Onida W182flt User manual

The unit displayed is for representational purposes only. Actual unit may vary.

Warranty Registration System

Help us to serve you better by registering

your product for Warranty

Web Register at w

Telephone

Post / Visit Post the Warranty Registration Card &

ww.onida.com

Call Centre No. 0XX-39889000(0XX-STD Code of

State Capital)

Service Centre

Copy or Visit the Nearest Service Centre.

Model: W182FLT / W183FLT

3 STAR 2 STAR

Dear customer

Congratulation on buying ONIDA Air Conditioner.

Your Air Conditioner comes with ONIDA Guarantee of Quality

as detailed in the manual.

ONIDA takes great pride in providing its customers with state-

of-the-art products that adheres to international quality

standards.

ONIDA is committed to following quality policy laid by our

chairman and managing director Mr. G. L. Mirchandani.

“We are committed to quality and strive for continuous

improvement through innovation and human development to

give customer better value for money always”

ONIDA stands committed to provide the ultimate customer

satisfaction, as nothing brings us greater joy than having

satisfied customers of ONIDA.

At ONIDA, feedback and suggestions based on your product

usage experience is greatly appreciated.

Please contact to us at r[email protected]

Chief Executive Officer

IMPORTANT :

Please read this owner’s manual carefully and thoroughly

before installing and operating your room air conditioners.

Please retain this owner’s manual for future reference after

reading it thoroughly.

Dr. Y. V. Verma

CONTENTS

Salient Features 1

Control Panel 3

Remote Overview 4

Operations 5

Safety Precautions 11

Installation 13

Electrical Requirements 17

Take care of your Air Conditioner 18

Precautions to be taken 19

Trouble Shooting Chart 21

Installation and Satisfaction Report 23

Warranty Terms & Conditions 25

Preventive Maintenance Service Coupon 27

Warranty Card(Customer Copy) 29

Warranty Card(service Center Copy) 31

Inside Air Conditioner 2

SALIENT FEATURES

1.5T Window Air Conditioner

W182FLT / W183FLT

a) 3 Star / 2 Star Energy Saver BEE Rated

d) Full Function LCD Remote

e) Gold Fin

Model Code :

• Aesthetics:-

a) Unique Flat Panel

• Performance:-

b) High BTU Compressor

c) Trapezoidal Inner Grooved Tube

d) Large Condenser Coil

• Features:-

a) Combined Timer

b) Auto-Restart

c) Multi Fan Speeds

• Safety & Reliability:-

a) Low Deration Factor

b) Hydrophilic Fins for Evaporator

c) 5-Stage Epoxy Polyester Painting

d) Rugged Construction With Thicker Gauge Steel

CONTROL PANEL

INSIDE THE AIR

CONDITIONER

1. Front panel

2. Air filter

3. Frame

4. Cabinet

5. Air inlet grill (outdoor side)

6. Air outlet grill

7. Electronic control keypad

8. Power supply cord

9. Remote control

FEATHER TOUCH:

1. “Power” Key

ŸPower button to ON/OFF the Air Conditioner.

2. “Mode” Key

ŸToggles between Auto/Cool/Dry/Fan Modes.

3. “Temp/Timer Adjustment” Key

ŸAdjust the temperature/timer setting.

4. “Fan Speed” Key

Ÿ Toggles the Fan speed between High, Low and Auto.

5. “Remote Sensor”

6. “Room Temp Display”

7. “Timer” Key

Ÿ Toggles between Timer ON and Timer OFF.

8. “Swing” Key

Ÿ To adjust the airflow direction.

The unit displayed in manual are for representational purpose only. Actual unit may vary.

POWER

TEMP

TIME

HIGH

MID

LOW

DRY

FAN

COOL

MODE

SWING

ON/OFF

TIMER

ON/OFF

SPEED

FAN

Accessories

Seal

(Used on

drain joint)

Screw

Drain Joint

1 pec

Water outlet pipe

1pec

Drain Tray

MODE SWING

SLEEP

TIMERFAN

REMOTE OVERVIEW OPERATIONS

1. Open back cover and put 2 Nos. AAA size alkaline batteries.

2. The remote signal can be reached up to six meters from the Air Conditioner Receiver.

3. When the button is pressed on remote, Unit will “beep” once, indicating the receipt of

signal. If no “beep” sound is heard, press the button once again.

