One Forall KAMELEON 5 User manual

WWW.ONEFORALL.COM 1
PICTURE OF ONE FOR ALL 5 REMOTE 2
INSTALLING THE BATTERIES 3
THE KEYPAD 3
SETTING UP THE ONE FOR ALL 5 6
(How to set up the ONE FOR ALL 5 to control your devices)
SEARCH METHOD 7
CODES
• Televisions 127
• Video Recorders 135
• Satellite Receivers 137
• Cable Converters 140
• Video Accessory 141
• Miscellaneous Audio 141
• Amplifier 141
• Amp. / Tuner 141
• DVD 142
CODE BLINK OUT
(To find out which code is currently programmed) 8
QUICK CODE REFERENCE 8
THE LEARNING FEATURE 9
(How to copy functions from your original working
remote onto the ONE FOR ALL 5)
OPERATIONAL RESET 11
EXTRA FEATURES
• Mode re-assignment (Changing a device mode) 12
• Volume Punch-Through 13
• Macros (Sequence of commands) 14
• Key Magic (How to program missing functions) 16
• Colour and Brightness 17
TROUBLE-SHOOTING 17
CUSTOMER SERVICE 18
Table of Contents
Your ONE FOR ALL 5 can operate five devices:
TV : Television
VCR : Video Recorder
SAT : Satellite Receiver or Cable Converter
DVD : DVD Player
AMP : Amplifier / Tuner
Also, what makes the ONE FOR ALL 5 even more unique is the
"Learning" feature, which allows you to customise any of the special
functions of your original remote control onto the keypad of your
new ONE FOR ALL 5.
The following pages explain in simple steps how to customise
the ONE FOR ALL 5 to your devices.
You may need this guide again in the future, so please be sure
to keep it.
About Your ONE FOR ALL 5
English
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 1

2WWW.ONEFORALL.COM
9
10
3
4
6
8
11
12/13
7
2
1
14
5
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 2

WWW.ONEFORALL.COM 3
Installing the Batteries
Your ONE FOR ALL 5 requires 4 new “AAA/LR03”alkaline batteries.
1Push the battery door upwards and lift it up to remove it.
2Match the batteries to the (+) and (–) marks inside the battery case,
then insert the batteries.
3Replace the battery cover by pushing downwards and allowing
it to click back into position.
See picture of ONE FOR ALL 5 remote on page 2.
1Magic Key
The MAGIC key is used to set up your ONE FOR ALL 5.
2Power
The POWER key operates the same function it did on your original
remote control.
3Backlight Device Keys
The TV, VCR, SAT, DVD, and AMP keys select the home entertainment
device to be controlled. For example pressing the TV key allows
the remote to control the functions of your Television, after pressing
VCR you can operate your Video Cassette Recorder etc.
For more detailed information, please refer to the chart on page 6.
During operation of the ONE FOR ALL the red light (LED - Light Emitting
Diode) underneath a device key will light up (every time a key is pressed)
to indicate the device mode you are using.
4Number Keys (0-9, -/- -, AV)
The Number keys (0-9, -/--, AV) provide functions just like your
original remote, such as direct access channel selection. If your
original remote uses one/two digit input switching (-/-- symbol),
this function can be obtained by pressing the -/-- key. If your original
remote has an 10 key, this function can also be found under
the -/-- key. If your original remote has an 20 key, this function can also
be found under the AV key. In AMP mode the Number keys may provide
source (input) selection.
5AV Key
In TV mode you will obtain the AV / Input function. In VCR mode you will
obtain the “TV/VCR”function, if available on your original remote. In
DVD mode you will obtain the “TV/DVD”function, if available on your
original remote. In DVD mode you will obtain the “TV/SAT”or “TV/DTV”
function, if available on your original remote.
6Volume +/- Keys
These keys operate in the same way as the keys on your original remote.
The Keypad
Important notes:
- On the inside of the battery compartment door you will find
a label on which to write your Set-Up codes after your ONE FOR ALL 5
is set up for your device. Please write down your codes
for easy, future reference.
- Do not use rechargeable batteries.
- Upon changing the batteries, your set-up codes and advanced pro-
gramming will be retained.
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 3

