part numbers when published ratings or features are changed, or when
significant construction changes are made. However, some specifications of the Product may be changed
without any notice. When in doubt, special part numbers may be assigned to fix or establish key
specifications for your application. Please consult with your Omron’s representative at any time to confirm
actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no
responsibility is assumed for clerical, typographical or proofreading errors or omissions.

1
C200HS Replacement Guide
From C200HS to CJ2
Table of Contents
1. Work flow.........................................................................................................................................................................................................................2
2. Selecting the replacement method ......................................................................................................................................................................3
3. Selecting the model....................................................................................................................................................................................................6
4. Reading data from C200HS .................................................................................................................................................................................. 10
5. Converting the program for CJ2 ........................................................................................................................................................................ 12
6. Writing data to CJ2.................................................................................................................................................................................................. 14
7. Appendix....................................................................................................................................................................................................................... 16
Appendix A. Instructions converted by Change Model on CX-Programmer. ........................................................................................ 16
Appendix B. Change of unit area allocation........................................................................................................................................................ 17
Appendix C. Change in PLC Settings .................................................................................................................................................................... 18
Appendix D. Change of execution timing etc. .................................................................................................................................................... 18
Appendix E. Table of Input/Output Units ............................................................................................................................................................ 19

2
Follow the below work flow to replace C200HS with CJ2. Refer to the reference pages for details.
1. Work flow
1) Preliminary Steps: Take the following steps before starting the replacement work.
Selecting the model
Reading PLC data
Description
Reference Pages
Select the units, programming software, and connecting
cables to replace C200HS with CJ2.
The C200H-series Units cannot be used with CJ2. Read the
reference pages (recommended models and remarks) and
select the models.
Load the program, I/O Memory and other settings from the
C200HS using the programming software and connecting
cable.
Converting and modifying data
Convert the data read from C200HS for CJ2.
Most of the data can be automatically converted; however,
some instructions and some Unit data cannot be converted.
Refer to the reference pages and modify the data and program
separately.
3. Selecting the model
4. Reading data from C200HS
Preparing Units
Prepare the units, programming software, and connecting
cables.
5. Converting the program for
CJ2
Continue to actual replacement work
Start
2) Actual replacement work: Take the following steps to replace C200HS with CJ2
Replacing Units
Writing the data to CJ2
Description
Reference pages
Install the prepared Units instead of C200H-series Units.
*Refer to the SYSMAC CJ Series CJ2 CPU Unit Hardware
USER'S MANUAL (Cat. No. W472) and user's manuals for
Special I/O Units and CPU Bus Units for details of installation.
Transfer the converted data to CJ2
To check the wiring, operate input and output bits to see if
they operate correctly.
Checking operation
Turn ON the power and check the operation.
Related Manuals
Wiring
Wiring for the installed Units.
*Refer to the SYSMAC CJ Series CJ2 CPU Unit Hardware
USER'S MANUAL (Cat. No. W472) and user's manuals for
Special I/O Units and CPU Bus Units for details of wiring.
6. Writing data to CJ2
Replacement completion
1. If production is conducted between uploading the program and executing replacement
work, data handled by the program may change. If so, upload the data right before the
replacement work, modify data (if necessary), and download it to the new PLC.
2. The cycle time of C200HS and CJ2 are different, which may affect system operation. If
so, it is necessary to adjust cycle time in the PLC Setup.

3
2. Selecting the replacement method
When C200H-series Basic I/O Units are replaced with CJ-series Basic I/O Units, rewiring is required. When
C200H-ID215 and C200H-OD215 C200H High-density I/O Units are replaced with CJ-series I/O Units, the same
connecting cables that were connected to C200H High-density I/O Units can be used.
Replacement method
Description
Using Conversion Cables
for C200H High-density
I/O Units
Replace C200H-ID215 with CJ1W-ID231, and
connect CJ1W-ID231 using the same
connecting cables used for C200H-ID215. In
the same way, replace C200H-OD215 with
CJ1W-OD231, and connect CJ1W-OD231
using the same cable used for C200H-OD215.
Pros: Rewiring of I/O Units is not required,
which reduces replacement time.
CPU
CJ-series Units
CJ1W-ID231
Conversion Cable
XW2Z-S010
Connecting cable that was
connected to C200H-ID215
(reuse)
CJ1W-OD231
Conversion
Cable
XW2Z-S011
Connecting cable that was
connected to C200H-OD215
(reuse)

