OPTEX FA CD5 Series User manual

●Read this Instruction Manual
before use for the safe and correct
operation.
●Keep this Instruction Manual for
the future reference and refer to it
whenever necessary.
Table of Contents page
SAFETY PRECAUTIONS ............. 3
Meanings of Safety Symbols............................... 3
Mandatory Requirements..................................... 4
Precautions for Installation.................................. 5
Operating Precautions.......................................... 5
Cautions for Laser Product .................................. 6
6SHFL¿FDWLRQV..................................... 8
BASIC INFORMATION BEFORE USE
.... 10
Parts Identifications of Sensor Head.................. 10
Package Descriptions......................................... 10
Option ................................................................ 11
Sensor Head Installation .......... 12
Installing Direction ............................................ 12
Distance indicator .............................................. 14
Sensor head Installation.....................................15
Connecting Connectors for Sensor Head........... 16
APPENDIX........................................... 17
Sensor Head Instruction Manual
Displacement Sensor CD5 Series
Laser Type
(CD5-L_25,CD5-_30,CD5-_85,CD5-_150,CD5-W350,CD5-W500,CD5-W2000)
91, Chudoji Awata, Shimogyo-ku, Kyoto, 600-8815 Japan
Tel : [phone] Fax : [phone]
Website:http//www.optex-fa.com
Manufactured and sold by :
QCLQMPFC?B+K?LS?J+C,glbb/ /1,/0,/5282/8.4N
K
Ramco Innovations 800-280-6933 www.optex-ramco.com
For Technical/Application Support
Contact Ramco Innovations
To check availability or place an order email: [email protected]

2
▼
Displacement sensor
FOREWORD
Thank you for purchasing the Displacement Sensor CD5 Series. We hope you
DUH IXOO\ VDWLV¿HG ZLWK WKLV SURGXFW DQG HQMR\ LWV SHUIRUPDQFH7R HQVXUH \RXU
satisfaction, please follow the instructions below.
●Carefully read this instruction manual and keep it for future reference.
●If you have any question about the instructions here or a request for replacing
the lost instruction manual, contact the sales office or store where you
purchased this product.
●The contents in this instruction manual are protected by copyright and all
rights are reserved by OPTEX FA CO., LTD. The descriptions and information
included in this manual shall not be copied nor reproduced to any other form.
This products may be listed as articles to be regulated for export such as
strategic materials by the Foreign Exchange and Foreign Trade Control Act.
Therefore, if you intend to export these, be sure to follow the necessary
procedures, such as application for an export permit from the Government.
Warranty
Whereas all of our products are tested in accordance with the strict internal
standard, a faulty unit may unexpectedly be distributed. If this is the case with
\RXU SURGXFW LGHQWLI\ LWV VWDWXV DQG FRQWDFW WKH VDOHV RI¿FH RU VWRUH ZKHUH \RX
purchased it.
●The warranty period shall be one(1) year after its delivery to the customer.
●If the failure results from a manufacturer' s fault, the manufacturer will replace
the product (by sending a substitute) without charge except the following
cases :
1. Failure due to any abuse or misuse
2. Failure due to a cause other than the product
)DLOXUHGXHWRXQDSSURYHGPRGL¿FDWLRQRUUHSDLU
4. Failure due to acts of God
This warranty is limited to the delivered product only.
This warranty shall not cover the secondary damage caused by the faulty
product.
QCLQMPFC?B+K?LS?J+C,glbb0 /1,/0,/5282/8.4N
K
Ramco Innovations 800-280-6933 www.optex-ramco.com

CD5 Sensor Head
▼
3
SAFETY PRECAUTIONS
Carefully read and understand the safety precautions before operation.
They provide the important information to protect your health and property. Strictly
follow this instruction manual, and do not apply any other installing/operating
procedure which is not described in this manual.
Meanings of Safety Symbols
Indicates a possible hazard that may result in death or serious
injury if the product is used without observing the stated
instructions.
Indicates a possible hazard that may result in personal injury or
property damage if the product is used without observing the
stated instructions.
QCLQMPFC?B+K?LS?J+C,glbb1 /1,/0,/5282/8.4N
K
Ramco Innovations 800-280-6933 www.optex-ramco.com