4WWW.ONEFORALL.COM
7Mute Key
The Mute key operates the same function it did on your original remote
control.
8Menu Key
The MENU key controls the same function as it did on your original
remote.
9Channel +/- Keys
These keys operate in the same way as the keys on your original remote.
10 Directional Keys
If available on your original remote, these keys will allow you to navigate
through the menu mode of your device.
11 OK
The OK key will confirm your choice in menu operation.
12 Transport Keys (VCR / DVD)
These keys operate the transport functions (PLAY, FF, REW etc.) of your
device. To prevent accidental recording, the RECORD key mustbe pressed
twice to start recording.
13 Teletext Keys
After pressing the TV key, the transport keys (REW, PLAY, PAUSE, FF) are
used to operate the main Teletext functions. The symbols below the keys
are for Teletext. The text keys are used to access the Teletext functions of
your television. Of course, your television must have Teletext capability.
TEXT ON: Puts the television in the Teletext mode.
TEXT OFF: Switches the television back to regular viewing mode.
On some televisions, this may be done by pressing the TEXT ON key
several times.
HOLD/STOP: Stops changing pages.
MIX: Shows teletext and regular television simultaneously.
You may also use this key for subtitling. On some televisions
this function is accessed by pressing the text key twice.
EXPAND: Shows the top half of the Teletext page in larger letters. By
pressing again, you can see the bottom half of the Teletext page enlar-
ged. To return to regular Teletext viewing, press the EXPAND key again,
or press the TEXT ON key, depending on your television.
INDEX: This key will give you access to the index function within the
text mode.
After pressing the TV key and accessing the text mode, the keys marked
red, green, yellow and blue, allow you to access the Fastext functions
of your television. If on your original remote control these keys are
used for Menu navigation, the ONE FOR ALL Fastext keys may
operate in the same way.
i
The Keypad
Important note: For a more detailed explanation of Teletext and Fastext, please
refer to the manual of your television. Remember, different televisions control
Teletext and Fastext features in different ways. Not all of the Teletext functions
may be available for your particular model.
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 4

WWW.ONEFORALL.COM 5
14 Additional Function Keys
Guide
In TV and/or SAT mode you will obtain the “Guide”
function, if available on your original remote.
I
In TV and/or SAT mode you may obtain the ‘Display”, “OSD”or
“info”function, if available on your original remote.
?
In SAT mode you will obtain the “help”function, if
available on your original remote.
Back
In TV, VCR and DVD mode you will obtain the “Menu Exit”
function, if available on your original remote. In SAT menu
mode you may use the “back”key to go to the previous menu
screen.
PPV
In SAT mode you will obtain the Pay Per View (PPV)
function, if available on your original remote.
Subt.
In TV, VCR, SAT and DVD mode you will obtain the “Subtitle”
function, if available on your original remote.
Radio
In SAT mode you will obtain the “Radio”function, if
available on your original remote.
Fav
In TV mode this key provides you the (16:9) wide screen view
function, if available on your original remote). In SAT mode
you will obtain the “Favorite”function, if available on your
original remote.
The Keypad
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 5

6WWW.ONEFORALL.COM
Example: To set up the ONE FOR ALL 5 for your Television:
1 Find the code for your device in the Code list (page 127 –
146). Codes are listed by device type and brand name.
The most popular code is listed first. Make sure your
device is switched on (not on standby).
2 Press the TV key on the ONE FOR ALL 5 for the device you
wish to Set-Up.
3 Press and hold down MAGIC until the ONE FOR ALL 5’s
TV key blinks twice (the red LED underneath the TV key will
blink once and then twice).
4Enter your four-digit device code using the number keys.
The device key will blink twice.
5Now, aim the ONE FOR ALL 5 at your device and press
POWER. If your device switches off, the ONE FOR ALL 5
is ready to operate your device.
6Turn your device back on and try all the remote’s functions to ensure they
are working properly. If the functions do not work properly, repeat steps
1-5 using another code listed under your brand.
7 If your device does not respond, follow steps 1 to 5 with each
code listed for your brand. If none of the codes listed for your
brand operate your device, or if your brand is not listed at all, try
the Search Method described on page 7.
8 Write your code in the four boxes provided in the battery
compartment and on page 8 for easy future reference.
Setting up the ONE FOR ALL 5
(How to set up the ONE FOR ALL 5 to control your devices)
- Some codes are quite similar. If your device does not respond or is not
functioning properly with one of the codes, try another code listed under your
brand.
- If your device’s original remote control does not have a POWER key, press PLAY
instead of POWER when setting up your device.
- Remember to press the corresponding device key before operating your device.
ONE FOR A
Acura
Admiral
Adyson
Agazi
AGB
Agef
Aiko
0009
0087, 0093, 0363, 041
0217, 0216
0264
0516
0087
0216, 0009, 0037, 0
0037, 0274
0361, 0208, 0371
____
Devices can be found under the following keys:
To set up a second TV, VCR, SAT, DVD or AMP see page 12.
* DVBT codes (Digital Terrestrial / Free View) can be found in
the ”Satellite Receiver”section.
Video Recorder
Television
Satellite Receiver (also DVBT*) /
Cable Converter
Video Accessory
Amplifier
Amp. / Tuner
Miscellaneous Audio
DVD / DVD-R
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 6