4
•Replacement of C200H-ID215 and C200H-OD215 using Conversion Cables
The same connecting cables that were connected to C200H-ID215 and C200H-OD215 can be used to replace
them with CJ1W-ID231 and CJ1W-OD231.
C200H-series Unit
CJ-series Unit
Conversion Cable
C200H-ID215
CJ1W-ID231
XW2Z-S010
C200H-OD215
CJ1W-OD231
XW2Z-S011
XW2Z-S010
CJ1W-ID231 C200H-ID215
Reused cable
C200H-ID215 CJ1W-ID231 Remarks
Rated input voltage 24 VDC 24 VDC
Operating input voltage 20.4 to 26.4 VDC 20.4 to 26.4 VDC
Input impedance 5.6 kΩ 5.6 kΩ
Make sure that the connected device operates
correctly.
Input current 4.1 mA typical (at 24 VDC) 4.1 mA typical (at 24 VDC)
Make sure that the connected device operates
correctly.
ON voltage 14.4 VDC min. 19 VDC min.
Make sure that the connected device operates
correctly.
OFF voltage 5 VDC max. 5 VDC max.
ON response time
2.5 ms max./15 ms max.
(switchable)
8 ms max. (switchable) Can be set to between 0 and 32 ms in the PLC Setup.
OFF response time
2.5 ms max./15 ms max.
(switchable)
8 ms max. (switchable) Can be set to between 0 and 32 ms in the PLC Setup.
No. of circuits
8 points/common x
4 circuits (32 inputs)
16 points/common x
2 circuits (32 inputs)
The number of circuits decreased from 4 to 2.
Rewire if separate power supplies are used.
High-speed inputs
8 points (when pin 2 of the
DIP switch is ON)
Not supported Use CJ1W-IDP01 for high-speed inputs.
* CN1 COM0 and COM1 and
CN2 COM2 and COM3 are
internally connected in the
CJ-series Unit. When separate
power supplies were used,
rewire to use one common
power supply.

5
XW2Z-S011
CJ1W-OD231 C200H-OD215
Reused cable
C200H-OD215 CJ1W-OD231 Remarks
Rated voltage 5 to 24 VDC 12 to 24 VDC
We recommend you to use 24 VDC instead if 5 VDC
is used.
Max. switching capacity
16 mA/4.5 VDC to
100 mA/26.4 VDC
0.8 A/common,
3.2 A/Unit
0.5 A/point,
2 A/common, 4 A/Unit
Leakage current 0.1 mA max. 0.1 mA max.
Residual voltage 0.7 V max. 1.5 V max.
Make sure that the connected device operates
correctly.
ON response time 0.2 ms max. 0.1 ms max.
Make sure that the connected device operates
correctly.
OFF response time 0.6 ms max. 0.8 ms max.
Make sure that the connected device operates
correctly.
No. of circuits
8 points/common x
4 circuits (32 outputs)
16 points/common x
2 circuits (32 outputs)
The number of circuits decreased from 4 to 2.
Rewire if separate power supplies are used.
Fuses 4 (1 fuse/common) None
When protection is required, connect a protective
device externally.
External power supply
5 to 24 VDC±10%,
90 mA min.
2.8 mA x no. of ON outputs
10.2 to 26.4 VDC,
30 mA min.
Dynamic outputs 30 mA min. Not supported Dynamic outputs are not supported.
* CN1 COM0 and COM1 and
CN2 COM2 and COM3 are
internally connected in the
CJ-series Unit. When separate
power supplies were used,
rewire to use one common
power supply.