4. Remove batteries if remote control has not been used for long time.

5. Heat mode is not available with all models.

Operating Your Air Conditioner:

Your Window Air Conditioner can be conveniently operated using the intelligent cordless

remote control.

1. Switch on the MCB.

Press ON/OFF button on remote handset to switch ON the AC.

All icons will glow once.

Your AC switches on with parameters that were set before power was switched

off. The unit receives the signal with "BEEP" tone and your AC starts operation.

Time Delay: To protect the compressor, a time delay is incorporated in the circuit.

The Time Delay ensures that the compressor switches ON only after a delay of about 3

minutes.

2. Press the “MODE” Button for Auto, Cool, or selection.

3. Press the "FAN” Button to set the Fan Speed. Each press changes the fan speed

from Low- Med - High Fan speed. The selected fan setting symbol can be

seen on the LCD.

4. The Set Temp. is displayed on LCD, Press button ” “ to increase and “ “ to the

decrease the temperature.

5. To switch off the AC, press the same ON/OFF Button.

Setting the Desired Room Temp.:

You can set the temp. at which you would like your room to be.

Press " " button to increase the set temp. On every press, the temp. increases by 1 C.

Press " " button to decrease the set temp. On every press, the temp. decreases by 1 C

The two digit display shows the set temp. on LCD.

The setting temp. range is from 16- 32 C.

Dry Fan

Your window AC operates in one of four modes, AUTO-COOL-FAN-DRY. The modes

button cyclically chooses between these operating modes.

*Cooling capacity measured at High speed, as per IS 1391:1992 Part 1

Signal ejecting window

MODE SWING

SLEEPTIMERFAN

SLEEP

SWING

BACK VIEW

RESET

CLOCK *

OPERATIONS OPERATIONS

Your Window AC operates in one of four modes, COOL-DRY- . The modes button

cyclically chooses between these operating modes.

The AUTO Mode :

1. Press "MODE" button to cyclically step through the AUTO-COOL-DRY-FAN modes and

stop when AUTO mode is selected.

2. symbol can be seen on the Remote panel when you select the AUTO mode.

3. In this mode, the fan speed can be changeable.

4. Temperature can be pre-set in this mode, default temperature is 25 C.

5. In the AUTO mode, your AIR CONDITIONER "Thinks” for you.

The unit automatically and continuously monitors the difference between room temp.

and set temp. and adjusts the fan speed accordingly, to ensure maximum comfort.

The COOL mode:

In the cool mode, the compressor is in operation and your AC functions in the standard

operating mode, cooling your room to the desired set temp.

1. Press "MODE" button to cyclically step through the AUTO-COOL-DRY-FAN modes and

stop when cool mode is selected.

2. symbol can be seen on the Remote panel & LED will glow on display panel when

you select the cool mode.

In this mode, you can change the temp. settings by pressing " " and “ ” temp.

buttons.

You can change the fan speed setting by pressing FAN button.

3. If the Room temp. is more than the set temp., then the compressor will remain ON

and perform the Cooling operation. If the room temp. achieves the temp. less than set

temp., then the compressor will remain OFF.

The DRY Mode:

In the DRY mode, your AC reduces the humidity within the room faster.

1. Press "MODE" button to cyclically step through the AUTO-COOL-DRY-FAN modes and

stop when DRY mode is selected.

2. symbol can be seen on the Remote panel & LED will glow on display panel when

you select the DRY mode.

3. In DRY mode, Temperature and FAN Speed cannot change. Default pre-set

temperature is 25 C. FAN will run at low speed. Compressor work as per the

Temperature difference.

AUTO- FAN The FAN Mode:

1. Press "MODE" button to cyclically step through the modes

and stop when FAN mode is selected.

2. symbol can be seen on the Remote panel & LED will glow on display panel

when you select the FAN mode.

3. In FAN mode, only FAN will run at set speed and Compressor will remain off.

Temperature will be displayed on display panel. Temperature setting can be

changed.

4. In this mode, you can change the FAN Speed.

TIMER Operation:

You can program your AC to switch itself ON or OFF at particular time.

Maximum set time is 24 hrs, with 1.0 hr increment .

