Opengear CM4132 User manual

CM4116, CM4132 & CM4148 Quick Start (520004-Rev 3.5) Page 1
CM4116, CM4132 & CM4148
Quick Start Guide
Thank you for purchasing the CM4116/32/48 console server. This Quick Start walks you
through installation, configuration and local operation. For more details please refer to
the User Manual on the CDROM.
Step1 Check kit contents
CM4116/32/48
Console server
UTP cables (2) and
DB9F-RJ45S straight
and cross-over
Quick Start &
CDROM
Power cable
(-SAC models only)
Step 2 Connect the hardware
Power the CM4116/32/48 console server. The –SAC models have a universal AC
power supply built in, that plug into the mains. The –SDC models have a DC
supply and an external screw connector block for connecting to the DC power
sources
Connect the LAN port on the console server to your network, connect your serial
devices to the console server SERIAL ports 1 through 16/32/48
Note: If you plan to use out-of-band (OoB) dial-in access, connect an external
modem to the LOCAL serial port.
Step 3 Set up the console server
The default console server IP Address is 192.168.0.1 (subnet mask 255.255.255.0 ).
With a web browser on any computer that is LAN connected to the console server:
Enter https://192.168.0.1 into the address bar

CM4116, CM4132 & CM4148 Quick Start (520004-Rev 3.5) Page 2
Note: The LAN connected computer must have an IP address in the same
network range (192.168.0.xxx) as the console server. If this is not
convenient, you can use the ARP Ping command to set the IP address
(refer User Manual or online FAQ for details). The console server also
has its DHCP client enabled by default, so it will automatically accept any
network IP address assigned by any DHCP server on your network –and
will then respond at both 192.168.0.1 and its DHCP address.
Log in using the default system user name root and the default password
default, a Welcome screen listing the basic configuration steps is displayed
Select System: Administration, enter and confirm a new System Password
and click Apply
To assign your console server a static IP address or to permanently enable
DHCP, select System: IP then Network Interface and check DHCP or Static
for Configuration Method
Step 4 Configure serial & network devices
Select Serial & Network: Serial Port to display the label, mode and protocol
options currently set for each serial port –by default, each serial port is set to
Console Server mode (refer the User Manual if other modes are required)
To configure the serial port, click Edit
Configure the Common Settings (Baud Rate, Parity, Data Bits, Stop Bits and
Flow Control) to match those of the device being controlled
Select the Console Server protocols (Telnet, SSH, TCP and RFC2217) that are
to be used for the data connection to the serial port

CM4116, CM4132 & CM4148 Quick Start (520004-Rev 3.5) Page 3
A Logging Level may also be set to specify the level of information to be
logged and monitored for the serial port
Click Apply
To enable access through the console server to a locally networked computer
(referred to as a host ), select Serial & Network: Network Hosts and click
Add Host
Enter the IP address/DNS Name of the host
Edit the Permitted Services used for accessing this host, e.g. HTTPS (TCP
port 443), VNC (TCP port 5900), or add custom TCP or UDP port numbers –only
the services specified here are tunneled through to the host, all other services
are blocked
At this stage you may also specify the level of information to be logged and
monitored for each host access
Click Apply
Step 5 Add new users
Note: It is recommended that you set up a new Administrator user (in the admin
group with full access privileges) and login as this new user for all ongoing
administration functions (rather than continuing as root )
For each new user, select Serial & Network: Users & Groups and click Add
User
Enter a Username and enter and confirm a Password,and nominate the
Accessible Hosts and Accessible Ports the user is allowed to access
To grant limited access to the Management Console, check the user Group, to
grant full access to the Management Console, check the admin Group –by
default the user is granted no Management Console access
Click Apply
Please register your product to activate the warranty and to
automatically receive advice of future firmware updates. Go to:
http://opengear.com/product-registration.html

CM4116, CM4132 & CM4148 Quick Start (520004-Rev 3.5) Page 4
Step 6 Advanced configurations
The console server offers many more advanced functions including:
The Alerts & Logging: Alerts facility monitors serial ports, hosts, user logins,
UPSes (Uninterruptible Power Supplies), RPCs (Remote Power Controllers, such as
PDUs and IPMI devices) and EMDs (Environmental Monitoring Devices). A broad
selection of trigger events (such data patterns, temperature or battery levels) can
be specified. When triggered, a warning email, SMS, Nagios or SNMP alert is sent
to a nominated destination.
Extensive management of UPSes and RPCs using open source NUT and Powerman
tools. The Manage: Power facility enables both administrators and regular users
to monitor and control attached PDU power strips, and servers with embedded
IPMI BMCs.
You can connect EMDs to any serial port (with an adapter) and remotely monitor
the temperature, humidity, physical access, smoke alarms, etc. Details are
provided in the EMD5000 Quick Start supplied with the EMD.
Historical logs of all communications with serial and network attached devices,
system activity, UPS and PDU power status, environmental status, etc. The level of
logging is set as ports and devices are configured, Alerts & Logging: Port Log
allows this history to be saved locally or remotely. Logs can be viewed from the
Status and Manage menus.
Other advanced features, such as Serial Port Cascading , remote Authentication ,
Trusted Networks , Secure Tunneling , Nagios Distributed Monitoring , the Command
Line interface –these are covered in detail in the User Manual on the CDROM.
Note: On the CDROM you will find the PortShare and SDT Connector software tools.
SDT Connector provides you with secure, point and click access to the console
server and all the attached devices
PortShare connects the COM/tty port applications on your Windows PC, Linux
server or virtual machine to the serial devices attached to the console server
Refer to the provided Quick Starts for details