Onyx LZR PRO 900W User manual

USER MANUAL
VERSION 1.0

USER MANUAL
VERSION 1.0
Please read this manual carefully before using the
product. The manual contains important instructions for
the safe use and longevity of your bike.
If you need any type of support or warranty information
for your LZR, please contact ONYX before returning
it back to where you purchased the bike. The ONYX
Support Team is ready to help you via phone or email.
You can also visit our website for more info.
Phone: [phone] (M-F 9am-5pm PST)
Email: [e-mail]
Web: onyxmotorbikes.com

LZR PRO 900W

LZR 500W

Platform Pedals Y-Wrench
Spoke Refectors F/R Reectors
Charger 15mm Wrench
Manual
ASSEMBLYPREP
To prepare for the assembly of your LZR, rst take
out all pieces of the LZR from the box and remove all
packaging. Also, open the small parts box and remove
all tools, parts, and everything else that’s inside of it.
Note that the assembly process is the same for both the
LZR PRO 900w and the LZR 500W.

Handlebars
Stem
Rear Tire
Rear Rim
Display
Seat
Seat Post
Seat Clamp
Front Tire
Frame
Suspension Fork
Mid-Drive motor
Front Brake Caliper
Front Brake Rotor
Front Rim
Pedal
Pedal Crank
Front Sprocket
Chain
Rear Brake Rotor
Rear Brake Caliper
Chain Tensioner
LZR PRO 900W

Handlebars
Stem
Rear Tire
Rear Rim
Display
Seat
Seat Post
Seat Clamp
Front Tire
Frame
Suspension Fork
Mid-Drive motor
Front Brake Caliper
Front Brake Rotor
Front Rim
Pedal
Pedal Crank
Front Sprocket
Chain
Rear Brake Rotor
Rear Brake Caliper
Chain Tensioner
LZR 500W

INSTALL THE HANDLEBAR
Remove the four screws from the stem. Use the
Y-Wrench Allen Key Tool to remove the screws on the
front of the stem.

INSTALL THE HANDLEBAR
Install the handlebar lined up properly with the tire and
frame, insert each of the four screws, and loosely thread
them in a crisscross pattern until the bar does not
move. Align and center the bars then tighten the four
screws on the stem to clamp the handlebars tight so
there is no twisting or other movement possible. Always
use a crisscross pattern when clamping the handlebar
to the stem.
centerline

INSTALL THE FRONT WHEEL
Be sure to remove the plastic front caliper brake pad
spacer and the front wheel axle before starting this step.
Align the front wheel hub to the holes on the forks. The
brake rotor should be aligned so that it ts inside the
front brake caliper where you just removed the plastic
brake pad spacer.

INSTALL THE FRONT WHEEL
Once the hub is aligned with both sides of the
through-holes on the fork, install the axle through the
fork and hub and tighten. Once the axle is tight and you
can pull on the lever away from the forks and re-adjust
the angle of the lever.

ATTACH THE PEDALS
Install the left and right pedals by screwing them into
the pedal crank arms. Pay attention to which pedal is
being installed on each side. The left pedal is reverse
threaded so it is tightened counter-clockwise. You
can tell the two pedals apart by looking for the “R” on
the right pedal and “L” on the left. After the pedals are
screwed on by hand, use the 15mm open end of the
wrench to give the pedals a nal tightening.

ADJUST THE SEAT HEIGHT
To adjust the seat height, open the seat clamp lever
and raise or lower the seatpost to where it feels
comfortable. Once in a comfortable position, close the
seat clamp lever back to its original position.