ON TIMER:

When the AC is "OFF" (in standby), press "TIMER" Button on remote to use this feature as

the TIMER. (make sure that MCB switch is "ON". The "TIMER" light on Display panel will

glow ON.

For EXAMPLE:

Suppose you want to switch ON the AC after 8 hrs. Press "TIMER" button, when AC is in

OFF condition.

Press "TIMER" button to set ON timer. Display on Remote will show "8”.

OFF TIMER:

When the AC is "ON", press "TIMER" Button on remote to use this feature as

the TIMER. The "TIMER" light on Display panel will glow ON.

For EXAMPLE:

Suppose you want to switch OFF the AC after 8 hrs. Press "TIMER" button, when AC is in

ON condition.

Press "TIMER" button to set OFF timer. Display on Remote will show "8”.

CANCEL TIMER:

If you want to cancel either TIMER ON or TIMER OFF, press the TIMER button till the

timer becomes blank.

AUTO-COOL-DRY-FAN

OPERATIONS

NOTE: Upto 10 hrs, setting time increment will be 0.5 hrs, after 10 hrs setting time

increment will be 1 hrs.

SLEEP Operation:

To switch on SLEEP operation, Press SLEEP button on remote.

In this mode, the set temperature will increase by 1 C over the next 1hour and by another

2 C after an additional 1 hour. This new temperature will be maintained for 5 hours

before it returns to the original selected temperature. Then unit will goes off.

Press again to cancel SLEEP operation.

NOTE:- The SLEEP function is only available under COOL and AUTO Modes only.

SWING Operation :

Press “SWING” button to adjust the airflow direction.

Press it again to stop.

OPERATIONS

Vent Control

CLOSE VENT OPEN CLOSE OPEN

Vertical air flow adjustment (manually)

The Vent control is located above the control knobs. The operation is different

on different models (see below figures).

For maximum cooling efficiency, CLOSE the vent. This will allow internal air circulation.

OPEN the vent to discharge stale air.

To open the vent, pull the lever toward you To open the vent, set the lever to the right

position.To close it, push it in. To close it, set the lever in the left position.

To adjust vertical air flow direction, adjust any one of the

horizontal louver blades. When adjusting the horizontal

louver blades up and down, always keep the top or bottom

blades horizontal. This can effectively prevent water droplets

condensing on the front panel of the unit.

1110

SAFETY PRECAUTIONS

Plug in the power plug

properly.

Do not operate or stop the

unit by inserting or pulling

out the power plug.

Do not damage or use an

unspecified power cord.

Otherwise , it wil l caus e electric

shock or fire due t o heat

generatio n o r electrica l shock.

I t wil l cau s e electrica l shock or fire

due to hea t generation.

It will cause electrica l shock or fire.

I f th e supply cor d is damaged , it

must be replaced by a specia l cord

or assembly availabl e fro m the

manufacture r or its servic e agent.

Do not modify power cord

length or share the outlet

with other appliances.

Do not operate with wet

hands or in damp

environment.

Do not direct airflow at room

occupants only.

I t wil l c ause electrica l shock or

fire due to hea t generation.

It ma y cause electrica l shock.

Thi s coul d damag e you r health.

Never touch th e metal parts

of th e uni t when removing

th e filter.

Do not clean the air

conditioner with water.

Ventilate wel l when used

together wit h a stive , etc.

I t may cause a n injury. Wate r may enter th e uni t and

degrad e th e insulation . I t may

caus e a n electri c shock.

An oxyge n shortag e may occur.

To prevent injury to the user or other people and property damage, the following instructions must

be followed.

ŸIncorrect operation due to ignoring of instruction will cause harm or damage, the seriousness is

classified by the following indications.

SAFETY PRECAUTIONS

When cleaning the unit , first

mak e sur e th e power and

breaker are turned off.

Do not put a pet or house

plant wher e it wil l be

exposed to direct air flow.

Do no t us e fo r special

purposes.

Sinc e th e fa n rotate s a t high

spee d durin g operation, i t may

caus e a n injury.

Thi s coul d injure th e pe t or plant. D o not us e thi s ai r conditione r to

preserv e precisio n devices , food,

pets, plants , an d ar t objects.

I t ma y caus e deterioration of

quality, etc.