6
3. Selecting the model
Outline of the system configuration
C200HS
PC
Expansion Backplane
CJ2
PC
I/O Interface Unit
SYSMAC Support Software
CX-Programmer
CX-Programmer
The table below lists the C200H-series Units and each corresponding CJ-series Unit. Select the CJ-series Unit
which is compatible with the C200H-series Unit or which has similar specifications to the C200H-series Unit.
Refer to the CJ2H-CPU6□-EIP/CJ2H-CPU6□/CJ2M-CPU□□ SYSMAC CJ Series CJ2 CPU Unit Hardware USER'S
MANUAL (Cat. No. W472) for details of the Units.
< CPU Rack >
Unit name
C200H-series Unit
CJ-series Unit
Description
CPU Unit
C200HS-CPU01(-C)
C200HS-CPU03
C200HS-CPU21
C200HS-CPU23
C200HS-CPU31
C200HS-CPU33
[CJ2H]
CJ2H-CPU64(-EIP)
CJ2H-CPU65(-EIP)
CJ2H-CPU66(-EIP)
CJ2H-CPU67(-EIP)
CJ2H-CPU68(-EIP)
[CJ2M]
CJ2M-CPU11/CPU31
CJ2M-CPU12/CPU32
CJ2M-CPU13/CPU33
CJ2M-CPU14/CPU34
CJ2M-CPU15/CPU35
UM 50K steps
UM 100K steps
UM 150K steps
UM 250K steps
UM 400K steps
*The EIP models have one built-in
EtherNet/IP port.
UM 5K steps
UM 10K steps
UM 20K steps
UM 30K steps
UM 60K steps
*The CPU3□ models have one built-in
EtherNet/IP port.
CPU Unit-mounting
Host Link Unit
C200HS-CPU21/23/31/33
Serial port (RS-232C) built
in the CPU Unit.
Power Supply Unit
(For
C200HS-CPU01/01-C/21/31)
CJ1W-PA202
(AC Power Supply Unit)
To use RUN output, prepare an Output Unit
separately.
CJ1W-PA205C
(AC Power Supply Unit)
With replacement notification function.
CJ1W-PA205R
(AC Power Supply Unit)
With RUN output.
(For C200HS-CPU03/23/33)
CJ1W-PD022
(DC Power Supply Unit,
non-insulated type)
To use RUN output, prepare an Output Unit
separately.
CJ1W-PD025
(DC Power Supply Unit)
To use RUN output, prepare an Output Unit
separately.
CPU Backplane
C200H-BC031(-□□)
C200H-BC051(-□□)
C200H-BC081(-□□)
C200H-BC101(-□□)
Unnecessary
[DIN Track]
PFP-50N
PFP-100N
PFP-100N2
CJ-series Units are installed on the DIN
Track. The CPU Backplane is not required.
I/O Control Unit
Unnecessary
CJ1W-IC101
Required to connect a CJ-series Expansion
Rack to a CJ-series CPU Rack.

