Optical Systems Design OSD2790SFP User manual

Quick Start Guide
OSD2790SFP
MANAGED 24 x 100M/1G SFP
+ 4 x 1G TRUNK/UPLINK SFP ETHERNET
SWITCH

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 3
INDEX 1
1 INTRODUCTION ...................................................................................................................... 4
2 TECHNICAL SUMMARY........................................................................................................ 4
2.1 BRIEF DESCRIPTION ............................................................................................................ 4
2.1.1 OVERVIEW......................................................................................................................... 4
2.1.2 APPLICATIONS.................................................................................................................. 4
2.1.3 FEATURES AND BENEFITS............................................................................................. 5
2.2 TECHNICAL SPECIFICATIONS ........................................................................................... 6
3 INSTALLATION........................................................................................................................ 7
4 OSD2790SFP FRONT AND REAR PANELS ......................................................................... 8
4.1 FRONT PANEL ....................................................................................................................... 8
4.2 REAR P ANEL ............................................................................................................................ 8
5 POWER SUPPLY CONNECTIONS ........................................................................................ 9
6 LED INDICATORS ................................................................................................................... 9
7 FITTING SFP CONNECTORS .............................................................................................. 10
8 CLI OVERVIEW ..................................................................................................................... 11
8.1 C ONNECT TO CLI .................................................................................................................... 11
8.2 CLI COMMAND FOR IP C ONFIGURATION ................................................................................. 12
9 GUI OVERVIEW ..................................................................................................................... 13
9.1 D EFAULT S ETTING ................................................................................................................... 13
9.2 L OG INTO THE S WITCH ............................................................................................................ 13
9.3 GUI O VERVIEW ....................................................................................................................... 13
9.4 IP C ONFIGURATION ................................................................................................................. 14
9.5 U SERS A UTHENTICATION ........................................................................................................ 15
9.6 S AVE C ONFIGURATION TO S TART - UP ...................................................................................... 16
9.7 P ORT S PEED S ETTING .............................................................................................................. 16
10 WARRANTY ............................................................................................................................ 17
10.1 WARRANTY PERIOD.......................................................................................................... 17
10.2 REPAIRS................................................................................................................................ 17
10.2.1 WARRANTY REPAIRS.................................................................................................... 17
10.2.2 OUT-OF-WARRANTY REPAIRS.................................................................................... 17
10.2.3 SITE REPAIRS .................................................................................................................. 17
10.2.4 EXCLUSIONS ................................................................................................................... 17
FIGURE 1: FRONT PANEL.................................................................................................................... 8
FIGURE 2: REAR PANEL ...................................................................................................................... 8
FIGURE 3: POWER CONNECTION...................................................................................................... 9
FIGURE 4: FITTING/REMOVING SFP CONNECTORS ................................................................... 10
TABLE 1: TECHNICAL SPECIFICATIONS ......................................................................................... 6
TABLE 2: LED FUNCTION ................................................................................................................... 9

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 4
1INTRODUCTION
Thank you for choosing the OSD2790SFP 28-Port Gigabit Managed Ethernet Switch. This Quick Start
Guide is designed to guide you through the installation and basic software function.
2TECHNICAL SUMMARY
2.1 BRIEF DESCRIPTION
2.1.1 OVERVIEW
The OSD2790SFP is a managed 24 port 100M/1G SFP + 4 port 1G Trunk/Uplink SFP Ethernet
Switch. A number of various SFPs can be used including 100Mbps, 1Gbps duplex, single-fiber and
RJ45 Copper. Please see OSD SFP datasheets for options available.
2.1.2 APPLICATIONS
▲ Managed L2/3 switch for small to
medium-sized enterprise networks
requiring very high throughput.
▲ Redundant and self-healing network
▲ Ideal for star configured optical
networks
▲ Industrial IP communications for
rugged environments
▲ Available with either DC or AC
powering. The DC version has dual
redundant inputs as standard whereas
redundant AC powering is optional
for the AC version
.