Do no t operate Switches

wit h we t hands.

Do no t apply an insecticide

or flammable spray.

Do no t put a heater, etc.

where is exposed to direct air

flow.

I t may cause a n electri c shock. I t may cause a fire or deformation

of the cabinet.

I t ma y cause imperfect combustion.

1312

INSTALLATION

Over 50cm

About 10mm

FENCE

AWNING

75-150cm

Over 50cm

About 10mm

FENCE

AWNING

75-150cm

All side louvers of the cabinet must remain exposed to the outside of the structure.

CAUTION

Select the best location

1. To avoid vibration and noise, make sure the unit is installed securely and firmly.

2. Install the unit where the sunlight does not shine directly on the unit.

If the unit receives direct sunlight, build an awning to shade the cabinet.

3. There should be no obstacle, such as a fence or wall, withing 50cm from the back of the

cabinet because it will prevent heat radiation of the condenser.

Restriction of outside air will greatly reduce the cooling and heating efficiency of the air

conditioner.

4. Install the unit a little obliquely outward not to leak the condensed water into the room

(about 10mm or 1/4 bubble with level).

5. Install the unit with its bottom portion 75~150cm above the floor level.

6. The power cord must be connected to an independent circuit. The yellow/green wire must

be grounded.

Installation of the Housing

Step 1

Remove the air conditioner from it’s packaging, remove fixing screws and slide the air

conditioner out of it’s housing (Refer to installation Steps).

Step 2

Prepare the hole in the wall so that the bottom of the housing is well supported, the top

has minimum clearance and the air inlet louvers have clearance as shown below in

options A and B. Holes from the outside through to the cavity should be sealed. The

housing should slope down towards the rear by about 5mm to allow water formed during

operation to drain.

Step 3

Install the housing into the wall and secure. Ensure the foam seals are not damaged.

Flash, seal or fill gaps around the inside and outside to provide satisfactory appearance

and protection against the weather, insects and rodents.

NOTE: UNIT MAY BE SUPPORTED BY A

SOLID FRAME FROM BELOW OR

BY A HANGER FROM A SOLID

OVERHEAD SUPPORT.

Preferred method of installation into a timber

framed wall, partition or window.

FLASH OR SEAL AROUND EXTERNAL

WALL FRAME OR ARCHITRAVE

STURDY TIMBER

FRAME ALL ROUND

UNIT

TIMBER FRAMED

WALL OR PARTITION

EXTERNAL SUPPORT

FRAME AT BALANCE

POINT OF A/C

ALTERNATIVELY, BRACKETS

AS ILLUSTRATED BELOW

MAY BE USED.

DRAIN PAN

INSTALLATION

1514

INSTALLATION

AIR IN

AIR OUT

100mm minimum

OPTION A

AIR IN

LOUVRE

BRICK

WALL

45 BRICK CUT AWAY

TO CLEAR LOUVRES

FRONT

AIR OUT

AIR INAIR IN TOP

VIEW

45 BRICK CUT AWAY

TO CLEAR LOUVRES

100mm

BRICK

WALL

100mm

OPTION B

Installation of the unit into the Housing

Installations of the unit into the wall

Alternative method of installation if external

support cannot be provided.

FLASH OR SEAL AROUND EXTERNAL

WALL FRAME OR ARCHITRAVE

STURDY TIMBER

FRAME

TIMBER FRAMED

WALL OR PARTITION

SOLID TIMBER SUPPORT

STEADYING BRACKET

(ONE PER SIDE)

DRAIN PAN

ENSURE LOUVRES

ARE ENTIRELY

OUTSIDE THE WALL

INSTALLATION

Installation Steps

1. Slide the unit into the housing until it is firmly against the rear of the housing. Care is required

to ensure the foam sealing strips on the housing remain in position.

2. Connect the air conditioner to the power and position excess cord length beneath the air

conditioner base.

3. Engage the chassis fixing brackets into the bottom housing rail and secure to the base with

the screw provided.

4. Remove the front panel from it’s carton and plastic bag and fit as per the installation

instruction.

5. Switch unit on. Check for operation of the unit and check for vibration in the installation.

6. Fit the drain pan to the housing and run a drain line to a suitable location if required.

Pull out the Air-return

grids,and remove three

screws on the front

board,then take off the

front board

Remove the two screws

at the bottom or on

both sides of the

package.

