opto engineering MACHINE VISION LAB KIT User manual

V 1.0 - eng
QUICK START GUIDE
MACHINE VISION LAB KIT

V 1.0 - eng 2
MACHINE VISION LAB KIT | QUICK START GUIDE
INDEX
1. Disclaimer......................................................................................... 3
2. Safety note........................................................................................ 4
3. General description.......................................................................... 5
4. Content of the Kit ............................................................................. 5
5. Getting Started.................................................................................. 7
5.1. PC Hardware requirements.........................................................................................7
5.2. Software installation walkthrough .............................................................................7
5.2.1. OECS (Opto Engineering Camera Studio) v1.0.0...............................................7
5.2.2. FabImage Studio installation...............................................................................8
5.3. Lens selection - Field of View calculation...............................................................10
5.4. Camera Mounting and back focal adjustment on Telecentric Lens.......................11
5.4.1. Assembling TC3MHR048 on CMHO048............................................................11
5.4.2. Camera mounting and back focal adjustment .................................................11
5.4.3. Filter mounting...................................................................................................12
5.5. Camera Setup............................................................................................................12
5.5.1. Introduction........................................................................................................13
5.5.2. Electrical interface .............................................................................................13
5.5.3. Camera installation and operation....................................................................14
5.5.4. Host network configuration...............................................................................14
5.5.5. Camera network configuration..........................................................................16
5.6. Lighting setup ...........................................................................................................17
5.6.1. Introduction........................................................................................................17
5.6.2. Current ratings...................................................................................................17
5.6.3. Wiring guide .......................................................................................................19
5.6.4. Power up.............................................................................................................19
5.6.5. Configuration......................................................................................................20
5.7. Getting an image in FabImage Studio......................................................................23

V 1.0 - eng 3
MACHINE VISION LAB KIT | QUICK START GUIDE
1. Disclaimer
●OPTO ENGINEERING declines every and all responsibilities for incorrect use of the product
and should not be responsible for any error or omission.
●The instructions supplied at the time of delivery cannot cover all eventualities that might be
verified during the installation, use or maintenance. If any further information relative to
particular procedures of installation, use, and maintenance of the product is required, please
contact the representative person of OPTO ENGINEERING.
●OPTO ENGINEERING declines every and all responsibilities for possible damages of any
type to persons or things, which could be a direct or indirect consequence of the wrong choice
made by the client/user, or of the unsuccessful observance of all the prescriptions indicated
in the Documentation and in the manuals of use and of assembling. Specific manuals of the
components making part of the present Product are supplied with the components and are
available at www.opto-e.com website.
●The buyers/users of theOPTO ENGINEERING Product should proceed, under the own direct
responsibility and at their own care and expenses, with all necessary and appropriate
controls, test, verifications and eventual operating trials, inorder to verify the correspondence
of the OPTO ENGINEERING Product to their necessities or requirements.
●The advantages or the disadvantages of the OPTO ENGINEERING Product use for any
utilization or application can be evaluated in a most critical and complete way only and
exclusively through the verifications, analyses and the tests made by the very buyers/users.
●The possible invalidity or ineffectiveness of one or any more clauses of present Disclaimer
will not affect the validity and the efficacy of other provisions. In such a case, the invalid or
ineffective clause will be substituted with a valid and effective one that achieves in the most
possible way, the same results and the intention of OPTO ENGINEERING.

V 1.0 - eng 4
MACHINE VISION LAB KIT | QUICK START GUIDE
2. Safety note
These instructions are intended to ensure that user can use the product correctly to avoid danger or
property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Warnings
●Proper configuration of all passwords and other security settings is the responsibility of the
installer and/or end-user.
●In the useof the product,you must be instrict compliance with the electricalsafety regulations
of the nation and region. Please refer to technical specifications for detailed information.
●Do not connect several devices to one power adapter as adapter overload may cause over-
heating or a fire hazard.
●Please make sure that the plug is firmly connected to the power socket. When the product is
mounted on wall or ceiling, the device shall be firmly fixed.
●If smoke, odor or noise rise from the device, turn off the power at once and unplug the power
cable, and then please contact the service center.
Cautions
●Make sure the power supply voltage is correct before using the devices.
●Do not drop the devices or subject them to physical shock.
●Do not place the devices in extremely hot, cold, dusty or damp locations, and do not expose
it to high electromagnetic radiation.
●To avoid heat accumulation, good ventilation is required for operating environment.
●Keep the devices away from liquid while in use.
●If the product does not work properly, please contact our technical support. Never attempt to
disassemble the devices yourself. (We shall not assume any responsibility for problems
caused by unauthorized repair or maintenance.)

