Optical Systems Design OSD2054P Series User manual

OPERATOR MANUAL
OSD2054P SERIES
10/100Base-T to 100Base-X
3-PORT SWITCH with PoE SOURCE

OPTICAL SYSTEMS DESIGN
DOC ID: 10116001
OSD2054P OPERATOR MANUAL
PAGE 3
INDEX 1
1 TECHNICAL SUMMARY........................................................................................................ 4
1.1 BRIEF DESCRIPTION ............................................................................................................ 4
1.1.1 OVERVIEW......................................................................................................................... 4
1.1.2 APPLICATIONS.................................................................................................................. 4
1.1.3 FEATURES AND BENEFITS............................................................................................. 4
1.2 TYPICAL CONFIGURATION................................................................................................ 5
1.3 TECHNICAL SPECIFICATIONS ........................................................................................... 6
1.4 OSD2054P FRONT AND REAR PANELS.............................................................................. 7
2 INSTALLATION AND OPERATION..................................................................................... 8
2.1 INTRODUCTION .................................................................................................................... 8
2.2 INSTALLATION ..................................................................................................................... 8
2.2.1 WARNING AND PRECAUTIONS..................................................................................... 8
2.2.2 OSD2054P DRAWINGS AND DIMENSIONS .................................................................. 9
2.2.3 POWER SUPPLY CONNECTIONS ................................................................................. 10
2.2.4 FIXED RJ45 COPPER PORT PIN ASSIGNMENTS........................................................ 10
2.2.5 LED INDICATORS ........................................................................................................... 11
2.2.6 FITTING SFP CONNECTORS.......................................................................................... 12
2.2.7 BASIC CONNECTIONS ................................................................................................... 12
3 MAINTENANCE...................................................................................................................... 13
3.1 INTRODUCTION .................................................................................................................. 13
3.2 EXTERNAL INSPECTION ................................................................................................... 13
3.3 ROUTINE MAINTENANCE................................................................................................. 13
4 WARRANTY ............................................................................................................................ 14
4.1 WARRANTY PERIOD.......................................................................................................... 14
4.2 REPAIRS................................................................................................................................ 14
4.2.1 WARRANTY REPAIRS.................................................................................................... 14
4.2.2 OUT-OF-WARRANTY REPAIRS.................................................................................... 14
4.2.3 SITE REPAIRS .................................................................................................................. 14
4.2.4 EXCLUSIONS ................................................................................................................... 14
FIGURE 1: OSD2054P TYPICAL CONFIGURATIONS....................................................................... 5
FIGURE 2: OSD2054P CONNECTORS................................................................................................. 7
FIGURE 3: OSD2054P DIMENSIONS................................................................................................... 9
FIGURE 4: OSD2054P MOUNTING DIMENSIONS ............................................................................ 9
FIGURE 5: MODULE POWER SUPPLY CONNECTIONS................................................................ 10
FIGURE 6: FIXED RJ45 ETHERNET CONNECTORS....................................................................... 10
FIGURE 7: LED INDICATORS............................................................................................................ 11
FIGURE 8: FITTING/REMOVING SFP CONNECTORS ................................................................... 12
FIGURE 9: BASIC CONNECTIONS.................................................................................................... 12
TABLE 1: TECHNICAL SPECIFICATIONS ......................................................................................... 6
TABLE 2: POWER CONNECTION ..................................................................................................... 10
TABLE 3: LED FUNCTION ................................................................................................................. 11