Hold the handle of the

base of the air conditioner

firmly and pull the base

from the package along

with all the machine parts

Fix the outer case of the air conditioner to the installation

supports with screws

(supplied by the end-user or by the local our Co. dealer or

authorized service center).

6. Push the air conditioner into the outer case horizontally.

7. Install the base fixing plate(optional), tighten the two

screws at the bottom or both sides of the outer case.

8. Install the front board .

9. Install the air-return grids.

10. Test running.

a) Connect to power source.

b) Check to see if the room temperature control and the function controls work properly.

c) Check if the water drainage is smooth and unblocked.

d) Check if there are any abnormal sounds during operations.

Remove the base fixing

plate (optional steps,The

base fixing plate is not

contained on some

models)

(Figure 1) (Figure 2)

(Figure 3) (Figure 4)

(Figure 5)

(Figure 6)

1716

INSTALLATION ELECTRICAL

REQUIREMENTS

Electrical requirements

• Wiring up to the location of the air conditioner should be as under :

- 7/20 gauge

• The MCB for the air conditioner should not be rated less than 20 Amps.

• The meter to which your air conditioner line is connected, should have at least a

20 Amp. rating

• Wire ends should be tightened fully.

• Your air conditioner operates at a voltage of 230 V AC ± 10%. In case your area

experiences voltage fluctuation please use a suitable voltage stabiliser, as per the

table below :

Tonnage of your Voltage Stabilizer

Air conditioner Rating

1.0 T

on 3 KVA

1.5 Ton 4 KVA

The unit displayed in manual are for representational purpose only. Actual unit may vary.

(Figure 1-1).

(Figure 1-2).

(Figure 1-3).

Drainage hole

Sealing ring

Water outlet tube

Rubber stopper

Drainage hole

Rubber stopper

Water containing plate

Screws

Extended water tube

Water outlet tube

Treatment of condensing water

There are two ways to handle the condensing water.

Please make your choice according to your needs.

Treatment of condensing water

Method I:

Block the drainage hole on one side of the unit base

with a rubber stopper so as to let the condensing

water flow out from the rear drainage hole of the unit.

(as shown in Figure 1-1)

a) When this method is adopted, the condensing

water in the base plate cannot be drained completely.

The remaining water may improve the heat dispersing

effect of the unit, but with louder noise.

b) Installation of drainage tube: Install the sealing ring

to the drainage tube and align the tube with the rear

drainage hole of the unit, and turn the water outlet

connecting tube for 90 degrees and then clamp it

firmly (Figure 1-2).(Figure 1-1).

Method II:

The condensing water flows out from the drainage

hole at the base plate of the unit

a) When this method is adopted, the condensing

water in the base plate can be drained completely,

which helps to prevent from rusting. There will be no

noise of water splashing. But the air conditioner has to

be raised to a certain height in installing so that the

water containing plate can be placed between the

base of the unit and the supporting platform.

b) Installation of the water containing plate: Use a

rubber stopper to block the drainage hole at the rear

of the unit and place in the water containing plate

(Figure 1-3).

1918

TAKE CARE OF YOUR

AIR CONDITIONER

Air Filter

Drainage

SEAL

DRAIN

JOINT RUBBER

PLUG

The air filter behind the inlet grill should be checked and

cleaned at least once every 2 weeks (or as necessary) to

maintain optimal performance of the air conditioner.

How to remove the air filter:

1. Hold the slot under the front panel, then uplift it outwards, and

remove the front panel.

2. Pinch the handle under the air filter and make the air filter

arched, remove it from the slot from underside to upside.

3. Clean the filter with warm, soapy water. The water should be

below 40 C to prevent distortion of the filter.

4. Rinse off and gently shake off excess water from the filter,

Allow the filter to dry before replacing it. To prevent distortion

of the filter, do not dry in direct sunlight.

To meet different requirement of different type of air conditioner,

there are two kinds of methods for your choice to treat the

condensed water.

For Cooling Only Models:

You can choose back drainage or non-drainage. See the

following procedures to perform back drainage:

1. Fit the seal onto the drain joint (which provided with your air

conditioner accessory).