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 5
2.1.3 FEATURES AND BENEFITS
General
•L2/3 managed 1G Ethernet switch
•Supports RSTP/MRSTP/STP for
Ethernet redundancy
•CPU Memory 128MB
•User-friendly web browser based GUI
•CLI and SNMP management
Port Control
•Port speed and flow control
•Port status -- link monitoring
•Port statistics -- MIB counters
Qos
•Traffic classes (1, 2, or 4, 8 active
priorities)
•Port default priority and user assigned
priority
•Scheduler priority
•QoS control
•Storm control
L2 Switching
•IEEE 802.1D Bridge with auto MAC
learning/aging
•IEEE 802.1Q static VLAN
•Private VLAN (static)
•80Gbps switching backplane
•IEEE 802.1Q-2005
– Rapid spanning
tree (RSTP)
•IEEE 802.3ad Link aggregation, static
and LACP
•DHCP client
•Port mirroring
Security
•Port-based 802.1X
•Web and CLI authentication and
authorization
OAM
•IEEE 802.3ah Link OAM
Multicasting
•IGMP Snooping (IGMPv2, IGMPv3)
•Multicast Listener Discovery (MLD)
v1 and v2
Power Saving
•Ethernet Energy Efficiency
oLink down power savings
oScales power based on cable
length
•Thermal protection
Management
•HTTP server
•Web management
•CLI console port
•Management access filtering
•System log
•Software download through web
•SNMPv1/v2c/v3Agent
•IEEE 802.1AB-2005 Link Layer
Discovery, LLDP
•Configuration download or upload
•RFC 1213 MIB II
•RFC 3621 LLDP-MED power
•RFC 3635 Ethernet-like MIB
•RFC 4188 Bridge MIB
•Private MIB framework
•IEEE 802.1 MSTP MIB
•IEEE 802.1AB LLDP

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 6
2.2 TECHNICAL SPECIFICATIONS
TABLE 1: TECHNICAL SPECIFICATIONS
SPECIFICATION PERFORMANCE
Electrical Data Interface IEEE802.3z 1000Base-Lx, 1000Base-Sx
IEEE802.3u 100Base-Fx
Operating Mode
Full duplex for 100M/1G
Store-and-Forward
IEEE802.3x full-duplex flow control
Number of Optical Port
Connectors SFP x 28: 24 for 10/1000SFPs Port1-24, 4 for the 1G uplink/trunk ports
Optical Port Connector Type SFP (LC or SC)
SFP Options
Short haul, long haul, single fiber operation, etc.
Please see OSD Datasheets #102100XX and #1021000XX for 100Mbps and
1Gbps SFP optical modules
Indicators
28 x 100M/1G Link/Activity/Speed
2 x Power
1 x Status
Configuration Connector Mini USB Console Port
Alarms Four: Two for Power Supply Status
Two user definable via the GUI as specified in the user manual
Alarm Interface Four opto-isolated relay drivers via two 4-way 3.5mm terminal blocks
Control System Reset
Operating Temperature -20°C to +75°C for OSD2790SFPDC
-20°C to +65°C for OSD2790SFPAC and OSD2790SFPDAC
Relative Humidity 0 to 95% non-condensing
Power Requirements
+10 to +36V
DC
@ 40VA Max for DC version
90 to 264V
AC
@ 50VA Max for standard single AC version
90 to 264V
AC
@ 55VA Max for optional redundant AC version
Power Connector
4 way 5.08mm Terminal Block for DC powered version
One IEC power inlet module for the standard AC powered version
Two IEC power inlet modules for the optional redundant AC powered version
Dimensions of Enclosure (mm) 443W x 300D x 44H
1022790SFP01

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 7
3INSTALLATION
ELECTROMAGNETIC COMPATIBILITY
WARNING: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
OPTICAL OUTPUT OPERATION
WARNING: Laser Safety: Class 1 Laser Product (SFP) per IEC 60825-1:2014 standard.
Class 1
The OSD2790SFP is a Class 1 laser product when SFPs
are fitted
PRECAUTIONS
▲ All service personnel should be provided training as to the hazards of direct viewing of laser
radiation and of the precautionary measures during servicing of equipment
▲ Areas where laser products are installed should be restricted in access to trained service
personnel only and appropriate warning signs posted in the work area.
▲ All laser apertures should be covered by protective covers when not connected to optical
fibers. Never leave outputs uncovered.
▲ Laser equipment should be positioned above or below eye level where possible. Apertures
should be positioned away from personnel.
▲ Protective eyewear should be worn in the vicinity of laser equipment.

