Onida S12gls-n4 User manual

The unit displayed is for representational purposes only. Actual unit may vary.

AIR CONDITIONERS

Warranty Registration System

Help us to serve you better by registering

your product for Warranty

- Web Registered at w

- Telephone

- Post / Visit Post the Warranty Registration Card &

ww.onida.com

Call Centre No. 0XX-39889000(0XX-STD Code of

State Capital) Service Centre

Copy or Visit the Nearest Service Centre.

Model: S09CFL-G3 / S12CFL-G3 / S18CFL-G3

Model: S12GLS-N4 / S18GLS-N4

cool

3 STAR 2 STAR

Dear customer

Congratulation on buying ONIDAAir Conditioner.

Your Air Conditioner comes with ONIDA Guarantee of Quality

as detailed in the manual.

ONIDA takes great pride in providing its customers with state-

of-the-art products that adheres to international quality

standards.

ONIDA is committed to following quality policy laid by our

chairman and managing director Mr. G. L. Mirchandani.

“We are committed to quality and strive for continuous

improvement through innovation and human development to

give customer better value for money always”

ONIDA stands committed to provide the ultimate customer

satisfaction, as nothing brings us greater joy than having

satisfied customers of ONIDA.

At ONIDA, feedback and suggestions based on your product

usage experience is greatly appreciated.

Please contact to us at r[email protected]

G. Sundar

Chief Executive Officer

IMPORTANT :

Please read this owner’s manual carefully and thoroughly

before installing and operating your room air conditioners.

Please retain this owner’s manual for future reference after

reading it thoroughly.

CONTENTSCONTENTS

Salient Features 1

Inside Overview Glossy Gold New 2

Inside Overview Color Flat Gold 3

Indoor Unit Display 4

Remote Overview 5

Operations 6

General Instructions for Installation 11

Installation Sketch 14

Installation of Model 15

Take care of your Air Conditioner 18

Precautions to be taken 19

Trouble Shooting 21

Installation and Satisfaction Report 23

Warranty Terms & Conditions 25

Preventive Maintenance Service Coupon 27

Warranty Card(Customer Copy) 29

Warranty Card(service Centre Copy) 31

List of service centre no.s in India 33

SALIENT FEATURES

0.8T / 1.0T / 1.5T Split Air Conditioner

Model Code:

S09CFL-G3 / S12CFL-G3 / S18CFL-G3

•Aesthetics:-

a) Unique Glossy Gold New Panel

b) Unique Color Flat Gold Panel

•Performance:-

a) Imported High BTU Compressor

b) Trapezoidal Inner Grooved Tube

c) Large L-Shaped Condenser Coil

d) High Technology 3 Star / 2 Star Energy Efficient.

•Features:-

a) Vertical Swing

b) Turbo

c) i-Cool

d) Auto-Restart

•Safety & Reliability:-

a) Gold Fins

b) Full Function LCD Remote

c) 5-Stage Epoxy Polyester Painting

d) Rugged Construction With Thicker Gauge Steel

S12GLS-N4 / S18GLS-N4 / 3 STAR

MODE H.SWING V.SWING

SLEEP

I-COOL

TIMERFAN

TURBO LOCK

MODE H.SWING V.SWING

SLEEP

I-COOL

TIMERFAN

TURBO LOCK

cool

INSIDE OVERVIEW

GLOSSY GOLD NEW INSIDE OVERVIEW

COLOR FLAT GOLD

nOUTDOORUNIT

Air in

Exhaust Air

Connection

pipe and

connecting wire

nOUTDOORUNIT

Air in

Exhaust Air

Connection

pipe and

connecting wire

nINDOORUNIT nINDOORUNITnINDOORUNIT nINDOORUNIT

Conditioned Air Out Conditioned Air Out

Return Warm Air In Return Warm Air In

Remote Controller Remote Controller

Front Panel Front Panel

Display Display

INDOOR UNIT DISPLAY

GLOSSY GOLD NEW DISPLAY

COLOR FLAT GOLD DISPLAY

Display on the indoor unit.