2. Remove the rubber plug from the back of the unit.

3. Attach the drain joint to the back of the cabinet, where you

remove the plug and rotate 90 to securely assemble them.

4. Connect the drain joint with a extension drain hose (Locally

purchased).

Do's ( )

• Seal all air gaps in the room

• Choose the right temperature to avoid over cooling

• Ventilate the room regularly.

• Switch off the power supply if not in use for long.

• Unplug the unit while cleaning.

Don't's ( )

• Don't leave the doors and windows open when the air conditioner is on.

• Don't use hot water to clean your front grill

• Don't use scouring powder, harsh soaps, wax or polish on the grill.

• Don't switch on the air conditioner immediately after switching it off.

Wait for 2 minutes.

• Don't operate with a clogged filter

• Don't block air intake & outlet vents

• Don't change setting unnecessarily.

PRECAUTIONS TO BE TAKEN

2120

Suggested Remedy

Note: If the unit still does not work, or if any other types of symptoms are encountered,

shut off the mains (switch fuse unit) and call the service engineer.

Reset MCB

Replace fuse wire

If the input voltage to

the stabilizer is below

the acceptable range,

the AC will not operate

Press the On/Off key

on the control panel or

the remote

Remove all

obstructions to make

the airflow paths free

Change to COOL

mode

Make the selected

temperature less than

room temperature

Clean the air-filter

TROUBLE SHOOTING CHART

MCB has tripped

Fuse has burnt

Input voltage to the

stabilizer is below

acceptable range

The On/Off key is not

pressed

The airflow paths are

not free

The Units is in the fan

mode

Selected temperature is

more than room

temperature

Air-filter is not clean

Possible Causes

Unit does not start

Units does not cool

(Even after the normal

Time Delay of approx.

2/3 minutes for

compressor to start)

Symptoms

2322

Customer Name :

Address

Phone[O] [R]

Unit Model Unit Serial Number Dealer Name

Invoice Number Date of Purchase Date of Installation

MCB Rating Current (Amps.)

Cable Size Ambient Temp. ( C)

Earthing Room Temp. ( C)

Stabiliser Grill Temp. ( C)

Input Voltage Remote Operation

Customer's Response : To be filled up by the Customer

1. Installation completed within:

12hrs( ), 24 hrs( ) , 36 hrs ( ), more than 36 hrs ( )

2. How did you find the behavior of the Engineer :

Excellent ( J ), Good ( K ), Not satisfied ( L )

3. Overall rating of the service:

Excellent ( J ), Good ( K ), Not satisfied ( L )

4. Suggestion if any:

Job Number Engineer's Signature Customer's Signature

INSTALLATION & SATISFACTION

REPORT

2524

M/S. MIRC ELECTRONICS LTD, WARRANTS THIS ONIDA AIR CONDITIONER[(except the front grill,

knobs, remote unit and add-on plastic parts) TO THE ORIGINAL PURCHASER TO BE FREE FROM

DEFECTS IN MATERIALS AND WORKMANSHIP WITHIN ONE YEAR FROM THE DATE OF PURCHASE

AS PROVIDED IN THE WARRANTY REGISTERATION CARD.

WARRANTY FOR COMPRESSOR:

MIRC ELCTRONICS LTD, HEREAFTER WARRANTS TO THE PURCHASER OF THIS ONIDA AIR

CONDITIONER THAT FOR A PERIOD OF SIXTY MONTHS FROM THE DATE OF INVOICE .

WE WILL REPAIR/REPLACE THE COMPRESSOR WHICH PROVES UPON INSPECTION BY US OR ANY

OF OUR AUTHORISED SALES DEALERS TO HAVE BEEN DEFECTIVE DUE TO MANUFACTURING

DEFECT.

This warranty is subject to terms and conditions as mentioned below:

1. This warranty shall be valid only for the said period of 12 months as specified above, irrespective of

whether the said unit has been in use or not for any reason whatsoever, or the unit is moved from one

location to another. Warranty does not cover accessories external to the equipment.

2. The warranty period specified above shall include time taken for repairs, replacements, break-downs,

transit time etc. No notice of expiry period of warranty will be given by the company.