OPTICAL SYSTEMS DESIGN
DOC ID: 10116001
OSD2054P OPERATOR MANUAL
PAGE 4
1TECHNICAL SUMMARY
1.1 BRIEF DESCRIPTION
1.1.1 OVERVIEW
The OSD2054P is designed to convert between 10/100Base-T copper cabling and 100Base-X fiber
cabling. It has two RJ45 copper ports one of which supports PoE and one SFP port which can be
specified by the user for one or two fiber configuration.
The unit will operate on either singlemode or multimode fiber. Operation over at least 2km of
multimode fiber or up to 160km of singlemode fiber is possible by use of the appropriate optical
device.
A major benefit of the OSD2054P is its reliable operation over the -20°C to +75°C temperature range
which allows it to be used in environments such as roadside cabinets, mine sites and factories.
The OSD2054P module is intended for isolated use and requires an external power source.
1.1.2 APPLICATIONS
▲ Any network utilising a mix of copper
and fiber
▲ Extremely space constrained
environments
▲ Industrial IP communications
▲ Networks using Power over Ethernet
devices such as cameras, intercoms,
access control, telephones, etc
1.1.3 FEATURES AND BENEFITS
▲ Two 10/100Base-T RJ45 ports and
one SFP fiber port
▲ Supports IEEE802af Alternative B
cable wiring on one RJ45 port
▲ Complies with IEEE 802.3af standard
including compliant powered device
(PD) signature detection and
classification
▲ Provides up to 15.4W from port 1
only
▲ Supports network traffic of 10 or
100Mbps
▲ Auto MDI/MDIX
▲ Automatic TP setup: no need for
crossover cables
▲ Auto-sensing of half or full duplex
operation.
▲ Automatic setup for 10 or 100Mbps
on copper side
▲ Available for singlemode, multimode
operation over a variety of link budgets
▲ Available for operation over 1 or 2 fibers
▲ Powered by non-critical 10 to 36VDC
supply, 48VDC supply optional
▲ Operates over the temperature range of
-20 to +75°C
▲ A very compact design that fits in the
camera housing
▲ Utilizes 100Base-X SFP transceivers
that can be selected according to
specific length or fiber requirements
without changing the whole unit.
▲ DIN rail mounting
▲ SFP sold separately

OPTICAL SYSTEMS DESIGN
DOC ID: 10116001
OSD2054P OPERATOR MANUAL
PAGE 5
1.2 TYPICAL CONFIGURATION
Figure 1 below indicates the typical set-up for an OSD2054P system.
PoE
FIGURE 1: OSD2054P TYPICAL CONFIGURATIONS

OPTICAL SYSTEMS DESIGN
DOC ID: 10116001
OSD2054P OPERATOR MANUAL
PAGE 6
1.3 TECHNICAL SPECIFICATIONS
TABLE 1: TECHNICAL SPECIFICATIONS
SPECIFICATION PERFORMANCE
Electrical Data Interface IEEE802.3 Ethernet
Electrical Data Rate 10/100Mbps
Operating Mode Half or Full Duplex
Data Connector RJ45, the PoE unit mounted on the front panel and the non-PoE unit on the rear
panel
PoE IEEE802.3af
Operating Modes Alternative B (pins 4/5 and 7/8)
Optical Interface 100Base-Fx/Sx
Optical Port Connector SFP (LC connectors for 2-fiber operation and SC for 1-fiber operation)
SFP Options Short haul, long haul, single fiber operation, etc
Please consult OSD datasheet #1021000XX or contact OSD
Transmit Optical Power -15 to -8dBm into singlemode fiber (See SFP datasheet for details)
Receiver Sensitivity <-33dBm
Receiver Saturation >-3dBm
Standard Optical Link Budget
>18: >10km on multimode fiber @1310nm
> 40km on singlemode fiber @ 1310nm
> 160km possible on singlemode fiber with optional SFP
Operating Temperature -20°C to +75°C
Relative Humidity 0 to 95% non-condensing
Power Requirements +10V
DC
to +36V
DC
@ 3W plus an extra 20VA for PoE operation (Attached
powered device dependent). Use of isolated power supply is recommended
Power Connector 3.5mm 2-Way Terminal Block on the module
Dimensions (mm) 90W x 58D x 49H
Weight (kg) 0.4
1022054P05

OPTICAL SYSTEMS DESIGN
DOC ID: 10116001
OSD2054P OPERATOR MANUAL
PAGE 7
1.4 OSD2054P FRONT AND REAR PANELS
There are two fixed 10/100Mbps RJ45 copper ports: the PoE located on the front panel and non-PoE on
the rear panel. The SFP port and 2-way term-block power connector are also located on the front panel.
The SFP device is sold separately giving the user choice to use either one or two fiber communications
with various optical power outputs depending on the distance and link budget required.
OSD2054P Front Panel
OSD2054P Rear Panel
FIGURE 2: OSD2054P CONNECTORS
Fixed RJ45 PoE
Copper Port
SFP Port
Power Input
Fixed RJ45 Copper Port