For the icon of LED windows, only relevant icons will light up with their displays on.

cool

SIGNAL RECIEVER TEMPERATURE DISPLAY

cool

SIGNAL RECIEVER TEMPERATURE DISPLAY

Temperature display Run Indicator

Cool Mode Indicator i-Cool Indicator IR Reciever

cool

REMOTE OVERVIEW

1. Open back cover and put 2 Nos. AAA size alkaline batteries.

2. Short one RESET piece after changing the batteries.

3. The remote signal can be reached up to six meters from the indoor unit.

4. When the button is pressed on remote, indoor unit will “beep” once, indicating

the receipt of signal. If no “beep” sound is heard, press the button once again.

5. Remove batteries if remote control has not been used for long time.

6. “*” Available in selected models only.

MODE H.SWING V.SWING

SLEEP

i-COOL

TIMERFAN

TURBO LOCK

SLEEP

HORIZONTAL SWING

VERTICAL SWING

LOCK / UNLOCK

i-COOL

BACK VIEW

RESET

CLOCK *

OPERATIONS

Operating Your Air Conditioner:

Your Split Air Conditioner can be conveniently operated using the intelligent cordless

remote control.

1. Switch on the MCB.

Press ON/OFF button on remote handset to switch ON the AC.

Your AC switches on with parameters that were set before power was switched

off. The unit receives the signal with "BEEP" tone and your AC starts operation.

Time Delay: To protect the compressor, a time delay is incorporated in the circuit.

The Time Delay ensures that the compressor switches ON only after a delay of about 3

minutes.

2. Press the Auto, Cool, Dry, or Fan mode by pressing “MODE" button.

3. Press the "FAN” button to set the fan speed.

Each press changes the fan speed from

Low-Med- High-Auto Fan speed.

The selected fan setting symbol can be

seen on the LCD.

4. The Set Temp. is displayed on LCD.

5. To switch off the AC, press the

same ON/OFF Button.

Setting the Desired Room Temp.:

You can set the temp. at which you would like your room to be.

Press " " button to increase the set temp. On every press, the temp. increases by 1 C.

Press " " button to decrease the set temp. On every press, the temp. decreases by 1 C

The two digit display shows the changing set temp. on LCD

The setting temp. range is from 16- 32 C.

OPERATIONS

Your split AC operates in one of four modes, COOL-DRY- . The modes button

cyclically chooses between these operating modes.

The AUTO Mode :

1. Press "MODE" button to cyclically step through the AUTO-COOL-DRY-FAN modes and stop

when AUTO mode is selected.

2. symbol can be seen on the Remote panel when you select the AUTO mode.

3. In this mode, the fan speed can be changeable.

4. Temperature can be pre-set in this mode, default temperature is 25 C.

5. In the AUTO mode, your AIR CONDITIONER "Thinks” for you.

The unit automatically and continuously monitors the difference between room temp. and

set temp. and adjusts the fan speed accordingly, to ensure maximum comfort.

The COOL mode:

In the cool mode, the compressor is in operation and your AC functions in the standard

operating mode, cooling your room to the desired set temp.

1. Press "MODE" button to cyclically step through the AUTO-COOL-DRY-FAN modes and

stop when cool mode is selected.

2. symbol can be seen on the Remote panel when you select the cool mode.

In this mode, you can change the temp. settings by pressing " " and “ ” temp.

buttons.

You can change the fan speed setting by pressing FAN button.

3. If the Room temp. is more than the set temp., then the compressor & outdoor FAN will

remain ON and perform the Cooling operation. If the room temp. achieves the temp. less

than set temp., then the compressor & outdoor FAN will remain OFF.

The DRY Mode:

In the DRY mode, your AC reduces the humidity within the room faster.

1. Press "MODE" button to cyclically step through the AUTO-COOL-DRY-FAN modes and

stop when DRY mode is selected.