3. This warranty shall stand automatically terminated in the event of the said unit being serviced,

repaired, installed, de-installed, re-installed or otherwise attended to by any person or organization or

agency or by the said purchaser himself other than the authorized representative of the company.

4. Parts of the unit replaced or repaired under the terms of this warranty are warranted only for the

remaining period of the original warranty period.

5. For attending any service call under this warranty beyond the municipal limits of the locality in which

the authorized representative/dealer is situated (outstation locations), all to and fro travelling and

other incidental expenses as prevailing from time to time incurred in connection with the visit of the

service personnel, technicians, etc shall be borne by the said purchaser and shall be payable in

advance. Additionally, all expenses incurred by the authorized representative /dealer in collecting the

said unit or any part thereof from such outstation locations and its return to the original location shall

be borne by the said purchaser.

6. Any loss of refrigerant caused due to sabotage, improper handling or treatment , carelessness,

accident, fire, flood earthquake or any natural calamity any corrosive action on the original refrigerant

pipes, fittings, valves etc for whatever reasons, shall not be covered under this warranty.

7. In the event of any change in the location of the unit during the warranty period, this warranty shall

become null and void unless the fact of the proposed change is communicated in writing to the

authorized dealer at least seven (7) days prior to the said change. On receipt of such information the

authorized dealer or any of its counterparts shall arrange for de-installation of the said unit on

chargeable basis. However, in the event of any damage occuring to the unit or to any of its parts during

the course of its transit by the said purchaser, repair or replacement, the said unit or any part thereof

damaged shall not be covered by this warranty.

WARRANTY TERMS

AND CONDITIONS

2726

8. It shall be the absolute discretion of the company to a) effect the repairs or replacement of parts

whether at the site of installation or at any service centre, and b) have the job attended to either by the

Company's service personnel or its authorised dealer

9. This warranty is in the nature of and for the purpose of set forth herein above and in particular the

Company shall not in any event be liable for direct, indirect, incidental or consequential loss or

damages to either the said purchaser and /or his property or any other third party.

10. The AC is designed to operate at a range (230V +/- 10%). Any failure due to operation of the machine

beyond these limits will not be covered by the above warranty.

Customer shall ensure that a stabilizer is installed in those areas where voltage is not available within

the warranty range (230V +/- 10%). The stabilizer should be of any reputed manufacturer, tested and

recommended by the Company.

11. The purchaser should preserve the original invoice for necessary verification and produce, as and

when required.

12. Warranty null and void if:

i. The Air Conditioner is not purchased from the authorized dealers of the company.

ii. The Service Centre copy of warranty card is not received within 10days of date of purchase at the

nearest Authorised Service Centre.

iii. Any damage is caused by accident, mishandling, tampering with installation, or negligence in

following instructions of the user manual issued by Company.

iv. Any damage is caused by improper electrical circuit outside the unit or by any defective electrical

supply

v. At any time, during the warranty period if any part of the unit is tampered with, altered, repaired or

serviced by any unauthorized person, not being the authorized representative of the company or

its authorized dealers

vi. The serail number of the unit or any part thereof is damaged , defaced, altered, obliterated , or

tampered with or removal for any reason whatsoever

viii. The unit is unauthorisedly moved from its original place of installation or re-installation

13. None of the employees and /or Authorized Dealers of the Company have any authority whatsoever to

vary the terms and conditions of this warranty.

14. This warranty shall be deemed to have been issued at Mumbai, state of Maharashtra and courts at

Mumbai shall have exclusive jurisdiction on matters covered by or following from this warranty, and

the original purchaser alone shall have cause of action arising out of the transaction.

Preventive Maintenance Service 1 Date: ________

Customer Identification Number: ___________________________________________

Name of the customer: ____________________________________________________

Installation address: ______________________________________________________

________________________________________________________________________

Phone: _________________ Mobile: __________________ Fax: ________________

E-mail: _________________________________________________________________

Unit model: ____________________________ Serial Number: __________________

Service report number: ___________________________________________________

Customer's Signature: _______________________ Name: _______________________

Preventive Maintenance Service

Customer Identification

Number:

______________________

Unit Model: ___________

Sr. No: _______________

Name of Serviceman:

______________________

Date: ______ Time: _____

Sign. of Serviceman

Preventive Maintenance Service 2 Date: ________