V 1.0 - eng 5
MACHINE VISION LAB KIT | QUICK START GUIDE
3. General description
This is a quick start guide to the use of the MVKIT-STR product bundle. When this guide is correctly
followed, the user will be able to connect all the parts of the bundle and to acquire an image from
the camera.
4. Content of the Kit
Software
FIS-PRO
FabImage Studio license (hosted by USB-DONGLE-FI)
USB-DONGLE-FI
USB Dongle for software license
Camera
COE-123-M-POE-080-IR-C
Area Scan camera, 1.1", 12 Mpixel, GigE, B/W
Lenses
EN10MPL1220
Fixed focal lens for 12MP camera, focal length 12 mm
EN10MPL1620
Fixed focal lens for 12MP camera, focal length 16 mm
EN10MPL2520
Fixed focal lens for 12MP camera, focal length 25 mm
EN10MPL3520
Fixed focal lens for 12MP camera, focal length 35 mm
EN10MPL5020
Fixed focal lens for 12MP camera, focal length 50 mm
TC3MHR048-C
High resolution telecentric lens for 1.1” detectors, magnification 0.303x, C-mount
Lighting
LTRN048YY1
Ring LED illuminator, inner diameter 75 mm, straight type
LT2BC096072-Y2
High uniformity continuous LED backlights, 96 x 72 mm
LT5WRG200-00-1-Y-24V2
LED dome light, 232 mm outer diameter, 24V
LT2QOG070-00-X-Y-24V2
LED coaxial light, 70x70 mm light emitting area, 24V
LTZZO130-75-3-Y-24V2
LED low angle ringlight, 3 LED rows, outer diameter 131 mm, 75°, 24V

V 1.0 - eng 6
MACHINE VISION LAB KIT | QUICK START GUIDE
Accessories
FTBP470M40.5
Blue (470 nm) bandpass filter with M40.5 mount for fixed focal lenses.
FTBP525M40.5
Green (525 nm) bandpass filter with M40.5 mount for fixed focal lenses.
FTBP635M40.5
Red (635 nm) bandpass filter with M40.5 mount for fixed focal lenses.
RT-PR032-40.5
Linear polarizer filter. Mount Thread M40.5 x P 0.5
CMHO048
Clamping mechanics for TCxx048 lenses and LTCLHP048-X illuminators
CMLT5WRG200-00-X
Bracket for LED dome light, 232 mm outer diameter
LTDVE4CH-20
Strobe controller 4 channels
RT-POE21U-1AF
Power Over Ethernet (POE) Injector
RT-SDR-75-12
75.6W 12V 6.3A DinRail Power Supply
CBETH003
Ethernet cable, CAT6, industrial level, high flexible cable with screw, 5 m
COE-6P-OPEN1-030
HIROSE 6-pin/Open end cable, 3 meters
RT-702611323
Power cord
RT-SDR-120-24
Power supply
CBSLH-24V-F-3M
Illumination cable, side A flying leads, side B SM 3 way female connector, 24V - 3m
CBSLH-24V-F-3M-TB
Illumination cable, side A SM 3 way male connector, side B terminal blocks connector, 24V - 3m
1. YY digits stands for color. RD = red, GR = green, BL = blue, NW = white.
2. Y digit stands for color. R = red, G = green, B = blue, W = white.
3. Different part number available for -UK, -US or -CN plug.

V 1.0 - eng 7
MACHINE VISION LAB KIT | QUICK START GUIDE
5. Getting Started
5.1. PC Hardware requirements
●Windows 7 or greater
●2x Gigabit Ethernet ports with jumbo frames support
●1x USB 2.0 port or greater for USB-DONGLE-FI
●At least 1GB of hard disk space for software installation
5.2. Software installation walkthrough
5.2.1. OECS (Opto Engineering Camera Studio) v1.0.0
1. Download the installation archive from the following link:
https://www.opto-e.com/products/COE-U-series#Downloads
2. Extract the archive
3. Double click on the installation executable:
4. Click on “Start Setup” (ensure to have accepted the terms of the license agreement)

V 1.0 - eng 8
MACHINE VISION LAB KIT | QUICK START GUIDE
5. Ensure to activate all drivers (GigE and USB 3.0) and to enable jumbo frames:
6. Wait until the installation is finished
5.2.2. FabImage Studio installation
1. Download FabImage:
a. Visit webpage at the following link: https://www.fab-image.com/user_area/
b. You must to Login in the user area, if you don’t have a valid account, you need to
create one. Registration form is in the same page of the login.

V 1.0 - eng 9
MACHINE VISION LAB KIT | QUICK START GUIDE
c. After login, go to Download page and select the latest version of FabImage Studio.
Warning: you need to download the full version, NOT the Lite one.
2. Install FabImage Studio following this guide: https://docs.fab-
image.com/current/studio/getting_started/Installation.html. Ensure to select “Hardware
license key runtime” during installation, since the Fabimage Studio license provided in this
kit is hosted by a hardware dongle.

V 1.0 - eng 10
MACHINE VISION LAB KIT | QUICK START GUIDE
5.3. Lens selection - Field of View calculation
In the section of “Resource” on the Opto Engineering website, a Lens selection tool can assist to
find a suitable lens based on the object size and the camera used. https://www.opto-
e.com/selection_form.
In the table below are summarized the angular Field of view of kit lenses considering the detector
size of kit camera.
Lenses
PN
Description
Focal length
[mm]
FOV Angle
H [°]
V [°]
D [°]
EN10MPL1220
Fixed focal lens for 12MP
camera, focal length 12 mm
12
49.7
40.8
55.6
EN10MPL1620
Fixed focal lens for 12MP
camera, focal length 16 mm
16
41.5
32.9
47.6
EN10MPL2520
Fixed focal lens for 12MP
camera, focal length 25 mm
25
29.5
22.5
35.0
EN10MPL3520
Fixed focal lens for 12MP
camera, focal length 35 mm
35
22.0
16.5
26.6
EN10MPL5020
Fixed focal lens for 12MP
camera, focal length 50 mm
50
15.8
11.7
19.3
In order to find the linear field of view at a certain working distance a simple trigonometrical
calculation has to be done.