2. symbol can be seen on the Remote panel when you select the DRY mode.

3. In DRY mode, Temperature and FAN Speed cannot change. Default pre-set temperature is

25 C. Indoor FAN will run at low speed. Compressor & Outdoor Fan work as per the

Temperature difference.

4. In this mode Horizontal swing is inactive, only Vertical swing is active.

AUTO- FAN

OPERATIONS

The FAN Mode:

1. Press "MODE" button to cyclically step through the AUTO-COOL-DRY-FAN modes and stop

when FAN mode is selected.

2. symbol can be seen on the Remote panel when you select the FAN mode.

3. In FAN mode, only Indoor FAN will run at set speed and Compressor & Outdoor Fan will

remain off. Temperature will be displayed on indoor unit as well as remote. Temperature

setting can be changed.

4. In this mode, you can change the Indoor FAN Speed.

TIMER Operation:

You can program your split AC to switch itself ON or OFF at particular time.

Maximum set time is 24 hrs, with 1.0 hr increment .

ON TIMER:

When the AC is "OFF" (in standby), press "TIMER" Button on remote to use this feature as the

TIMER. (make sure that MCB switch is "ON". The "TIMER" light on Indoor unit will glow ON.

For EXAMPLE:

Suppose you want to switch ON the AC after 8 hrs. Press "TIMER" button, when AC is in OFF

condition.

Press "TIMER" button to set ON timer. Display on Remote will show "8”.

OFF TIMER:

When the AC is "ON", press "TIMER" Button on remote to use this feature as

the TIMER. The "TIMER" light on Indoor unit will glow ON.

For EXAMPLE:

Suppose you want to switch OFF the AC after 8 hrs. Press "TIMER" button, when AC is in ON

condition.

Press "TIMER" button to set OFF timer. Display on Remote will show "8”.

CANCEL TIMER:

If you want to cancel either TIMER ON or TIMER OFF, press the TIMER button till the timer

becomes blank.

The FAN Mode:

OPERATIONS

Turbo MODE:

SLEEP Operation:

To switch on Sleep operation, Press "SLEEP" button once on remote.

Remote display will shows the “ “ symbol. After setting sleep mode, 5 seconds after

display will be goes off. In this mode, Fan speed will be in Low Speed only. After selection of

SLEEP Mode if you press fan speed button, fan speed will change as per the selection unless

it will be in low speed only.

In cool mode, after Sleep mode is set, your AC increases the set temp. by 1 C for every hour

that it operates,

After 2 hours and after the increase in set temp. by 2 C your AC maintains the temp. at that

level without further increase.

To cancel the Sleep mode, keep press the "SLEEP" button again.

LOCK Button: Press “LOCK” button to lock in all the current settings.

Remote display will shows the “ “ symbol. To release settings, press LOCK button again.

Pressing Turbo key on remote, remote will display symbol “ “ and activates the Turbo

function and air conditioner goes to powerful cooling. During this Mode temperature can be

changed and fan speed cannot be changed. In this mode the AC works on high fan speed.

Turbo mode will operational only in COOL mode. Press again Turbo button to cancel this

operation.

i-Cool:-

When you press i-cool button on remote, will be displayed on Indoor unit.

This mode is activated by pressing i-cool key on remote.

In this mode initially the AC start in special mode at super high speed designed to give

instant cooling and comfort. Compressor will start immediately in this mode. While AC is in

this mode temp, Fan Speed, Timer, Sleep keys are inactive and these parameters cannot be

changed.

To quit i-cool mode Press MODE or TURBO Button.

cool

1110

OPERATIONS

SWING Operation:

Your split AC has oscillating louvers for uniform cooling around your room.

You can stop the oscillation if you so desire.

Up/Down Air Direction Adjustment:

Press the “H.SWING” button to adjust the Air flow direction UP / Down for continuous

swing “ “ shows on remote LCD.

