ONESONIC BXS-HD1 User manual

BXS-HD1
User Manual

1 x BXS-HD1.
1 x USB Type C Cable.
1 x Charging Case.
1 x User Guide.
Packing List
In cases where any defects occur within 12 months from the date of
purchase, ONESONIC or their service partners will replace the unit with
a fully operational unit of the same type, or will provide a repair service
after inspection without charge for labour or parts. This excludes any
artificial damage. The earphones and packaging must be kept intact
and free of scratches.
Warranty
1. LED Indicator Light
2. Touch Control
3. Charging Pin and Microphone
4. Battery Level LED Indicator and Reset Button
5. USB Type-C Charging Jack
Product Functions
2

2
3
3
4
5
1

Low Battery A voice prompt alerts you that the
battery level is low. LED Indicator
flashes white every three seconds.
Charging Mode When charging the earphones
with the charging case, the LED
Indicator flashes white. When
charging is complete, the LED
Indicator turns off.
Bluetooth Pairing Mode The LED Indicator of the earphones
flashes white and blue alternately.
Bluetooth Connected The LED Indicator of the earphones
flashes blue slowly.
LED Indicator (Earphones)
4
LED Indicator (Charging Case)
Charging Mode LED Indicator flashes red. When
fully charged, LED Indicator will
turn solid white.
Case Battery Status (100%) LED Indicator 100% lit.
Case Battery Status (75%) LED Indicator 75% lit.
Case Battery Status (50%) LED Indicator 50% lit.
Case Battery Status (25%) LED Indicator 25% lit.
Case Battery Status (>10%) LED Indicator flashes red (fast).

Product Name ONESONIC BXS-HD1
Compatible Operating Systems Android/iOS
Chipset AB1356U
Bluetooth Version BT5.0 w/ support for HFP1.7,
A2DP1.3, AVRCP1.6, SPP1.2
Li-Battery Capability Earphone: 40mAh
Charging Case: 400mAh
Playing Time 3-4 Hours
Talking Time 3-4 Hours
Charging Time 1.5 Hours (Earphones)
1.5 Hours (Charging Case)
Charging Mode USB Type C 5V - 430mA
Fast Charge Enabled
Bluetooth Transmission Range 10m
Speaker Impedance 32 Ohms ± 15% @ 1kHz
Speaker Sensitivity (SPL) 115dB ± 2.7dB @ 1kHz
Product Specifications
5

Pairing Procedure
Ensure Bluetooth is switched on and activated on the device you wish
to pair with. Remove the earphones from the charging case. They are
automatically powered on when removed. A voice prompt alerts you
that power is on and the LED Indicators flash blue. Alternatively, the ear-
phones can be turned on manually by touching and holding the right and
left touch control panels. A voice prompt alerts you that power is turned
on. The LED Indicators flash blue.
Ensure Bluetooth is activated on the device you wish to pair with. Open
the Bluetooth devices list on your device and select ‘ONESONIC BXS-
HD1’. Click connect to start pairing procedure. If necessary, enter the
default pin code, ‘0000’. A voice prompt alerts you upon a successful
connection. Once connected, the blue LED Indicator will flash slowly.
Note: auto power on/off does not work when the charging case is out
of power. Earphones will turn off if they do not find a Bluetooth device
after 10 minutes.
6
Charging Procedure
A voice prompt alerts you that the battery level is low. The earphones
turn off automatically when power runs out. Insert the earphones into the
charging case. Close the lid and the earphones recharge automically. If the
LED Indicator on the charging case flashes red, it needs to be charged.
To charge the charging case, plug the USB-C cable into the charging port
of the charging case and connect the other end of the USB-C cable to a
power source. The LED indicator light on the charging case will show red
throughout the charging process. Once the earphones are fully charged,
the LED Indicator on the charging case will show solid white.
To reset/re-connect the left and right earphones, place them back into
the charging case and keep the lid open. Press and hold the Reset Button
on the charging case until the LED Indicator flashes white and red. This
resets the earphones and disconnects them from all paired devices. The
earphones can then be repaired. It is recommended to refresh the list
of bluetooth paired devices on your audio source, or Unpair/Forget the
‘ONESONIC BXS-HD1’ prior to repairing.
Resetting Your Earphones

Operating Instructions
Power On (Auto) Automatic power on once removed from
charging case.
Power On (Manual) Press and hold Touch Control for
2 seconds.
Power Off Automatic power off once inserted into
charging case and closed.
Power Off (Alternative) Automatic power off after 10 minutes with
no bluetooth connection.
Single Tap (Left) Decrease Volume
Single Tap (Right) Increase Volume
Single Tap (Left
or Right)
Answer Call
Double Tap (Left
or Right)
Play/Pause
Triple Tap (Left) Previous Track
Triple Tap (Right) Next Track
Hold (2 seconds) Left
or Right
End/Reject Call
Hold (2 seconds) Left
or Right
Turn on Voice Assist (Siri/Google)
7

Safety Information
Do not use the earphones at a high volume for extended periods as
hearing loss may occur. Check the volume of the earphones on your
paired device before playing any audio.
Do not use the earphones while driving or operating heavy machinery.
The use of earphones while operating a vehicle may be illegal in some
areas. Check and obey the applicable laws and regulations regarding
the use of earphones while operating a vehicle. Stop listening to
your audio device if you find it distracting while driving or operating
any type of vehicle.
Do not use this device if you find it disruptive to any activity that re-
quires your full attention to ensure personal safety.
Do not use the earphones while walking in dangerous areas where full
hearing capability is required for personal safety. Example areas include
but are not limited to: construction sites, while crossing the road, at
railway intersections etc.
The earphones and accessories may present a choking hazard or cause
other injury to small children and infants. Ensure that these devices are
stored carefully in an area away from small children.
With regular usage, earphones may lead to ear infections or skin irri-
tation. Clean the earphones regularly using a soft, lint-free cloth. Do
not get moisture in any of the openings or clean the product using
aerosols, solvents or abrasives. If skin irritation occurs, discontinue use.
If the problem persists, seek help from a qualified medical professional.
8