4
▼
Displacement sensor
Mandatory Requirements
・ This product cannot be used as a safety device to protect human
body.
・
Do not stare into laser beam or point laser beam at eyes since it may
damage the eyesight.
・ Do not disassemble or modify the product since it is not designed
automatically to stop the laser emission when it is opened.
Disassembling or modifying at customer’s end may cause personal
LQMXU\¿UHRUHOHFWULFVKRFN
・
Use only the special controller and an extension cable to connect the
sensor head. Other units/ cables may cause an accident or damage
the product.
・
 8VHWKHSURGXFWIROORZLQJVSHFL¿FDWLRQVVXFKDVWKHUDWHGYDOXHDQG
environmental condition.
・
Use of controls or adjustments or performance of procedures
RWKHUWKDQWKRVHVSHFL¿HGKHUHLQPD\UHVXOWLQKD]DUGRXVUDGLDWLRQ
exposure.
・
 'RQRWDSSO\DVKRFNWRWKHJODVVFRYHURIWKHHPLWWLQJUHFHLYLQJ
SDUW,WPD\EUHDNWKHFRYHU
QCLQMPFC?B+K?LS?J+C,glbb2 /1,/0,/5282/8.5N
K
Ramco Innovations 800-280-6933 www.optex-ramco.com

CD5 Sensor Head
▼
5
Precautions for Installation
・
Do not install or use the product at the following places. It may lower
accuracy or cause a failure.
A place where;
 7KHRSHUDWLQJWHPSHUDWXUHRUKXPLGLW\H[FHHGVWKHVSHFL¿HGYDOXH
The receiving part is directly exposed to sunlight or ambient light. (Use a tool like
DVXQYLVRUIRULPSURYHGDFFXUDF\
 &RQGHQVDWLRQRFFXUVE\WHPSHUDWXUHFKDQJH
 7KHUHLVPXFKGXVWRULURQSRZGHU
Water, oil, agent or organic solvent scatters or attaches to the product.
The product receives too much vibration or shock.
・
Install the product away from noise generating devices such as high
voltage cable, power line or inverter drive motor. Noise may cause a
malfunction.
・
Do not pull or apply excess power to a cable. It may damage the
product.
Operating Precautions
・
Do not use the product just after turning on. A warm-up operation over 30
minutes is required before use.
・
The sensor performance may depend on the individual units.
・
Wipe off dirt on the cover (glass) of the emitting/receiving parts using a soft
cloth etc., at every operation since it may cause incorrect detection.
QCLQMPFC?B+K?LS?J+C,glbb3 /1,/0,/5282/8.5N
K
Ramco Innovations 800-280-6933 www.optex-ramco.com

6
▼
Displacement sensor
Cautions for Laser Product
This sensor emits visible laser beam compliant with JIS C6802/IEC/FDA, laser
safety standard Class 1, 2 ( Ⅱ) or 3R ( Ⅲa).
The warning and description labels are stuck on the side of the product.
Laser type of this product
Type Red Laser Diode
Wavelength 650 nm / 658 nm
Output ȝ:P:P:
This sensor is subject to the FDA laser standard when exported to U.S.A. The
report of this sensor has been submitted to Center for Devices and Radiological
Health (CDRH).
QCLQMPFC?B+K?LS?J+C,glbb4 /1,/0,/5282/8.6N
K
Ramco Innovations 800-280-6933 www.optex-ramco.com

CD5 Sensor Head
▼
7
Label of each model
・CD5-30 / CD5-W30
・CD5-85 / CD5-W85
・CD5-150 / CD5-W150
・CD5-W350
・CD5-W500
・CD5-W2000
・CD5-L25 / CD5-LW25
This laser product cmplies with
21 CFR 1040.10
OPTEX FA CO.,LTD.
93 Chudoji Awata-cho Shimogyo-ku
Kyoto 600-8815 Japan
Place of manufacture :
OFROM CO.,LTD.
This laser product cmplies with
21 CFR 1040.10
OPTEX FA CO.,LTD.
93 Chudoji Awata-cho Shimogyo-ku
Kyoto 600-8815 Japan
Place of manufacture :
OFROM CO.,LTD.
CD5-30,CD5-85,CD5-150
CD5-W30,CD5-W85,CD5-W150,CD5-W350,CD5-W500
CD5-W2000
QCLQMPFC?B+K?LS?J+C,glbb5 /1,/0,/5282/8//N
K
Ramco Innovations 800-280-6933 www.optex-ramco.com