WWW.ONEFORALL.COM 7
- Most TV’s do not switch on pressing the POWER key. Please try pressing a
“number”key or the “TV-text off”key to switch your TV back on.
- If you cannot control your Television properly, please continue the Search
Method, you may be using the wrong Code.
- To search for the code for another device follow the instructions above only
press the appropriate device key instead of TV during step 2.
- If the original remote control of your Video recorder or DVD player does not
have a POWER key, press PLAY instead of POWER during step 5.
Setting up the ONE FOR ALL 5
Search Method
--> If your device does not respond to the ONE FOR ALL 5 after you
have tried all the codes listed for your brand.
--> If your brand is not listed at all.
The Search Method allows you to scan through all the codes contained
in the memory of the ONE FOR ALL 5.
Example: To search for your TV code:
1Switch your television on (not on standby) and aim your ONE FOR ALL
at your TV.
2Press the TV key on your ONE FOR ALL 5.
3 Press and hold down MAGIC until the ONE FOR ALL 5’s
TV key blinks twice (the red LED underneath the TV key
will blink once and then twice).
4Press 9 9 1. The TV key will blink twice.
5Next, press POWER.
6Aim the ONE FOR ALL 5 at your Television. Now press CH+ over
and over, until your Television turns off (every time you press
the CH+ key the ONE FOR ALL 5 will send out a POWER signal
from the next code contained in the memory). You may have
to press this key many times (up to 150 times) so please
be patient. If you skip past a code, you can go to the previous
code(s) by pressing the CH- key. Remember to keep pointing
the ONE FOR ALL 5 at your Television while pressing this key.
7As soon as your television turns off, press MAGIC to store the
code.
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 7

8WWW.ONEFORALL.COM
Once you have Set-Up your ONE FOR ALL 5, you can blink back your
SET-UP CODE for future reference.
Example: To blink out your Television code:
1Press TV once.
2 Press and hold down MAGIC until the ONE FOR ALL 5’s
TV key blinks twice (the red LED underneath the TV key will
blink once and then twice).
3Press 9 9 0. The TV key will blink twice.
4For the first digit of your four-digit code, press 1and count
all the red blinks. If there are no blinks, the digit is "0".
5For the second digit, press 2and count all the red blinks.
If there are no blinks, the digit is "0".
6For the third digit, press 3and count all the red blinks.
If there are no blinks, the digit is "0".
7For the fourth digit, press 4and count all the red blinks.
If there are no blinks, the digit is "0". Now you have your
four-digit code.
Quick Code Reference
Write down the codes for your devices in the boxes below and in
the battery compartment for quick and easy reference.
Device Type Code
1._________________________
2._________________________
3._________________________
4._________________________
5._________________________
■■■■■■ ■■
■■■■■■ ■■
■■■■■■ ■■
■■■■■■ ■■
■■■■■■ ■■
Code Blink out
(To find out which code is currently programmed)
- To blink back the code for your other devices press the appropriat device key
during step 1.
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 8