OPTICAL SYSTEMS DESIGN
DOC ID: 10116001
OSD2054P OPERATOR MANUAL
PAGE 8
2INSTALLATION AND OPERATION
2.1 INTRODUCTION
This section outlines the methods required to install and operate the OSD2054P successfully. It should
be studied carefully if damage to the equipment or poor results are to be avoided.
This equipment has been fully tested prior to dispatch and is ready for immediate operation. However it
is advisable to check for external transportation damage before operation. If damage is evident, return
the unit with the packaging to your supplier immediately.
2.2 INSTALLATION
2.2.1 WARNING AND PRECAUTIONS
▲ ELECTROMAGNETIC COMPATIBILITY
WARNING: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
▲ OPTICAL OUTPUT OPERATION
WARNING: Laser Safety: Class 1 Laser Product per IEC 60825-1:2014 standard.
Class 1
The OSD2054P is a Class 1 laser product.
PRECAUTIONS
▲ All service personnel should be provided training as to the hazards of direct viewing of laser
radiation and of the precautionary measures during servicing of equipment
▲ Areas where laser products are installed should be restricted in access to trained service
personnel only and appropriate warning signs posted in the work area.
▲ All laser apertures should be covered by protective covers when not connected to optical
fibers. Never leave outputs uncovered.
▲ Laser equipment should be positioned above or below eye level where possible. Apertures
should be positioned away from personnel.
▲ Protective eyewear should be worn in the vicinity of laser equipment.

OPTICAL SYSTEMS DESIGN
DOC ID: 10116001
OSD2054P OPERATOR MANUAL
PAGE 9
2.2.2 OSD2054P DRAWINGS AND DIMENSIONS
The standard OSD2054P is designed to be mounted on an even surface and to be secured by means of
M4 or smaller screws. All dimensions are in mm. The unit also can be mounted on a standard DIN rail
with the OSD2054P DIN Rail bracket.
FIGURE 3: OSD2054P DIMENSIONS
FIGURE 4: OSD2054P MOUNTING DIMENSIONS
27.5
79.1
20.2
4.2
Ø8.5
89.6
58.0
49.0

OPTICAL SYSTEMS DESIGN
DOC ID: 10116001
OSD2054P OPERATOR MANUAL
PAGE 10
2.2.3 POWER SUPPLY CONNECTIONS
The OSD2054P requires external DC power. The voltage range of the OSD2054P is +10V
DC
to
+36V
DC
and for the OSD2054P/48V
DC
is +47V
DC
to +57V
DC
. Power should be connected to the 2-way
terminal block located on the front panel as indicated in Table 2.
TABLE 2: POWER CONNECTION
External Power Pin OSD2054P OSD2054P/48VDC
+ +10V
DC
to +36V
DC
+47V
DC
to +57V
DC
-
0V 0V
FIGURE 5: MODULE POWER SUPPLY CONNECTIONS
2.2.4 FIXED RJ45 COPPER PORT PIN ASSIGNMENTS
There are two RJ45 Ethernet copper ports on the OSD2054P; PoE is available on one port (Front
Panel). Both ports support IEEE802.3af Ethernet. Figure 6 shows the pin configuration for the fixed
RJ45 copper ports.
FIGURE 6: FIXED RJ45 ETHERNET CONNECTORS
- +
Pin
10Base
-
T
10
0Base
-
T
PoE
1 TX+ TX+ TX+
2 TX- TX- TX-
3 RX+ RX+ RX+
4 n/c n/c VDC+
5 n/c n/c VDC+
6 RX- RX- RX-
7 n/c n/c VDC-
8 n/c n/c VDC-
Tx: Transmit
Rx: Receive
n/c: Not Connected
Fixed PoE Port
Front Panel
Fixed Copper Port
Rear Panel
LNK/ACT SPD
1 2 3 4 5 6 7 8
LNK/ACT SPD
1 2 3 4 5 6 7 8

OPTICAL SYSTEMS DESIGN
DOC ID: 10116001
OSD2054P OPERATOR MANUAL
PAGE 11
2.2.5 LED INDICATORS
Front Panel Rear Panel
FIGURE 7: LED INDICATORS
TABLE 3: LED FUNCTION
No FUNCTION
Indicator On LED Colour Off Blinking
PoE PoE Active Green No PoE -
SPD Copper Speed:
10/100Mbps Green N/A -
PWR Power On Green Power Off -
LNK/ACT Copper Link Activity Yellow No Copper Link Activity
(1)
LNK SPD Fiber Link Speed Green No Optical Link Activity
(1)
Note: (1) Activity indicates traffic for both copper and fiber port.






