Onkyo TXNR905 - AV Network Receiver Use and care manual

FIRMWARE UPDATE -1
TX-NR905
TX-NR905 Rear Panel
(Target unit)
FRONT R (BTL)
V
S
MONITOR
OUT
ZONE 2
OUT
RS232
DIGITAL
COAXIAL
OPTICAL
REMOTE
CONTROL
IN 1
IN 1
IN 2
IN IN IN IN
PHONO
FRONT R SURR R CENTER SURR L
SURR BACK R
CD TAPE AUX 1
GAME/TV
GAME/TV CBL/SAT
CBL/SAT
V1XUA CR/DVR
VCR/DVR DVD
DVD IR IN
GND
IN 2
IN 3
LL
V
S
RR
ASSIGNABLE
(DVD)
(CBL/SAT)
(VCR/DVR)
(GAME/TV)
(CD)
OUT
COMPONENT VIDEO
ASSIGNABLE
IN 3
Y
CB/PB
CR/PR
IN 2 IN 1(DVD) MONITOR
OUT
OUT IN IN OUT IN TNORFNI CENTER
REFOOWBUS
RRUS
MULTI CH
KCABRRUS
OUT
Bi-AMP
HDMI
IN 1IN 2IN 3IN 4
ASSIGNABLE
OUT
MAIN OUT SUB
ZONE2 R
ASSIGNABLE
AM
ANTENNA
SIRIUS
XM
Update Procedure
3. Make sure that the following message appears on Front Panel.
If the version is not “1.01/07615L,” DO NOT carry out upgrade with this tool.
The upgrade will cause the unit to no longer operate properly until FW is correctly reloaded.
4. Double click "Update.exe" in the folder extracted from "App_Updater_905.zip.”
If an error message like “MSCOMM32.OCX is missing" appears, a set of missing files needs to be installed.
Go to FIRMWARE UPDATE -3.
MainUpdate Mode
Ver.1.01/07615L
Preparation for Update (Main)
1. Personal computer(PC) with Windows XP or 2000
2. Cable: RS232 straight cable
3. Writing soft: "App_Updater_905.zip" Unzip this file in advance. (File name depends on the version.)
If VB6 Runtime is not installed in the PC, go to FIRMWARE UPDATE -3 first.
1. While the target unit is unplugged, connect the unit and PC with RS232 straight through cable.
2. Holding down [Enter], plug AC cord of the target unit.
Hardware and Software
RS232 terminal
RS232 straight through cable
PC
(Personal computer)

FIRMWARE UPDATE -2
TX-NR905
Update Procedure (continued)
7. Make sure that the writing starts.
9. Unplug, plug the unit again, and turn it on.
Confirm that the unit has successfully been upgraded by holding down [DISPLAY] and then pressing [STANDBY/ON].
e.g.
8. Wait until the writing completes and the unit is automatically turned off.
WARNING: Never turn off the unit during writing.
If power is accidentally turned off due to power outage etc., “MainUpdate Mode” will appear when the power is turned on
next time. Carry out the upgrade from the beginning.
6. Click "Main Update in the window.
5. Make sure that a COM port to which RS232 straight cable is connected is correctly selected.
This information will appear when
the click of [Main Update] is accepted.
The number is going up
as writing is proceeding.
Main:
9 1.05/07927A

FIRMWARE UPDATE -3
TX-NR905
Installation Procedure
3. Install the software by following instructions that will appear step by step on the window.
If “App_Updater_905.zip” has already been unzipped in “Preparation for Update” in FIRMWARE UPDATE -1,
return to Step 1 of Update Procedure.
5. Return to Step 1 of Update Procedure in FIRMWARE UPDATE -1.
4. Find “Firmware” folder which has been created in the folder where the software has been installed.
Copy “SR875” folder from “Setup_Updater905E” to under the “Firmware” folder.
Preparation for Update (Main)
1. "Setup_Updater905E.zip" Unzip this file in advance. (File name depends on the version.)
1. Exit from every running application software.
2. Double click "setup.exe" in the folder extracted from "Setup_Updater905E.zip.”
Software
Copy