WWW.ONEFORALL.COM 9
The ONE FOR ALL 5 comes with a complete library of pre-programmed
codes. After you have set up the ONE FOR ALL 5 for your device, you may
find that there are one or more keys that you had on your original remote,
which do not have a place on the ONE FOR ALL keypad.
As a convenience, the ONE FOR ALL 5 offers a special Learning feature that
allows you to copy any function from your original remote control onto the
keypad of the ONE FOR ALL 5.
Before you start:
- Make sure your original remote control is working correctly.
- Make sure neither your ONE FOR ALL, nor your original remote control is
pointing at your device.
•Learning (Direct)
Example: To copy the “mono/stereo”function from your original TV
remote onto the ”Radio”key of your ONE FOR ALL 5.
1 Place both remote controls (the ONE FOR ALL 5 and your original) on
a flat surface. Make sure the ends which you normally point at your
device are facing each other. Keep the remotes at a distance of
2 to 5 cm.
2 Press and hold the MAGIC key until one of the device
keys will blink twice. The red LED underneath the
corresponding device key (depending on the device mode
that was selected) will blink once then twice.
3 Press 9 7 5 (the device key will blink twice).
4Press the device key (on the ONE FOR ALL remote) to select
the mode to which you want to copy the learned function
(Example: TV key).
5 Press the key (on the ONE FOR ALL remote) where you
want to place the learned function (Example: ”Radio”key).
The device key will flash rapidly.
6 Press and hold the key (on your original remote) that you
want to copy until the device key on the ONE FOR ALL blinks
twice (Example: “mono/stereo”key).
7If you want to copy other functions within the same mode, simply repeat
steps 5 and 6 pressing the next key you want to copy by learning.
8To exit the learning mode, press and hold MAGIC until
the device key blinks twice.
9Learning is mode specific. To access your learned function,
press the appropriate device key first.
The Learning Feature
(How to copy functions from your original working remote
onto the ONE FOR ALL5)
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 9

10 WWW.ONEFORALL.COM
The Learning Feature
•Shifted Learning
You can also learn a function on a key of the ONE FOR ALL without
sacrificing the original ONE FOR ALL function. A Shifted Learning function can
also be put on any key EXCEPT for the following: Device keys, MAGIC key,
Number keys. To install a Shifted Learning function, simply follow steps 1-8 on
the previous page. During step 5, press MAGIC once before you press the key
where you are placing the learned function.
To access the shifted function, press MAGIC and then the key you have
learned on.
Important notes:
- During steps 2 - 7 (page 9), you have approximately 10 seconds to conduct each
step. If there is a gap of more than 10 seconds between two steps, you will have
to start again from step number 2.
- If you learn a function on a key, the original ONE FOR ALL feature automatically
becomes shifted. You can press MAGIC then the key to access it (this excludes the
Channel and Volume keys).
- The Learning feature is mode specific. Therefore you can place one learned fea-
ture per mode on the same key.
- If a Shifted Learned function is placed on the Channel and Volume keys then
Colour/Brightness will be sacrificed.
- The ONE FOR ALL 5 can learn approximately 25 –40 functions.
- You can replace a learned function by placing another learned function on top.
- Learning should not be done in direct sunlight or under incandescent lights.
- Make sure you are using new batteries before following the instructions above.
- Upon changing the batteries, your learned functions will be retained.
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 10

WWW.ONEFORALL.COM 11
To delete a learned function:
1 Press and hold the MAGIC key until one of the device keys will
blink twice. The red LED underneath the corresponding device key
(depending on the device mode that was selected) will blink once then
twice.
2Press 9 7 6 (the device key will blink twice).
3Press the device key in which the function will be deleted.
4Press twice on the learned key which will be deleted
(the device key will blink twice).*
5If there is another key which you wish to delete, repeat steps 1-4.
6The original functions of the ONE FOR ALL 5 will now be present.
* To delete a Shifted Learned feature, press MAGIC before you press
the learned key to be deleted (during step 4).
To delete all learned functions within a specific mode:
1 Press and hold the MAGIC key until one of the device keys will
blink twice. The red LED underneath the corresponding device key
(depending on the device mode that was selected) will blink once then
twice.
2Press 9 7 6 (the device key will blink twice).
3Press the appropriate device (mode).
Operational Reset
The Operational Reset will erase all learned functions across all modes and
some other programmed functions like Key Magic and Macros.
1 Press and hold the MAGIC key until one of the device keys will
blink twice. The red LED underneath the corresponding
device key (depending on the device mode that was selected)
will blink once then twice.
2Press 9 8 0 (the device key will blink four times).
The Learning Feature
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 11