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 8
4OSD2790SFP FRONT AND REAR PANELS
4.1 FRONT PANEL
FIGURE 1: FRONT PANEL
1. PSU1 Status LED
2. PSU2 Status LED
3. Status LED
4. USB Console Port
5. 24 x 100/1000M SFP ports with 100M/1G Link/Activity/Speed LEDs
6. 4 x 1G Trunk/Uplink SFP ports with 100M/1G Link/Activity/Speed LEDs
4.2 REAR PANEL
FIGURE 2: REAR PANEL
7. PSU 2 Redundant Power Supply Input
8. PSU Alarm Output connector
9. Programmable Alarm Output Connector
10. Reset Switch
11. Earth/Ground screw
12. PSU 1 Redundant Power Supply Input
1
2
3
4 5 6
7 8 9 10 11 12

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 9
5Power Supply Connections
Connect the two IEC Power connectors to PSU 1 and PSU 2 located on the rear of the unit.
The OSD2790SFP requires external 90 to 264V
AC
@ 55VA Max power.
FIGURE 3: POWER CONNECTION
6LED Indicators
TABLE 2: LED FUNCTION
LED
Function
PSU 1
• Red – PSU 1 Not connected or faulty
•
Green – PSU 1 On
PSU 2
• Red – PSU 2 Not connected or faulty
•
Green – PSU 2 On
Status
• Red – Standby/Initialization Mode
•
Green – Normal status
SFP 1-24
Port Status LED will indicate
the below
information.
• Green – 1Gbps
• Amber – 100MBps
•
Off – No Connection
SFP 25-28
Port Status LED will indicate
the below
information.
• Green – 1Gbps
• Off – No Connection

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 10
7Fitting SFP Connectors
Care should be taken when inserting/removing the SFP connectors from the SFP port as SFP modules
are Electrostatic (ES) sensitive and Electrostatic Discharge (ESD) precautions should be taken when
installing. Ensure that the SFP is fully engaged and latched into position.
Inserting SFP – Ensure that the SFP lever is in the locked position and insert into appropriate SFP
port. Gently push the SFP until it locks into place. Remove plastic/rubber dust cap and fit appropriate
fiber cable.
Removing SFP – Remove fiber connector. Pull the SFP lever down to unlock SFP from housing.
Using the lever, gently pull the SFP out.
Fiber SFP
FIGURE 4: FITTING/REMOVING SFP CONNECTORS
Inserting
SFP
Removing
SFP
1
2

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 11
8CLI OVERVIEW
8.1 CONNECT TO CLI
The Silicon Laboratories CP210x VCP Drivers is required to be installed on the PC before connecting
the switch.

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 12
1. Connect the Console Port on OSD2790 (Mini USB) to PC with USB cable.
2. Using HyperTerminal to set up the following parameters.
•Baud Rate: 115200
•Data Bits: 8
•Parity: None
•Stop Bits: 1
•Flow Control: None
3. Check the link by pressing <ENTER>. The line should jump to the next line.
4. Using the Username and password to login the switch
•Default Username: admin
•Default Password: (None)
8.2 CLI COMMAND FOR IP CONFIGURATION
•show ip interface brief:Display the current IP address and subnet mask.
•configure terminal -> interface vlan 1 -> ip address <IP address> <subnet mask>: Setup the
switch IP address.
•copy running-config startup- config: Save the current configuration to start-up configuration.
PS: All configuration changes must be saved otherwise all the changes will be lost after
rebooting!