Press the “H.SWING” button Twice to keep louver at desired position, remote LCD

shows “ “.

VERTICAL SWING Button:

To adjust the left/right air louver direction

press V.SWING button.

Emergency Operation Switch:

In case the batteries in the remote are worn out, or remote is faulty or missing, use

emergency operation switch (*) to ON/OFF AC.

In Emergency operation unit will run at preset temperature of 25 C and in AUTO Mode.

To access emergency switch, open the grill as

shown in the figure.

GENERAL INSTRUCTIONS FOR

INSTALLATION

Locating the indoor and outdoor units

properly will help optimise the performance of

your airconditioner. While your Onida /

Dealer's Technician will be happy to guide you

on the best location for your airconditioner,

here are a few helpful hints.

Locatingthe IndoorUnit

• Locate the IDU for the best cool air

circulation. Preferably, there should be

no obstructions nearby, as shown in the

adjacent figure.

• Do not locate the unit directly opposite a

door which is opened frequently. The

cold air will go out of the room each time

the door is opened, as shown in the

adjacent figure.

• All indoor units will form condensate water.

Please ensure that the condensate can

be drained out of the room to a toilet /

pantry, etc. The installation engineer will

make sure that a "U" bend is provided in

the drain to prevent insects from coming

into the room through the drain tube, as

shown in the adjacent figure.

1312

GENERAL INSTRUCTIONS FOR

INSTALLATION

LocatingtheOutdoorUnit

The outdoor unit houses the compressor,

condenser fan and electrical components.

The heat removed from the room is expelled

to the atmosphere through the outdoor unit.

Once again, the Onida / dealer's Technician

will ensure optimal installation of the ODU for

you. However, the following information will

be of interest to you.

• The Outdoor Unit can be mounted on a

wall, sunshade or skirting.

• Ideally, the ODU should not be too

far a w a y f r o m t h e I D U ; t h e

recommended distances are

marked in the adjacent figure.

• Ensure that air can pass freely through

the unit. Please allow at least 2 meters

free space on the air outlet side, and 0.3

meters on the air inlet side.

• If more than one ODU is to be installed,

they must be properly separated, so that

the warm air from the outlet of one does

not enter the inlet of the other.

• Avoid long and complicated routing

between the IDU and ODU, as

shown in the three adjacent figures.

• Too long

• Too high

• Too many bends

• The ODU must be placed on strong

frame or support. If mounted on a

wall, please ensure that the wall is

thick enough and that the frame is

supported adequately.

• Finally, it is most important for the

ODU to be easily accessible to the

service engineer. It is advisable to

discuss the same with the engineer

before deciding upon the location of

the unit.

If the ODU is to be located on a high

ledge, adequate space must be

provided for the service engineer to

service the unit. It is a good idea to

provide a catwalk (a platform)

around the unit and access door /

window to the Unit.

Electricaloutlet

After the location of the outdoor unit and

indoor unit is finalised, you must provide

a suitable electrical outlet near the

indoor unit.

GENERAL INSTRUCTIONS FOR

INSTALLATION

MCB

To ODU

STABILISER

To ODU

1514

INSTALLATION SKETCH

Remote Controller

15cm right

15cm left

15cm above

Loop the

connective

cable.

60cmabove

60cm above

30cmabove

Air FilterAir Filter

Air Outlet

30cmabove

Wrapping tape

200cmabove

Additional drain pipe

MODE H.SWING V.SWING

SLEEP

i-COOL

TIMERFAN

TURBO LOCK

INSTALLATION

nDrillonthewall

Confirm the position of holes and drill holes of diameter 65 mm on the wall

nINDOORUNIT

1. Fitment of mounting plate

The mounting plate should be fitted on the structural part of wall on which indoor unit

is to be installed.

2. Drill two holes at a distance of 450 mm between them for the expansion bolts.

nConnectingofcables

1. Open the front panel

2. Dismantle the electric box cover

and fastener

3. Connect the cable

4. Reassemble the fastener and electric box

cover.