12 WWW.ONEFORALL.COM
It is possible to change the mode of any device key. This is useful if you
want to set up two of the same devices on the ONE FOR ALL 5. The code
can be set up using “Direct code set up”(p. 6) or “Search method”(p. 7).
To change a device key, see the three examples below.
Example 1) if you want to program a second TV on the VCR key.
Example 2) if you want to program a second TV on the SAT key.
Example 3) if you want to program a second VCR on the SAT key.
Example 1:
To program a second Television on the VCR key (for example), you need
to change the VCR key into a TV key, so press:
(*) (**)
The VCR key has now become a second TV key.
Now enter the Set-Up code for your second TV by pressing:
(*) (TV code) (**)
Example 2:
To program a second Television on the SAT key (for example), you need
to change the SAT key into a TV key, so press:
(*) (**)
The SAT key has now become a second TV key.
Now enter the Set-Up code for your second TV by pressing:
(*) (TV code) (**)
Example 3:
To program a second Video Recorder on the SAT key (for example), you
need to change the SAT key into a VCR key, so press:
(*) (**)
The SAT key has now become a second VCR key.
Now enter the Set-Up code for your second VCR by pressing:
(*) (VCR code) (**)
Resetting a Device key
Example: To reset the VCR key to its original mode, press:
(*) (**)
Example: To reset the SAT key to its original mode, press:
(*) (**)
(*) Press and hold down the MAGIC key until the red light (LED)
blinks twice.
(**) The red light (LED) will blink once then twice.
Extra Features
Mode re-assignment
(Changing a device mode)
____
____
____
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 12

WWW.ONEFORALL.COM 13
Volume Punch Through
You may be able to use some functions of your Television, Video recorder,
DVD player, Amp./Tuner, Satellite receiver or Cable converter at the same time.
For example: if you are watching a program on your video recorder, you can
adjust the volume (a TV function) without pressing the TV mode key on your
ONE FOR ALL 5.
To punch through to TV volume while in the VCR, DVD, AMP or SAT
mode:
1. Press and hold the MAGIC key until one of the
device keys will blink twice. The red LED underneath
the corresponding device key (depending on the device
mode that was selected) will blink once then twice.
2. Press 9 9 3.
3. Then press the TV key and the red light will
blinktwice.
To cancel the “Volume Punch Through”per mode:
(Example: to cancel the “Volume Punch Through”for the VCR mode)
1. Press VCR once.
2 Press and hold down MAGIC until the ONE FOR ALL
5’s VCR key blinks twice (the red LED underneath the
VCR key will blink once and then twice).
3. Press 9 9 3.
4. Then press the Volume (-) key and the red light
will blink four times.
Result: being in VCR mode, you will be able to control VOL+/- or MUTE
functions of your VCR (provided it has volume control).
To cancel the „Volume Punch Through“:
1 Press and hold the MAGIC key until one of
the device keys will blink twice. The red LED
underneath the corresponding device key
(depending on the device mode that was
selected) will blink once then twice.
2. Press 9 9 3.
3. Press the Volume (+) key and the red light will blink
four times.
Extra Features
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 13

14 WWW.ONEFORALL.COM
Macros (Sequence of commands)
Extra Features
Macros (Direct)
You can program your ONE FOR ALL 5 to issue a sequence of commands at
the press of one button. Any sequence of commands you regularly use can be
reduced to one key stroke for your convenience. For example, you may want to
turn off your TV, VCR and Satellite at the same time.
Example: To set up the Macro mentioned above on the key labeled
”Radio”on your ONE FOR ALL 5:
1 Press and hold the MAGIC key until one of the device keys will
blink twice. The red LED underneath the corresponding device key
(depending on the device mode that was selected) will blink once then
twice.
2Press 9 9 5.
3Then press the Radio key to which the Macro will be assigned.
4Next press TV, POWER, VCR, POWER, SAT, POWER.
5To store the Macro, press and hold MAGIC until the device key blinks
twice (the device key will blink once then twice).
6Whenever you press the ”Radio”key, the ONE FOR ALL 5 will turn off
your TV, VCR and Satellite.
•To erase the Macro from the Radio key, press:
MAGIC* 9 9 5 Radio key MAGIC*
*Here you must hold down MAGIC until the device key blinks twice.
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 14