OPTICAL SYSTEMS DESIGN
DOC ID: 10116001
OSD2054P OPERATOR MANUAL
PAGE 12
2.2.6 FITTING SFP CONNECTORS
Care should be taken when inserting/removing the SFP connectors from the SFP port as SFP modules
are Electrostatic (ES) sensitive and Electrostatic Discharge (ESD) precautions should be taken when
installing. Ensure that the SFP is fully engaged and latched into position.
Inserting SFP – Ensure that the SFP lever is in the locked position and insert into appropriate SFP
port. Gently push the SFP until it locks into place. Remove plastic/rubber dust cap and fit appropriate
fiber cable.
Removing SFP – Remove fiber connector. Pull the SFP lever down to unlock SFP from housing.
Using the lever, gently pull the SFP out.
Fiber SFP
FIGURE 8: FITTING/REMOVING SFP CONNECTORS
2.2.7 BASIC CONNECTIONS
Figure 9 shows basic user connections to the OSD2054P.
FIGURE 9: BASIC CONNECTIONS
Inserting
SFP
Removing
SFP
1
2
Ethernet cable
with PoE
LC Fiber cable
Power
Chassis Ground
Ethernet cable

OPTICAL SYSTEMS DESIGN
DOC ID: 10116001
OSD2054P OPERATOR MANUAL
PAGE 13
3MAINTENANCE
3.1 INTRODUCTION
The following section outlines the fault-finding procedure for the OSD2054P modems. Please take note
of the following:
▲ Personnel without appropriate training should not attempt any maintenance except that outlined
below.
▲ If further maintenance is attempted you are warned that every care should be taken to ensure that
internal measurements made while the equipment is operational are taken carefully as some
components within the unit are expensive and may be damaged by failure of any portion of their
support circuitry.
▲ Some components within the unit are Electrostatic (ES) sensitive and Electrostatic Discharge
(ESD) precautions should be taken when performing maintenance upon the unit.
3.2 EXTERNAL INSPECTION
Visually check for the following:
▲ Check that the correct power source is connected to the power socket.
▲ Check that the Ethernet cables are connected to the modem correctly.
▲ Inspect the SFP optical connectors for any contamination and clean using isopropyl alcohol and a
lint free tissue if any contamination is detected.
3.3 ROUTINE MAINTENANCE
▲ There is no routine maintenance required with the OSD2054P.

OPTICAL SYSTEMS DESIGN
DOC ID: 10116001
OSD2054P OPERATOR MANUAL
PAGE 14
4WARRANTY
Thank you for purchasing equipment designed, manufactured and serviced by Optical Systems Design
(OSD). OSD warrants that at the time of shipment, its products are free from defects in material and
workmanship and conforms to specifications. Our Warranty conditions are outlined below:
4.1 WARRANTY PERIOD
For warranty period, please call your local OSD distributor.
4.2 REPAIRS
Optical Systems Design reserves the right to repair or replace faulty modules/units. Please obtain a
“Return Material Authorisation” (RMA) form and number before returning goods.
Goods must be returned in adequate packing material to Optical Systems Design, Warriewood, NSW,
Australia or its nominated authorised representative, for all repairs.
4.2.1 WARRANTY REPAIRS
Return shipments to OSD shall be at customer's expense and freight back to the customer will be at
OSD expense.
4.2.2 OUT-OF-WARRANTY REPAIRS
OSD reserves the right to repair or replace any faulty goods. Freight costs and insurance for both
journeys are met by the user. All equipment repaired by OSD will have a 3-Month Warranty from the
date of dispatch.
4.2.3 SITE REPAIRS
By agreement site repairs may be undertaken for which out of pocket, hotel and travel expenses will be
charged.
4.2.4 EXCLUSIONS
This warranty does not apply to defects caused by unauthorized modifications, misuse, abuse or
transport damage to the equipment. All modifications to OSD’s standard product will need written
authorization and will be charged at normal repair rates. All modifications are to be carried out by OSD
Technicians. Warranty is void if unauthorized removal and/or tampering with serial number and/or
repair labels is evident.

OPTICAL SYSTEMS DESIGN
DOC ID: 10116001
OSD2054P OPERATOR MANUAL
PAGE 15

Optical Systems Design Pty. Ltd.
7/1 Vuko Pl. Warriewood 2102
P.O. Box 891 Mona Vale
N.S.W. Australia 2103
Telephone: [phone]
Facsimile: [phone]
Email: [e-mail]
Web Site: www.osd.com.au
OPTIC L
SYSTEMS
DESIGN
PTY LTD A.B.N. 83 003 020 504
Printed in Australia