8
▼
Displacement sensor
6SHFL¿FDWLRQV
Model No. CD5-L25 CD5-LW25 CD5-30 CD5-W30 CD5-85
C
Optical method 6SHFXODUUHÀHFWLRQ
Center 25mm 30mm 85mm
Measuring range ±1mm ±5mm ±20mm
Light source
Red Laser Diode
Wavelength 650nm /
0D[LPXPRXWSXWȝ:
Wavelength 650nm /
Maximum output 1mW
Wavelength 658nm /
Maximum output 1mW
Wavelength 650nm /
Maximum output 1mW
Wav
e
Maxi
m
Laser
Class
IEC/JIS CLASS 1
FDA Class Ⅱ
6SRWVL]H
*1 $SS[[ȝP $SS[[ȝP $SS[[ȝP $SS[[ȝP $SS[[ȝP $SS
[
Light receiving
element Linear image sensor
Linearity ±0.08% F.S. ±0.08% F.S. ±0.08% F.S.
Resolution
*2 ȝP ȝP ȝP
Sampling period *3 ȝV6HWX
Temperature drift *4 ±0.01% F.S. / ℃±0.05% F.S. / ℃
Supply voltage Supplied from special controller
Indicator
Laser emission indicator : Green (ON during laser emission)
Distance indicator : Orange (Lights around center)
Distance indicator : Red (Lights at the near side)
Distance indicator : Green (Lights at the far side)
Distance indicator : Alternative Red/ Green(Lights alternatively outside the ran
g
Protection
category
IP67 (Including connecting part)
Operating
temperature -10 to +50℃(Free from condensation or icing) / For storage : -20 to +60℃
Operating humidity 35% to 85%RH / For storage : 35% to 85%RH
Ambient light Max. 3,000lx (Surface illuminance, Incandescent lamp)
Vibration
resistance
10 to 55Hz Double amplitude 1.5mm 2 h per XYZ axes
Material Sensor Head housing : Diecast Aluminum Cover of Emitting/receiving part : Glass
Cable extension Up to 50 m using an optional extension cable (unbundled)
Weight Appx. 250 g (Including cable)
<Measurement condition>
Unless otherwise designated, measurement condition is as follows. Using special controller/ operating te
GHSHQGLQJRQPRGHOVWLPHVLQDYHUDJHFHQWHUVWDQGDUGWHVWLQJREMHFWVSHFXODUUHÀHFWLRQHYDSR
U
'H¿QHGZLWKFHQWHUVWUHQJWKH2DWWKHFHQWHU7KHUHPD\EHOHDNOLJKWRWKHUWKDQWKHVSHFL¿HGVSRWVL
]
*2 : 4096 times in average. Other conditions are same as the above condition.
*3 : Default setting of sampling period is as follows.
&'ƑƑ 〜ƑȝV
CD5-W350 〜:ȝV
*4 : The typical value in the above condition.
QCLQMPFC?B+K?LS?J+C,glbb6 /1,/0,/5282/8//N
K
Ramco Innovations 800-280-6933 www.optex-ramco.com
Contact Ramco for Technical Support

CD5 Sensor Head
▼
9
CD5-W85 CD5-150 CD5-W150 CD5-W350 CD5-W500 CD5-W2000
'LIIXVHUHÀHFWLRQ
5mm 150mm 350mm 500mm 2,000mm
2
0mm ±40mm ±100mm ±200mm ±500mm
/
W
Wavelength 658nm /
Maximum output 1mW
Wavelength 650nm /
Maximum output 1mW
Wavelength 658nm / Maximum output 1mW
Wavelength 658nm /
Maximum output 5mW
CLASS 2 CLASS 3R
Class Ⅲa
$SS[[ȝP $SS[ijȝP $SS[[ȝP $SS[[ȝP $SS[[ȝP $SS[[ȝP
±0.05% F.S. ±0.08% F.S. ±0.08% F.S. ±0.1% F.S.

ȝP ȝP ȝP ȝP ȝP
V6HWXSWREHGRQHWKURXJKWKHFRQWUROOHU&'$VHULHV
±0.01% F.S. / ℃±0.05% F.S. / ℃
t
he range)
Appx. 450g
(Including cable)
a
ting temperature, 23 ℃RUGLQDU\WHPSHUDWXUHVXSSO\YROWDJH9'&VDPSOLQJSHULRGȝVRUȝV
H
YDSRUDWHGDOXPLQXPPLUURUGLIIXVHUHÀHFWLRQZKLWHFHUDPLFGLJLWDOPHDVXUHGYDOXH
V
SRWVL]H7KHVHQVRUPD\EHDIIHFWHGZKHQWKHUHLVDKLJKO\UHÀHFWLYHREMHFWFORVHWRWKHGHWHFWLRQDUHD
QCLQMPFC?B+K?LS?J+C,glbb7 /1,/0,/5282/8/0N
K
Ramco Innovations 800-280-6933 www.optex-ramco.com

10
▼
Displacement sensor
BASIC INFORMATION BEFORE USE
3DUWV,GHQWL¿FDWLRQVRI6HQVRU+HDG
φ
3DFNDJH'HVFULSWLRQV
●Sensor Head Main Unit
●Screw(3 pcs.)
●Instruction Manual (This document)
●Laser Label to stick on the device
QCLQMPFC?B+K?LS?J+C,glbb/. /1,/0,/5282/8/0N
K
Ramco Innovations 800-280-6933 www.optex-ramco.com