WWW.ONEFORALL.COM 15
Shifted Macros
You can install a Shifted Macro on any key, except for the device
keys (TV, VCR, SAT, DVD and AMP), the MAGIC key, and the
NUMBER keys.
If for example, you want to program a shifted Macro on the POWER key,
simply press MAGIC once then the POWER key during step 3.
Now everytime you press MAGIC, then the POWER key, the ONE FOR ALL
will turn off your TV, VCR and Satellite.
•To erase the Shifted Macro from the POWER key press:
MAGIC* 9 9 5 MAGIC POWER key MAGIC*
* Here you must hold down MAGIC until the device key blinks twice.
- Each MACRO can consist of a maximum of 15 key strokes.
- Make sure that you program a Macro on a spare key that you don’t use
in any mode.
- Once you program a Macro on a specific key, the sequence will work regardless
of the mode (TV, VCR, SAT, DVD and AMP) you are using.
- To avoid accidental recordings with the ONE FOR ALL 5, you must press
the Record key twice to begin recording. Because of this, you cannot assign a
Macro or Shifted Macro to the Record key.
- If you had to hold down a key for a few seconds on the original remote control
to get a function, this function may not work in a macro on your ONE FOR ALL
remote.
- If you program a Macro on a key, the original function will become shifted
(excluding CH+/- and VOL+/- keys). Press MAGIC then the key to access it. If you
place a Macro shifted on a digit key, access the original function by pressing
MAGIC twice and then the digit key.
- If a Shifted Macro is placed on the Channel and Volume keys then the Colour
and Brightness feature will be sacrificed.
Extra Features
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 15

16 WWW.ONEFORALL.COM
Key Magic®
how to program missing functions
Key Magic is an exclusive ONE FOR ALL feature. The design of the ONE FOR
ALL ensures that many functions of your original remote control can be
operated - even those that do not have their own key on the ONE FOR ALL
keypad. Frequently used functions can be assigned to a key of your choice
using the Key Magic feature of your ONE FOR ALL.
In order to program a certain function with Key Magic you need to know
the corresponding function code. As the function codes vary with different
types of devices, they cannot be found in the manual. You can request your
function codes through our consumer service help-line or by letter, fax or
e-mail.
All we need to know is:
•The 5-digit set-up code your device is working with.
•How the function was labelled on your original remote control.
You can also visit our website
(www.oneforall.com)
to find an answer to your questions.
Once you obtain(ed) your function code(s) from customer service, programming
the code is easy:
1Press the device key (TV, VCR, SAT, DVD and AMP).
2 Press and hold the MAGIC key until one of the device keys will
blink twice. The red LED underneath the corresponding
device key (depending on the device mode that was selected) will blink
once then twice.
3Press 9 9 4. The device key will blink twice.
4Press the MAGIC key once.
5Enter the 5-digit function code (provided by customer service).
6Press the key to which the function will be assigned. The device key
will blink twice.
EXTENDED FUNCTION REFERENCE
(first entry is an example):
DEVICE SET-UP CODE FUNCTION FUNCTION CODE
TV 0556 16/9 format 00234
- To access the function you have programmed, press the corresponding
device key first.
- Key Magic can be assigned to any key EXCEPT the Device keys and
the MAGIC key.
- Please note all the extended function codes you obtain from customer
service for easy future reference.
Extra Features
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 16

WWW.ONEFORALL.COM 17
Trouble-Shooting
Problem:
Your brand is not listed
in the code section?
The ONE FOR ALL does
not operate your
device(s)?
The ONE FOR ALL is not
performing commands
properly?
Problems changing
channels?
Video not recording?
The ONE FOR ALL does
not respond after
pressing a key?
The device key does not
blink when you press
a key?
Solution:
Try the search method on page 7.
A) Try all the codes listed for your brand.
B) Try the search method on page 7.
You may be using the wrong
code. Try repeating the Direct
Set-Up using another code listed
under your brand or start the
search method over again to
locate the proper code.
Enter the channel number
exactly as you would on your
original remote.
As a safety feature on your
ONE FOR ALL, you must press
the Record key twice.
Make sure you are using new
batteries and are aiming the
ONE FOR ALL at your device.
Replace batteries with 4 fresh,
new AAA/LR03”alkaline batteries.
Depending on the functions of your original remote control, the ONE FOR ALL
may operate the colour and brightness settings of your television.
Colour (+) = Press and release MAGIC then hold Volume (+)
Colour (-) = Press and release MAGIC then hold Volume (-)
Brightness (+) = Press and release MAGIC then hold Channel (+)
Brightness (-) = Press and release MAGIC then hold Channel (-)
Colour and Brightness
Extra Features
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 17