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 13
9GUI Overview
9.1 DEFAULT SETTING
• IP Address: 192.168.0.99
• Subnet Mask: 255.255.255.0
• Gateway: 192.168.0.1
• User Name: admin
• Password: (None)
9.2 LOG INTO THE SWITCH
• Connect a switch port to a PC, Change the PC’s network IP address to connect to the switch
(i.e.: 192.168.0.2).
• In a web browser, enter the URL 192.168.0.99.
• Enter the username and password.
9.3 GUI OVERVIEW
This Quick Start Guide will only show a few main or important features to get the user started and
running the OSD254SFP successfully. On the top right hand of the GUI screen there are three icons
available to quickly navigate or obtain help for each GUI menu item.
Home Logout Help
H OME : Clicking the Home button will exit any GUI current screen and display the panel status.
L OGOUT : Clicking the Logout button will logout the current user.
H ELP : Clicking the Help button will open a help window for the current open menu window and
display all functions and input arguments for that page.

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 14
9.4 IP CONFIGURATION
In the treemap on the left of the GUI, expand the Configuration System IP.
Enter the IPv4 address and Mask Length in the table.
Choose the management VLAN ID to access that IP in VLAN table if VLAN function is required.
If the multiple IP addresses are required, click Add Interface to add more IP interface.
Click Save to save the configuration.
Use new IP address to access the switch.
PS: All configuration changes must be saved otherwise all the changes will be lost after
rebooting!

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 15
9.5 USERS AUTHENTICATION
In the tree map on the left of the GUI, expand the Configuration SecuritySwitchUsers
Click admin to change the current admin account setting.
If multiple users are required, click Add New User
PS: All configuration changes must be saved otherwise all the changes will be lost after
rebooting!

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 16
9.6 SAVE CONFIGURATION TO START-UP
In the treemap below, expand the Maintenance Configuration, then select Save startup-config.
Click Save Configuration to save the configuration on start-up.
9.7 PORT SPEED SETTING
The default port speed settings for the OSD2790SFP is 1Gbps. If the user uses 100Mbps SFP devices,
the unit will have to have those ports manually set to 100Mbps for correct operation. In the tree map
below expand the Configuration menu and select Ports. Select Port number then in the Speed
Configured column from the drop down menu select the 100Mbps option. Click Save to save setting.

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 17
10 WARRANTY
Thank you for purchasing equipment designed, manufactured and serviced by Optical Systems Design
(OSD). OSD warrants that at the time of shipment, its products are free from defects in material and
workmanship and conforms to specifications. Our Warranty conditions are outlined below:
10.1 WARRANTY PERIOD
For warranty period, please call your local OSD distributor.
10.2 REPAIRS
Optical Systems Design reserves the right to repair or replace faulty modules/units. Please obtain a
“Return Material Authorisation” (RMA) form and number before returning goods.
Goods must be returned in adequate packing material to Optical Systems Design, Warriewood or its
nominated authorised representative, for all repairs.
10.2.1 WARRANTY REPAIRS
Return shipments to OSD shall be at customer's expense and freight back to the customer will be at
OSD expense.
10.2.2 OUT-OF-WARRANTY REPAIRS
OSD reserves the right to repair or replace any faulty goods. Freight costs and insurance for both
journeys are met by the user. All equipment repaired by OSD will have a 3-Month Warranty from the
date of dispatch.
10.2.3 SITE REPAIRS
By agreement site repairs may be undertaken for which out of pocket, hotel and travel expenses will be
charged.
10.2.4 EXCLUSIONS
This warranty does not apply to defects caused by unauthorized modifications, misuse, abuse or
transport damage to the equipment. All modifications to OSD’s standard product will need written
authorization and will be charged at normal repair rates. All modifications are to be carried out by OSD
Technicians. Warranty is void if unauthorized removal and/or tampering with serial number and/or
repair labels is evident.

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 18

OPTICAL SYSTEMS DESIGN
DOC ID: 10117502
OSD2790SFP QUICK START GUIDE
PAGE 19

Optical Systems Design Pty. Ltd.
7/1 Vuko Pl. Warriewood 2102
P.O. Box 891 Mona Vale
N.S.W. Australia 2103
Telephone: [phone]
Facsimile: [phone]
Email: [email protected]m.au
Web Site: www.osd.com.au
OPTIC L
SYSTEMS
DESIGN
PTY LTD A.B.N. 83 003 020 504
Printed in Australia