150mm or more to ceiling

Indoor unit outline Installation plate

293

Right rear side

refrigerant

pipe hole 65

Left rear side

refrigerant

pipe hole 65

120mm or more

to wall

120mm or more

to wall

995

Blue

Terminal board

Power connection wire

Black Yellow-green

Center of Hole(Ø65mm)

Insert Ruler

180mm

Align Ruler with straight line

S.No.

Name of Accessories

Installation Plate

Clip Anchor

Self-tapping Screw A ST3.9X25

Seal

Drain Joint

Connecting

Pipe

Assembly

Liquid Side

Gas Side

6.35 (9000Btu/h, 12000Btu/h,

18000Btu/h Models)

9.53 (9000Btu/h Model)

12.7 (12000Btu/h,18000Btu/h)

Remote Controller

Q’ty

Parts you

must

Purchase

1716

INSTALLATION

nInstallationof indoorunit

After putting the pipe assembly through

the wall, attach the indoor unit to the

mounting plate on the wall as shown in

the figure.

nInstallationof outdoorunit

• The connecting cables must be clipped together.

• Special cable to be used to connect indoor unit and outdoor unit.

• The electric box cover must be mounted on its position on outdoor unit.

nConnecting of pipes

nSealing the wall hole and clamping the pipe

• Use putty to seal the wall hole.

• Use pipe fastener to clamp the pipe on wall

1 2(N) 3 4

12(N)

External connection

electric wire

Liquid side piping

Liquid side

piping insulation

Water

drainage

pipe

Finally wrap it

with tape

Gas side

piping insulation

Gas side piping

air proof with putty

Mounting Board

Fixing Hook

INSTALLATION

nDischarge the air of the units:

It can used as vaccum pump.

Remove screw cap of closing valve and

gas charging hole; Open the closing valve

with Allen wrench(turn 90 clockwise),

then push the gas hole for about 10 seconds,

(When a gas like fog appears, it indicates

that the air of unit has been discharged)

put back the screw cap of gas charging hole.

Do the leak test with leak detector or soap water.

nAddrefrigerant

• If the connecting pipe is longer than 7 meters, add refrigerant as needed. Add

amount A= (Lm-7m) 15g/m.

(A: add refrigerant amount, L: the length of connecting pipe)

• Add refrigerant with the spring balance, as specified above.

the length of connecting pipe (m) 7 8 9 10

add amount (g) 0 15 30 45

nTest

• Proceed leak test (with leak detector or soap water.) and inspect connecting

cables before test operation.

Test procedure: (Control by emergency operation switch or remote

controller) For detailed operation, see OPERATION OF AIR CONDITIONER

in the manual.

Indoor unit Liquid pipe

Gas pipe Gas charging hole

Closing valve

connecting pipe

Bottle of storage refrigerant

Bottle’s valve of storage refrigerant

Outdoor unit

Gas

Charging

Hole

Screw Cap

Gas connecting

pipe

Liquid connecting pipe Cap

Liquid closing valve

Gas closing

valve

Allen Wrench

TAKE CARE OF YOUR

AIR CONDITIONER

Most of the maintenance work on your air

conditioner, during warranty and

subsequently under the maintenance

contract, will be handled by a trained

technician. However, there are some simple

maintenance jobs that you, as a user, should

carry out on your own.

• Lift the cover by applying gentle

pressure on both sides and lift it

upwards

• The filters will be visible

• Lift the filters slightly upwards

• Pull out the filters

• Wash the filters under a tap until

they are clean

• Do not use detergents for cleaning

the filter.

PRECAUTIONS TO BE TAKEN

Do's ( )

• Seal all air gaps in the room

• Choose the right temperature to avoid over cooling

• Ventilate the room regularly.

• Switch off the power supply if not in use for long.

• Unplug the unit while cleaning.

Don't's ( )

• Don't leave the doors and windows open when the air conditioner is on.