18 WWW.ONEFORALL.COM
If you still have questions about the operation of your ONE FOR ALL 5
universal remote and could not find the answer(s) in the Trouble Shooting
section, you may want to contact the customer service department for
assistance.
You may care to visit our Internet-site: www.oneforall.com
Our internet-site has many advantages:
- 24 hours access
- no waiting time
- page for Frequently Asked Questions
- info about the ONE FOR ALL product range
Before contacting us, by Fax, E-mail or Phone, make sure you have
the required information available by filling in the table below.
What do we need to know before you contact us:
1That you have the ONE FOR ALL 5 URC-7555 (*)
universal remote.
2The date of purchase (.........../.........../...........).
3A list of your equipment/models: (see example below).
Device Brand Device Remote SET-UP
model nr. model nr. code
TV Sony KV-25C5D RM-883 1505 (example)
Type/model numbers can often be found in your equipment owner’s
manual or on the factory plate behind the device.
4. Then Fax, E-mail or Dial us:
In the UK
E-mail : [e-mail] (***)
Fax : [phone]
Tel. : [phone] (£ 0,50 per minute) (*) (**)
In Ireland In Australia
E-mail : [e-mail] (***) E-mail : [e-mail] (***)
Fax : [phone] Fax : [phone]
Tel. : [phone] (*) (**) Tel. : [phone]
In South Africa In New Zealand
E-mail : [email protected] E-mail : [e-mail] (***)
Fax : [phone] Fax : [phone]
Tel. : [phone] Tel. : 0508 ONE 4 ALL (663 4 255)
Tel. : [phone]
(*) When you call us you will be asked to enter a URC-number.
The URC-number of your ONE FOR ALL 5 is a 7555.
(**) When calling with a mobile phone:
- You may be charged extra when calling us from; the UK or France.
- You may not be able to contact us when calling from; Belgium, the
Netherlands, Luxemburg, Greece, Portugal, Switzerland, Italy, Ireland or
Austria.
(***) Just send a blank message, you’ll get auto-reply.
Customer Service
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 18

WWW.ONEFORALL.COM 19
ABBILDUNG DER ONE FOR ALL 5 FERNBEDIENUNG 20
BATTERIEWECHSEL 21
FUNKTIONSTASTEN 21
EINSTELLUNG DER ONE FOR ALL 5 24
(Wie Sie die ONE FOR ALL 5 auf Ihre Geräte einstellen)
CODE SUCHLAUF 25
EINSTELLCODES
•Fernseher 127
•Videorecorder 135
•Satellitenempfänger 137
•Kabeldecoder 140
•Video Accessory 141
•Miscellaneous Audio 141
•Audioverstärker 141
•Verstärker/Tuner 141
•DVD 142
CODE AUSLESEN
(Um heraus zu finden welcher Code Aktuell programmiert ist) 26
PERSÖNLICHE CODE-ÜBERSICHT 26
LERNFÄHIGKEIT 27
(Funktionen von Ihrer Originalfernbedienung auf
die ONE FOR ALL 5 kopieren.)
BENUTZER RESET 29
EXTRA FUNKTIONEN
• Gerätemodus Neuzuordnung (Wenn Sie zwei Geräte
gleicher Art auf der ONE FOR ALL 5 einstellen möchten) 30
• Lautstärke Direktbedienung 31
• Makros (Bestimmte Befehlsfolge auf Knopfdruck) 32
• Key Magic®(Das Programmieren von fehlenden Funktionen) 34
• Farbe & Helligkeit 35
PROBLEM & LÕSUNG 35
KUNDENDIENST 36
Inhaltsverzeichnis
Sie können mit Ihrer ONE FOR ALL 5 die Anzahl von vier Geräte Fernbedienen:
TV : Fernseher
VCR : Videorecorder
SAT : Satellitenempfänger oder Kabeldecoder
DVD : DVD
AMP : Verstärker / Tuner
Was die ONE FOR ALL 5 weiter so einzigartig macht, ist die „Lernfähigkeit“,
welches es möglich macht, spezielle Funktionen von Ihrer original
Fernbedienung auf die ONE FOR ALL 5 zu übertragen.
Auf den folgenden Seiten wird in einfachen Schritten erklärt, wie Sie die
ONE FOR ALL 5 auf Ihre Heimunterhaltungsumgebung benutzerspezifisch
einstellen können.
Wahrscheinlich werden Sie diese Bedienungsanleitung in der
Zukunft noch brauchen, bitte bewahren Sie es deshalb gut auf.
Über die ONE FOR ALL 5
Deutsch
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 19

20 WWW.ONEFORALL.COM
9
10
3
4
6
8
11
12/13
7
2
1
14
5
Ofa_5_Digital_Greek 31-08-2005 16:49 Pagina 20