7
< Memory Cassettes >
Unit name
C200H-series Unit
CJ-series Unit
Description
Memory Unit
EEPROM Unit
C200HS-ME16K
None
The CJ2-series CPU Unit has a nonvolatile
memory for user program in it. The Memory
Unit is not required.
It also has the clock function.
The program file and the parameters are
stored in the memory card. It is possible to
execute operation by reading them when the
PLC is turned ON. (Automatic File Transfer
at Startup)
EPROM Unit
C200HS-MP16K
None
The CJ2-series CPU Unit has a nonvolatile
memory for user program in it. The Memory
Unit is not required.
It also has the clock function.
The program file and the parameters are
stored in the memory card. It is possible to
execute operation by reading them when the
PLC is turned ON. (Automatic File Transfer
at Startup)
< Expansion Rack >
Unit name
C200H-series Unit
CJ-series Unit
Description
Power Supply Unit
C200H-PS221
CJ1W-PA202
(AC Power Supply Unit)
CJ1W-PA205C
(AC Power Supply Unit)
With replacement notification function.
CJ1W-PA205R
(AC Power Supply Unit)
The RUN output does not operate.
C200H-PS211
CJ1W-PD022
(DC Power Supply Unit,
non-insulated type)
CJ1W-PD025
(DC Power Supply Unit)
Backplane
(Expansion Backplane)
C200H-BC031(-□□)
C200H-BC051(-□□)
C200H-BC081(-□□)
C200H-BC101(-□□)
Unnecessary
[DIN Track]
PFP-50N
PFP-100N
PFP-100N2
CJ-series Units are installed on the DIN
Track. The Backplane is not required.
I/O Interface Unit
Unnecessary
CJ1W-II101
Required for each CJ-series Expansion
Rack.
I/O Connecting Cable
C200H-CN311 (0.3 m)
C200H-CN711 (0.7 m)
C200H-CN221 (2 m)
C200H-CN521 (5 m)
C200H-CN131 (10 m)
CS1W-CN313 (0.3 m)
CS1W-CN713 (0.7 m)
CS1W-CN223 (2 m)
CS1W-CN323 (3 m)
CS1W-CN523 (5 m)
CS1W-CN133 (10 m)
CS1W-CN133-B2 (12 m)
Connects an I/O Control Unit to an I/O
Interface Unit or connects an I/O Interface
Unit to another I/O Interface Unit.

8
< I/O Units and CPU Bus Units>
Unit name
C200H-series Unit
CJ-series Unit
Description
Basic I/O Unit
C200H-I□□□
C200H-O□□□
C200H-M□□□
CJ1W-I□□□
CJ1W-O□□□
CJ1W-M□□□
Refer to Appendix E. Table of Input/Output
Units for CJ-series Basic I/O Units
corresponding to C200H-series Basic I/O
Units.
Special I/O Unit
C200H-□□□□
CJ1W-□□□□
Select a required model to replace the
C200H-series Unit. Refer to the manuals of
Special I/O Units for specifications.
When there is no CJ-series Special I/O Unit
which has the same functions and
specifications as the C200H-series Unit, we
recommend you to use another CJ-series
Special I/O Unit instead.
Communication Unit
[SYSMAC LINK]
Coaxial:
C200H-SLK21-V1
C200HS-SLK22
C200HW-SLK23/24
Optical:
C200H-SLK11
C200HS-SLK12
C200HW-SLK13/14
[SYSMAC LINK]
None
[Controller Link]
Wired: CJ1W-CLK23
Optical: None
SYSMAC LINK cannot be used with the
CJ2-series CPU Unit.
We recommend you to use Controller Link
instead.
Refer to the Controller Link Units Operation
Manual (Cat. No. W309) for details.
[SYSMAC NET]
C200H-SNT31
C200HS-SNT32
[SYSMAC NET]
None
[Controller Link]
Wired: CJ1W-CLK23.
Optical: None
SYSMAC NET cannot be used with the
CJ2-series CPU Unit.
We recommend you to use Controller Link
instead.
Refer to the Controller Link Units Operation
Manual (Cat. No. W309) for details.
[Host Link]
[Serial Communications]
C200H-series Host Link Units cannot be
used with the CJ2-series CPU Unit.
Refer to the SYSMAC CS/CJ Series Serial
Communications Boards/Units OPERATION
MANUAL (Cat. No. W336) for details.
C200H-LK101-PV1
None
CJ1W-SCU21-V1
(+ optical link module)
The CJ Series does not have an Optical-type
Serial Communications Board/Unit. Use the
wired type instead or use an external optical
link module.
C200H-LK201-V1
CJ1W-SCU21-V1
CJ1W-SCU41-V1
Host Link port built in the
CPU Unit
*For CJ2M-CPU3□,
CP1W-CIF01 is required.
Use one of the left CJ-series Units/Boards..
*CJ2M-CPU3□does not have a built-in Host
Link port. Purchase the CP1W-CIF01
RS-232C Option Board.
C200H-LK202-V1
CJ1W-SCU31-V1
CJ1W-SCU41-V1
Use one of the left CJ-series Units/Boards.
[PC Link]
C200H-LK401
[PC Link]
None
[Controller Link]
Wired: CJ1W-CLK23.
Optical: None
PC Link cannot be used with the CJ2-series
CPU Unit.
We recommend you to use Controller Link
instead.
Refer to the Controller Link Units Operation
Manual (Cat. No. W309) for details.
[SYSMAC BUS]
Wired: C200H-RM201
Optical: C200H-RM001-PV1
[SYSMAC BUS]
None
[CompoNet]
CJ1W-CRM21
[DeviceNet]
CJ1W-DRM21
[CompoBus/S]
CJ1W-SRM21
SYSMAC BUS cannot be used with the
CJ2-series CPU Unit.
We recommend you to use left networks
instead.
Refer to the CS/CJ series CompoNet Master
Units OPERATION MANUAL (Cat. No.
W456) and CompoNet Slave Units and
Repeater Unit OPERATION MANUAL (Cat.
No. W457) for details of CompoNet.
Refer to the
CS1W-DRM21(-V1),CJ1W-DRM21 CS/CJ
SERIES DeviceNet UNITS OPERATION
MANUAL (Cat. No. W380) for details of
DeviceNet.
Refer to the
C200HW/CS1W/CJ1W/CQM1/SRT1/SRT2
CompoBus/S OPERATION MANUAL (Cat.
No. W266) for details of CompoBus/S.