• Don't use hot water to clean your front grill

• Don't use scouring powder, harsh soaps, wax or polish on the grill.

• Don't switch on the air conditioner immediately after switching it off.

Wait for 2 minutes.

• Don't operate with a clogged filter

• Don't block air intake & outlet vents

• Don't change setting unnecessarily.

2120

TROUBLE SHOOTING CHART

Suggested Remedy

Note: If the unit still does not work, or if any other types of symptoms are encountered,

shut off the mains (switch fuse unit) and call the service engineer.

Reset MCB

Replace fuse wire

If the input voltage to

the stabiliser is below

the acceptable range,

the AC will not operate

Press the On/Off key

on the control panel or

the remote

Remove all

obstructions to make

the airflow paths free

Change to COOL

mode

Make the selected

temperature less than

room temerature

Clean the air-filter

MCB has tripped

Fuse has burnt

Input voltage to the

stabiliser is below

acceptable range

The On/Off key is not

pressed

The airflow paths are

not free

The Units is in the fan

mode

Selected temperature is

more than room

temperature

Air-filter is not clea

Possible Causes

Unit does not start

Units does not cool

(Even after the normal

Time Delay of approx.

2/3 minutes for

compressor to start)

Symptoms

2322

Customer Name :

Address

Phone[O] [R]

Unit Model Unit Serial Number Dealer Name

Invoice Number Date of Purchase Date of Installation

MCB Rating Current (Amps.)

Cable Size Ambient Temp. ( C)

Earthing Room Temp. ( C)

Stabiliser Grill Temp. ( C)

Input Voltage Remote Operation

Customer's Response : To be filled up by the Customer

1.Installation completed within:

12hrs( ), 24 hrs( ) , 36 hrs ( ), more than 36 hrs ( )

2. How did you find the behavior of the Engineer :

Excellent ( J), Good ( K), Not satisfied ( L)

3. Overall rating of the service:

Excellent ( J), Good ( K), Not satisfied ( L)

4. Suggestion if any:

Job Number Engineer's Signature Customer's Signature

INSTALLATION & SATISFACTION

REPORT

2524

M/S. MIRC ELECTRONICS LTD, WARRANTS THIS ONIDA AIR CONDITIONER[(except the front grill,

knobs, remote unit and add-on plastic parts) TO THE ORIGINAL PURCHASER TO BE FREE FROM

DEFECTS IN MATERIALS AND WORKMANSHIP WITHIN ONE YEAR FROM THE DATE OF PURCHASE

AS PROVIDED IN THE WARRANTY REGISTERATION CARD.

WARRANTY FOR COMPRESSOR:

MIRC ELCTRONICS LTD, HEREAFTER WARRANTS TO THE PURCHASER OF THIS ONIDA AIR

CONDITIONER THAT FOR A PERIOD OF SIXTY MONTHS FROM THE DATE OF INVOICE .

WE WILL REPAIR/REPLACE THE COMPRESSOR WHICH PROVES UPON INSPECTION BY US OR ANY

OF OUR AUTHORISED SALES DEALERS TO HAVE BEEN DEFECTIVE DUE TO MANUFACTURING

DEFECT.

This warranty is subject to terms and conditions as mentioned below:

1. This warranty shall be valid only for the said period of 12 months as specified above, irrespective of

whether the said unit has been in use or not for any reason whatsoever, or the unit is moved from one

location to another. Warranty does not cover accessories external to the equipment.

2. The warranty period specified above shall include time taken for repairs, replacements, break-downs,

transit time etc. No notice of expiry period of warranty will be given by the company.

3. This warranty shall stand automatically terminated in the event of the said unit being serviced,

repaired, installed, de-installed, re-installed or otherwise attended to by any person or organization or

agency or by the said purchaser himself other than the authorized representative of the company.

4. Parts of the unit replaced or repaired under the terms of this warranty are warranted only for the

remaining period of the original warranty period.

