3M
™Adflo
™Powered Air Respirator
•
•
•
•
•
834017
834018
835000
835005
836000
836010
837010
837110
837120
837242
837542
837620
837621
837630
837631
837730
837731
838031
ADAPTOR ADFLO BREATHING TUBE 9100 FX AIR
ADAPTOR QRS BREATHING TUBE TO 9000
PAPR MOTOR WITH HOUSING ADFLO
CHARGER BATTERY NIMH ADFLO
CHARGER BATTERY LI-ION ADFLO
BATTERY MULTI-STATION ADFLO
TUBE BREATHING SELF ADJUSTING QRS ADFLO
TUBE BREATHING HEAVY DUTY RUBBER QRS ADFLO
TUBE BREATHING COVER FLAME RESISTANT ADFLO
BELT ADFLO
BELT EXTENSION ADFLO
SPARK ARRESTOR ADFLO
PRE-FILTER ADFLO PK=5
FILTER PARTICLE PSL ADFLO
FILTER ODOUR ADFLO
FILTER ODOUR REPLACEMENT PAD ADFLO
FILTER NUIS LEVEL ORGANIC VAPOUR/ACID GAS
ADFLO FILTER GAS A1 ADFLO
BATTERY STANDARD NIMH ADFLO
BATTERY HEAVY DUTY NIMH ADFLO
BATTERY STANDARD LI-ION ADFLO
BATTERY HEAVY DUTY LI-ION ADFLO
RESPIRATOR STANDARD LI-ION ADFLO
RESPIRATOR HEAVY DUTY LI-ION ADFLO
FILTER COVER LI-ION ADFLO
Part No
Before use After use
•
•
•
•
•
•
•
•
Further information and advice
To request a quote or place an order for spare parts, please contact SFI on (03) 9088 6060. Please note that higher than normal levels of pollutants, heat and sparks
will require more frequent replacement of components. If you require additional guidance, please check the care and maintenance videos on our YouTube Channel
(www.youtube.com/user/3MSpeedglas) or contact SFI Australia.
Care & Maintenance
533505
533506
832000
833101
833111
833709
834016
Description Part No Description Part No Description PartNo Description
Scan this QR-code to see
videos and learn more about
care and maintenance of your
Speedglas welding helmet
SFI OrbiMAX
501-503 Dowling Street
Wendouree Vic 3355
T: (03) 9088 6060
E: sales@saust.com.au
W: www.sperformax.com.au
83 80 30 83 60 00
83 60 10
83 60 80
83 70 10
83 70 80
83 50 00
83 50 10 83 31 01
83 25 30
83 76 20 83 80 20
83 71 20
83 71 10
83 72 42
83 20 00 83 76 21
83 32 09
83 40 16
83 40 17
83 75 42
83 50 05
83 40 18
53 35 06
83 76 31
83 76 20
83 76 21
83 80 31 83 76 30 83 31 11
83 77 30
83 31 01
83 80 30 83 60 00
83 60 10
83 60 80
83 70 10
83 70 80
83 50 00
83 50 10 83 31 01
83 25 30
83 76 20 83 80 20
83 71 20
83 71 10
83 72 42
83 20 00 83 76 21
83 32 09
83 40 16
83 40 17
83 75 42
83 50 05
83 40 18
53 35 06
53 35 05
* Speedglas 9000 headtop breathing tubes.
Battery. Ensure that it’s adequately charged
and tted correctly.
Motor Body. Inspect the unit for damage and
ensure it’s rmly xed to the belt. Ensure lters
are correctly tted.
Breathing tube. Inspect the tube and connec-
tions to ensure they are free from splits and
holes. Replace if damaged, deformed or leaking
any air. To extend the life of the breathing tube,
use a tube cover or the heavy-duty rubber
breathing tube.
Air ow check. Fit the breathing tube to the
unit and attach the airow meter in the other
end of the tube and switch on the Ado PAPR. If
the ball does not rise above the line, continue
fault nding.
Alarm check. Cover the air outlet of the airow
meter with your hand until an audible warning
is heard and the red indicator illuminates.
Remove your hand. The alarm should now stop.
Clean the equipment. Wipe the motor body with a moist
tissue or cloth. If you suspect that the inside of the breathing
tube is dirty, it must be changed.
DO NOT rinse, immerse in water or clean with solvents.
DO NOT attempt to remove contamination of lters as this will
damage the lters and void the warranty.
Replace damaged parts. Replace all damaged parts to guaran-
tee the proper functioning of the respirator. Worn out compo-
nents should be disposed of according to local regulations.
Spark arrestor. Replace if deformed and no longer tting
well.
Prelter. Replace regularly to extend the life of the particle
lter. This will save money and also extend the battery
run-time.
Particle lter. Check the lter indicator position and replace if
the red LED is lit. Otherwise, replace whenever the battery
operating time becomes too short, or when “fully loaded” lter
triggers low airow alarm.
Gas lter. Replace the gas lter according to your work place
requirements. Do not wait until you can sense odours or
smells.
Odour lter. Replace any time you smell unpleasant odours.
Odour lter is not required if gas lter is used.
Storage. Put the battery/turbo unit on charge after use. When
stored, recharge every six months. Store the unit in a dry, clean
area away from direct sunlight, high temperatures and
solvents. For example use
To optimise the eective lifetime of your welding equipment and avoid the additional cost of
replacement, regular maintenance is important. Replace all damaged parts immediately to
ensure correct levels of protection.