9
< Support Software and Peripheral Devices >
Name
C200H-series Unit
CJ-series Unit
Description
Support Software
SYSMAC C-series Ladder
Support Software
C500-SF610-V6 (5 inches)
C500-SF410-V6 (3.5 inches)
CX-Programmer
CX-One
CXONE-AL□□C-V□/
AL□□D-V□
(CX-Programmer)
SYSMAC Support Software cannot be used
with the CJ2-series CPU Unit.
Peripheral Interface
Unit, Connecting Cable
CQM1-CIF02
Commercially available
USB cable
USB 2.0 (or 1.1) cable
(A connector – B connector) 5.0 m max..
Programming Console
C200H-PRO27
(+C200H-CN222/422)
(+C200HS-CN222/422)
CQM1-PRO01
(+C200HS-CN222 attached)
None
Use the CX-Programmer or Programming
Console function of the NS-series
Programmable Terminal.
Other remarks
(1) The CJ2-series CPU Unit is separated from the Power Supply Unit although the C200HS-series CPU Unit
is combined with the Power Supply Unit.
(2) The PFP-50N/100N/100N2 DIN Track and C200H-DIN01 Mounting Bracket can be used to install the
CJ-series Units on the DIN Track.
(3) The CJ-series Unit has an installation structure to be insulated from the control panel (DIN Track). The
C200H-ATT31/51/81/A1 Insulation Plate for CPU Backplane is not required.

10
4. Reading data from C200HS
Load the ladder program, PLC settings, and Data Memory from C200HS using the CX-Programmer.
Required items
Support Software
(PC)
CX-One
(CXONE-AL□□C-V□, CXONE-AL□□D-V□)
or
CX-Programmer (WS02-CXPC□-V□)
Connecting Cable
CQM1-CIF02
C200HS
PC
CX-Programmer
Connecting Cable
CQM1-CIF02
Connector for programming device
(1) Connect C200HS and a PC using a connecting cable.
(2) Start up the CX-Programmer. (Select All Program - OMRON - CX-One - CX-Programmer - CX-Programmer
from the Windows Start Menu.)
(3) Select C200HS for the Device Type. (Select New from the File Menu to display the below dialog box.)

11
(4) Select Work Online from the PLC Menu to go online.
(5) Transfer the ladder program and I/O table. (Select Transfer - From PLC from the PLC Menu.)
Click the OK Button to start transfer.
(6) Transfer the PLC memory data (Data Memory). (Select Edit - Memory from the PLC Menu.)
Scroll and select all the areas. Click the Transfer from PLC Button to start transfer.
(7) Select Work Online from the PLC Menu to go offline.
(8) Save the program with a new project name. (Select Save As from the File Menu.)