5. For attending any service call under this warranty beyond the municipal limits of the locality in which

the authorized representative/dealer is situated (outstation locations), all to and fro travelling and

other incidental expenses as prevailing from time to time incurred in connection with the visit of the

service personnel, technicians, etc shall be borne by the said purchaser and shall be payable in

advance. Additionally, all expenses incurred by the authorized representative /dealer in collecting the

said unit or any part thereof from such outstation locations and its return to the original location shall

be borne by the said purchaser.

6. Any loss of refrigerant caused due to sabotage, improper handling or treatment , carelessness,

accident, fire, flood earthquake or any natural calamity any corrosive action on the original refrigerant

pipes, fittings, valves etc for whatever reasons, shall not be covered under this warranty.

7. In the event of any change in the location of the unit during the warranty period, this warranty shall

become null and void unless the fact of the proposed change is communicated in writing to the

authorized dealer at least seven (7) days prior to the said change. On receipt of such information the

authorized dealer or any of its counterparts shall arrange for de-installation of the said unit on

chargeable basis. However, in the event of any damage occuring to the unit or to any of its parts during

the course of its transit by the said purchaser, repair or replacement, the said unit or any part thereof

damaged shall not be covered by this warranty.

WARRANTY TERMS

AND CONDITIONS

2726

8. It shall be the absolute discretion of the company to a) effect the repairs or replacement of parts

whether at the site of installation or at any service centre, and b) have the job attended to either by the

Company's service personnel or its authorised dealer

9. This warranty is in the nature of and for the purpose of set forth herein above and in particular the

Company shall not in any event be liable for direct, indirect, incidental or consequential loss or

damages to either the said purchaser and /or his property or any other third party.

10. The AC is designed to operate at a range (230V +/- 10%). Any failure due to operation of the machine

beyond these limits will not be covered by the above warranty.

Customer shall ensure that a stabilizer is installed in those areas where voltage is not available within

the warranty range (230V +/- 10%). The stabilizer should be of any reputed manufacturer, tested and

recommended by the Company.

11. The purchaser should preserve the original invoice for necessary verification and produce, as and

when required.

12. Warranty null and void if:

i. The Air Conditioner is not purchased from the authorized dealers of the company.

ii. The Service Centre copy of warranty card is not received within 10days of date of purchase at the

nearest Authorised Service Centre.

iii. Any damage is caused by accident, mishandling, tampering with installation, or negligence in

following instructions of the user manual issued by Company.

iv. Any damage is caused by improper electrical circuit outside the unit or by any defective electrical

supply

v. At any time, during the warranty period if any part of the unit is tampered with, altered, repaired or

serviced by any unauthorized person, not being the authorized representative of the company or

its authorized dealers

vi. The serail number of the unit or any part thereof is damaged , defaced, altered, obliterated , or

tampered with or removal for any reason whatsoever

viii. The unit is unauthorisedly moved from its original place of installation or re-installation

13. None of the employees and /or Authorized Dealers of the Company have any authority whatsoever to

vary the terms and conditions of this warranty.

14. This warranty shall be deemed to have been issued at Mumbai, state of Maharashtra and courts at

Mumbai shall have exclusive jurisdiction on matters covered by or following from this warranty, and

the original purchaser alone shall have cause of action arising out of the transaction.

Preventive Maintenance Service 1 Date: ________

Customer Identification Number: ___________________________________________

Name of the customer: ____________________________________________________

Installation address: ______________________________________________________

________________________________________________________________________

Phone: _________________ Mobile: __________________ Fax: ________________

E-mail: _________________________________________________________________

Unit model: ____________________________ Serial Number: __________________

Service report number: ___________________________________________________

Customer's Signature: _______________________ Name: _______________________

Preventive Maintenance Service

Customer Identification

Number:

______________________

Unit Model: ___________

Sr. No: _______________

Name of Serviceman:

______________________

Date: ______ Time: _____

Sign. of Serviceman

Preventive Maintenance Service 2 Date: ________